Abstract:Purpose: The aim of this study was to evaluate the corrosion behavior of a Ni-Cr dental casting alloy subjected to 10% hydrogen peroxide (HP) and 10% carbamide peroxide (CP) bleaching solutions and to determine the composition of the surface oxide layer formed on the alloy specimens. Materials and methods: Ten cylindrical specimens (4 mm in diameter × 25 mm in height) were cast from a Ni-Cr alloy (Wiron 99) and divided into two groups (n = 5). A potentiodynamic polarization test was used to compare the corrosion rates of specimens in HP and CP (pH = 6.5). Before cyclic polarization tests, all alloy specimens were allowed to reach a steady open circuit potential (Ecorr ) for a period of 1 hour. Then tests were initiated at 100 mV versus standard calomel electrode (SCE) below Ecorr and scanned at a rate of 1 mV/s in the anodic direction until reaching 1000 mV over the Ecorr value. The scan then was reversed back to the Ecorr of the specimens. The open circuit potentials (Ecorr ) and the current densities (Icorr ) were determined using the anodic Tafel regions extrapolating from the curves. Differences in Ecorr and Icorr were determined using one-way ANOVA (α = 0.05). In addition, corrosion rates were calculated from these curves. Before and after polarization tests, a scanning electron microscope (SEM) examination accompanied by energy dispersive X-ray spectroscopy (EDS) was used to analyze the surface morphology. The surface characterization of the passive film formed on alloy specimens was also performed by using X-ray photoelectron spectroscopy (XPS). Results: In this study, bleaching agents had an effect on the anodic process for two groups. Although no statistical difference was identified between the groups for both corrosion parameters, results indicated that the effect of CP on the corrosion behavior was less than that of HP. These results agreed with the SEM observations. XPS data showed that oxide layers formed on all groups contained mainly Cr2 O3 , NiO, and MoO3 , and the amounts of oxides formed on CP-treated specimens were higher than HP treated ones. Also, molybdenum rates were increased with CP application compared to HP. Conclusions: The comparison of the effects of the two bleaching agents at 10% showed that the alloy suffered less corrosion with CP than HP. This result was also confirmed by the SEM and XPS data. The presence of Mo on the oxide layer affected the oxide layer, leading to lower corrosion rates.

The electrochemical behavior and surface analysis of Ti<sub>49.6</sub>Ni<sub>45.1</sub>Cu<sub>5</sub>Cr<sub>0.3</sub>alloy for orthodontic usage

The Electrochemical Behavior And Surface Analysis Of Ti49.6ni45.1cu5cr0.3 Alloy For Orthodontic Usage

The Electrochemical Behavior and Surface Analysis of Ti50Ni47.2Co2.8 Alloy for Orthodontic Use

The Effect on the Corrosion Resistance of Ti Alloy in the Artificial Saliva with Different pH Value

An electrochemical study on corrosion behavior of three alloys in artificial saliva with different pH

Electrochemical Impedance Investigation of Ni-free Co-Cr-Mo and Co-Cr-Mo-Ni Dental Casting Alloy for Partial Removable Dental Prosthesis Frameworks

Electrochemical Corrosion Behaviour of Ti44Ni47Nb9 Alloy in Simulated Body Fluids

The electrochemical behavior of a Ti50Ni47Fe3 shape memory alloy

In vitro corrosion behavior of nano-multilayered TiN/Ti coated NiTi alloy

Electrochemical and surface characterization of a nickel–titanium alloy

Analysis and Comparison of the Corrosive Behavior of Nickel-Based and Cobalt-Based Dental Alloys

The corrosion behavior of three alloys and Ti abutment

Corrosion and wear behavior of Ti-5Cu-xNb biomedical alloy in simulated body fluid for dental implant applications

[Corrosion Resistance and Wear Resistance of Ni-Cr Alloy after Coating Titanium Nitride (tin) in Oral Containing Fluorine Environment].

Electrochemical corrosion and surface analyses of a ni-cr alloy in bleaching agents

Influence of Fluoride and Chloride on Corrosion Behavior of NiTi Orthodontic Wires.

Comparative Study on the Corrosion Behavior of Ti–Nb and TMA Alloys for Dental Application in Various Artificial Solutions

Electrochemical Corrosion Characteristics of Ni-Cr Alloy in Artificial Saliva

[Effect of TiN Coating on Corrosion Resistance of Dental NiCr Alloy].

Corrosion Resistance of Dental Alloys in Artificial Saliva

Improved Corrosion Resistance of Dental Ti50Zr Alloy with (tizr)n Coating in Fluoridated Acidic Artificial Saliva