Abstract:Aim: To analyse the type and location of defects in HyFlex CM instruments after clinical use in a graduate endodontic programme and to examine the impact of clinical use on their metallurgical properties. Methodology: A total of 468 HyFlex CM instruments discarded from a graduate endodontic programme were collected after use in three teeth. The incidence and type of instrument defects were analysed. The lateral surfaces of the defect instruments were examined by scanning electron microscopy. New and clinically used instruments were examined by differential scanning calorimetry (DSC) and x-ray diffraction (XRD). Vickers hardness was measured with a 200-g load near the flutes for new and clinically used axially sectioned instruments. Data were analysed using one-way anova or Tukey's multiple comparison test. Results: Of the 468 HyFlex instruments collected, no fractures were observed and 16 (3.4%) revealed deformation. Of all the unwound instruments, size 20, .04 taper unwound the most often (n = 5) followed by size 25, .08 taper (n = 4). The trend of DSC plots of new instruments and clinically used (with and without defects) instruments groups were very similar. The DSC analyses showed that HyFlex instruments had an austenite transformation completion or austenite-finish (Af ) temperature exceeding 37 °C. The Af temperatures of HyFlex instruments (with or without defects) after multiple clinical use were much lower than in new instruments (P < 0.05). The enthalpy values for the transformation from martensitic to austenitic on deformed instruments were smaller than in the new instruments at the tip region (P < 0.05). XRD results showed that NiTi instruments had austenite and martensite structure on both new and used HyFlex instruments at room temperature. No significant difference in microhardness was detected amongst new and used instruments (with and without defects). Conclusions: The risk of HyFlex instruments fracture in the canal is very low when instruments are discarded after three cases of clinical use. New HyFlex instruments were a mixture of martensite and austenite structure at body temperature. Multiple clinical use caused significant changes in the microstructural properties of HyFlex instruments. Smaller instruments should be considered as single-use.

Correlation study of defects in Mtwo instruments after clinical use

Analysis of Mtwo Rotary Instrument Separation During Endodontic Therapy: A Retrospective Clinical Study

Defects in ProTaper S1 instruments after clinical use: fractographic examination

Cyclic fatigue resistance of new and used Mtwo rotary nickel-titanium instruments in two different radii of curvature

HyFlex nickel-titanium rotary instruments after clinical use: metallurgical properties

ProFile Vortex instruments after clinical use: a metallurgical properties study

Characterisation of Deformed or Separated Nickel-Titanium Retreatment Instruments after Clinical Use - A Multicentre Experience

ProFile Vortex and Vortex Blue Nickel-Titanium Rotary Instruments after Clinical Use

Surface roughness and cyclic fatigue resistance of a novel shaping system: An in-vitro study

Scanning Electron Microscopic Analysis of Deformation of TruNatomy File Systems: An Ex-vivo Study

Cyclic fatigue resistance of two pediatric rotary files manufactured with different heat treatments: an in-vitro study

Torsional behaviour of rotary NiTi ProTaper Universal instruments after multiple clinical use

Effect of Autoclave Sterilization on the Number of Uses and Resistance to Cyclic Fatigue of WaveOne Gold and Four Replica-Like Endodontic Instruments

In vitro study of structural and chemical changes in two reciprocating files after multiple reuses and sterilisation

SEM evaluation of canal wall dentine following use of Mtwo and ProTaper NiTi rotary instruments

Evaluation of apical root defects during canal instrumentation with two different nickel-titanium (NiTi) systems by optical coherence tomography (OCT) scan

Impact of pecking amplitude on cyclic fatigue of new nickel-titanium files

Impact of Angle of File Access and Location of Canal Curvature on the Dynamic Cyclic Fatigue of Nickel Titanium Rotary Instruments

Assessment of Incidence, Management and Contributory Factors of Root Canal Instrument Separation in an Endodontics Post- Graduate Program: A Retrospective Clinical Study

An Investigation of the Metal Fatigue of Different Nickel-Titanium Rotary Instruments After Prolonged Use

Influence of cross-sectional design and dimension on mechanical behavior of nickel-titanium instruments under torsion and bending: a numerical analysis.