A Dramatic pH Effect Leads to a Catalytic Asymmetric Epoxidation.

Zhi-Xian Wang,Y. Tu,M. Frohn,Yian Shi

DOI: https://doi.org/10.1002/CHIN.199736038

1997-04-18

Abstract:

What problem does this paper attempt to address?

In vitro evaluation of cyclic fatigue resistance of thermally treated novel nickel-titanium rotary instruments

Bianca Reis Assaf,Júlia Carolina Verçosa,Vanessa Horrane da Silva Costa,Alice Machado Carvalho Santos,Marcos Frozoni,Alexandre Moreira Fernandes

DOI: https://doi.org/10.33448/rsd-v11i7.29870

2022-05-26

Abstract:The objective of this study was to evaluate the cyclic fatigue resistance of novel NiTi files (subjected to heat treatment) using the in vitro model (artificial canal). Twelve ProDesign Logic instruments - PDL 25/.06 (Easy Equipamentos Odontológicos, Belo Horizonte, Brazil) and 12 Protaper Next X2 instruments - PTN (tip 25) were included in this research. The Static cyclic fatigue test was performed with a grooved stainless steel block simulating a canal of 1,5 mm diameters, a 60o angle of curvature and 5 mm radius. The files were positioned inside the artificial canal and rotated until the fracture occurred. Using the time until fracture (seconds) and the number of rotations per minute (RPM), the number of cycles until fracture (NCF) was calculated and the length of ruptured fragments was registered. Three samples from each group were analyzed in Scanning Electronic Microscopy (SEM) to characterize the metal rupture. Data were analyzed using the Mann-Whitney non-parametric test and the level of significance considered was p<0.05. PDL obtained a mean value of 956,0 NCF (352,0 - SD) and PTN achieved 391,0 NCF (36.7 - SD) with statistical significance between the groups (p 0.05). SEM analysis showed features compatible with ductile fracture. ProDesign LOGIC files showed higher NCF than Protaper Next X2. There was no difference between groups considering the length of the ruptured fragment.
Comprehensive Assessment of Cyclic Fatigue Strength in Five Multiple-File Nickel–Titanium Endodontic Systems

Jorge N. R. Martins,Emmanuel J. N. L. Silva,Duarte Marques,Francisco M. Braz Fernandes,Marco A. Versiani

DOI: https://doi.org/10.3390/ma17102345

IF: 3.4

2024-05-16

Materials

Abstract:The resistance of nickel–titanium endodontic instruments against cyclic fatigue failure remains a significant concern in clinical settings. This study aimed to assess the cyclic fatigue strength of five nickel–titanium rotary systems, while correlating the results with the instruments' geometric and metallurgical characteristics. A total of 250 new instruments (sizes S1/A1, S2/A2, F1/B1, F2/B2, F3/B3) from ProTaper Gold, ProTaper Universal, Premium Taper Gold, Go-Taper Flex, and U-Files systems underwent mechanical testing. Prior to experimental procedures, all instruments were meticulously inspected to identify irregularities that could affect the investigation. Using a stereomicroscope, design characteristics such as the number of spirals, length, spirals per millimeter, and average helical angle of the active blade were determined. The surface finishing characteristics of the instruments were examined using a scanning electron microscope. Differential scanning calorimetry was employed to establish the instruments' phase transformation temperatures, while energy-dispersive X-ray spectroscopy was utilized to analyze the elemental composition of the alloy. The instruments were subjected to cyclic fatigue testing within a stainless steel non-tapered artificial canal featuring a 6 mm radius and 86 degrees of curvature. Appropriate statistical tests were applied to compare groups, considering a significance level of 0.05. The assessed design characteristics varied depending on the instrument type. The least irregular surface finishing was observed in U-Files and Premium Taper Gold files, while the most irregular surface was noted in Go-Taper Flex. All instruments exhibited near-equiatomic proportions of nickel and titanium elements, whereas ProTaper Universal and U-Files instruments demonstrated lower phase transformation temperatures compared to their counterparts. Larger-sized instruments, as well as ProTaper Universal and U-Files, tended to display lower cyclic fatigue strength results. Overall, the design, metallurgical, and cyclic fatigue outcomes varied among instruments and systems. Understanding these outcomes may assist clinicians in making more informed decisions regarding instrument selection.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
An Investigation of the Metal Fatigue of Different Nickel-Titanium Rotary Instruments After Prolonged Use

Kerem Engin AKPINAR,Gizem KUTLU CENGİZ

DOI: https://doi.org/10.7126/cumudj.1098476

2022-05-16

Cumhuriyet Dental Journal

Abstract:Objective:This study aimed to compare the cyclic fatigue (CF) resistance of nickel-titanium (Ni-Ti) endodontic instruments from ProTaper (PTU), ProTaper Next (PTN), Wave One (WO), and Reciproc (RPC). Materials and Methods:In our study, PTU, PTN, WO, and RPC rotary files were divided into the experimental and control groups containing an equal number of samples. The experimental group files were used in the shaping of 80 extracted human lower premolar and lower molar teeth. The experimental and control group kits were then placed in the test apparatus and observed until they fractured. Fracture times were recorded and statistically evaluated. Results:In the one-to-one comparisons of the experimental and control group files, while the differences between the fracture times of the experimental and control group files were found to be statistically insignificant in RPC, WO, PTU, and PTN X1 files (p>0.05), fracture time differences were statistically significant in all PTN X2 files (p0.05). Conclusion:The files used with reciprocal movement were found to be safer in terms of metal fatigue when compared to the other files used with rotational movement after the preparation.
Characterization of a novel canine T-cell line established from a spontaneously occurring aggressive T-cell lymphoma with large granular cell morphology.

C. Bonnefont-Rebeix,C. Fournel-Fleury,F. Ponce,S. Belluco,D. Watrelot,Sylvie E Bouteille,Sylvie Rapiteau,Diane Razanajaona-Doll,J. Pin,C. Leroux,T. Marchal

DOI: https://doi.org/10.1016/j.imbio.2015.08.007

IF: 3.152

Immunobiology

Abstract:
Comparison of cyclic fatigue resistance of four pediatric rotary file systems at body temperature: an in vitro study

Koray Surme,Hayri Akman,Hatice Büyüközer Özkan,Kürşat Er

DOI: https://doi.org/10.1186/s12903-024-04739-z

2024-08-23

BMC Oral Health

Abstract:Background: The aim of this study was to compare the cyclic fatigue resistance (CFR) of the newly developed pediatric nickel-titanium (NiTi) rotary file systems for root canal preparation of primary teeth. Methods: Eighty pediatric NiTi rotary file systems files were used in this study, including 20 EasyInSmile X-Baby (25/0.04), 20 Scope miniScope (25/0.04), 20 EndoArt Pedo Gold (25/0.04), and 20 EndoArt Pedo Blue (25/0.04) files. Static CFR tests; performed on a custom-made stainless steel block with an inner diameter of 1.5 mm, an angle of curvature of 60° and a curved artificial canal with a radius of curvature of 5 mm. The test system was filled with distilled water and the temperature was kept constant at 35 ± 1 °C. The files were rotated in the simulated canal until fracture occurred. The number of cycles to failure (NCF) data was recorded, and all the fracture surfaces of the files were evaluated using scanning electron microscopy (SEM). One-way ANOVA and Tukey tests were used for statistical analysis of the data, and the significance level was set at p < 0.05. Results: EndoArt Pedo Blue showed the highest NCF values (2668.10 ± 755.26), while the miniScope showed the lowest NCF values (453.65 ± 72.51), with a statistically significant difference between all the tested file systems (p < 0.05). There was no statistical difference in terms of fractured fragment lengths among all tested files (p > 0.05). Conclusion: The EndoArt Pedo Blue file system showed the best CFR performance among the four file systems specifically designed for primary teeth.
Impact of Angle of File Access and Location of Canal Curvature on the Dynamic Cyclic Fatigue of Nickel Titanium Rotary Instruments

Dina Assaf,Mohammed Abou El Seoud,Mohammed Kataia,Shehabeldin Saber

DOI: https://doi.org/10.14744/eej.2023.71676

2024-03-08

Abstract:Objective: To evaluate the impact of different file access angles and root canal curvature's location on the fatigue failure of One Curve (OC) and E3 Azure (EZ) NiTi files using a dynamic model at simulated body temperature. Methods: Eighty new instruments with similar tip sizes and taper (#25/0.06) from two NiTi rotary systems, One Curve and E3 Azure, were tested at simulated body temperatures (37°C) using a custom-made dynamic cyclic fatigue device. Instruments were divided into four subgroups according to the location of root canal curvature (a coronal curve 5 mm from the root canal orifice and an apical curve 10 mm from the root canal orifice) and the angle of file access (0° or 30°). Instruments were operated in simulated stainless-steel canals having a 60° curve and a 3 mm radius. A custom-made device produced controlled vertical pecks during file rotation. Time to failure (sec) was registered, and the length of the fragment segments was measured (mm). Data were analysed statistically with One-Way ANOVA and Tukey post hoc tests. The significance level was set at 5%. All separated instruments were examined by scanning electron microscope. Results: One-way ANOVA (p<0.05) found a significant difference among the tested instruments. Post Hoc analysis revealed lower cyclic fatigue resistance when the angle of file access was 30º, and the root canal curvature was located coronally for both files (p<0.0001). Three-way ANOVA showed that the angle of file access was the most influential contributor to cyclic fatigue, followed by the location of file curvature and, finally, the file type (p<0.0001). The fractographic examination revealed a predominantly ductile fracture mode for all tested instruments. The lengths of all fractured segments showed no significant difference (p>0.05), indicating an accurate trajectory during testing. Conclusion: OC files had superior cyclic fatigue resistance than EZ files; coronal curvatures negatively impacted cyclic fatigue resistance compared to apical curvatures, while the angle of file access presented the highest impact on dynamic cyclic fatigue.
In Vitro Analysis of the Fatigue Resistance of Four Single File Canal Preparation Instruments

Mohammad I. Al-Obaida,Abdulmohsen A. Alzuwayer,Saqer S. Alanazi,Abdulrahman A. Balhaddad

DOI: https://doi.org/10.3390/ma15020688

IF: 3.4

2022-01-17

Materials

Abstract:Instrument separation during root canal therapy is inevitable in endodontics with several unfavorable clinical consequences. Therefore, examining the cyclic flexural fatigue resistance of commonly used rotary endodontic files is crucial. This study aimed to determine the cyclic flexural fatigue resistance of four nickel–titanium (NiTi) rotary files used as a single canal preparation technique: WaveOne, Reciproc, Protaper F2, and Unicone medium instruments. According to the manufacturer’s instructions, each file was rotated freely within a 1.3 mm deep and 1.3 mm wide V-shaped groove in a stainless-steel block with a 40° and 5 mm radius of curvature. Cyclic fatigue resistance was compared between the NiTi files by verifying the time needed to crack. The data were analyzed using one-way analysis of variance (ANOVA) followed by Scheffé post hoc with a significant level set at p < 0.05. Our results demonstrated that the WaveOne instrument had the highest cyclic flexural fatigue resistance among the tested groups (p ≤ 0.05), while Unicone had the lowest cyclic flexural fatigue resistance. This study concluded that WaveOne size 25/0.08 could illustrate a superior cyclic flexural fatigue resistance when instrumenting root canals with the lowest possibility to cause instrument separation.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Nickel-Titanium Rotary Instruments: An In Vitro Comparison (Torsional Resistance of Two Heat-treated Reciprocating Files)

Shilpa Bhandi,Marco Seracchiani,Orlando Donfrancesco,Rodolfo Reda,Alessandro Mazzoni,Stefania Nottola,Giuseppe Familiari,Luca Testarelli,Gianluca Gambarini

2021-04-01

Abstract:Aim and objective: The present study aims to evaluate the difference in torsional resistance of two reciprocating nickel-titanium (Ni-Ti) rotary files: WaveOne Gold and EdgeOne Fire. Materials and methods: A total of 40 nickel-titanium rotary instruments (n = 40): 20 WaveOne Gold Small (WOGS) and 20 EdgeOne Fire Small (EOFS) were divided into two groups. Each instrument was tested using a torsional resistance device already validated in previous studies to evaluate and compare torsional resistance. The static torsional test was implemented by blocking each instrument at 3 mm from the tip and rotating it until fracture with a reciprocating motion. Torque to fracture (TtF) and fragment length (FL) were measured and statistically analyzed. Results: Statistical analysis of TtF found significant differences between the two groups (p<0.05). The EOFS showed higher TtF if compared to WOGS, with a mean value and a standard deviation of 3.05 ± 0.07 (N cm) against 2.97 ± 0.08 (N cm). Data for FL showed no significant differences (p>0.05) between the two groups. Conclusion: According to the results of this study, it is reasonable to assert that EOFS instruments showed a higher torsional resistance if compared to the WOGS. Clinical significance: As evidenced by this study, EOFS should be considered as a safer solution, in terms of torsional resistance, if compared to WOGS, reducing the risk of intracanal separation due to excessive torsional load.
Comparative Analysis of NiTi Instruments with Different Alloy Treatments

José Aranguren,Felipe Oliveros-Porras,Ana Ramírez-Muñoz,Irene Pérez,Marcela Salamanca-Ramos,Karim Aazzouzi-Raiss,Alejandro R. Pérez

DOI: https://doi.org/10.3390/ma17194817

IF: 3.4

2024-09-30

Materials

Abstract:This study aims to compare the cyclic fatigue resistance of nickel–titanium (NiTi) endodontic instruments, focusing on the impact of various alloy treatments and manufacturing processes across different generations of these instruments; Twenty instrumentation systems from different generations, comprising both continuous and reciprocating motion designs, were tested. Four hundred instruments underwent cyclic fatigue testing using an INSTRON machine, with the time and number of cycles to fracture (NCF) recorded for each instrument. Statistical analyses were performed to compare the fatigue resistance between systems, generations, and motion types; Instruments treated with advanced thermal processing, such as Excalibur, Reciproc Blue, and TruNatomy, demonstrated superior resistance to fracture, whereas systems like Protaper Universal, K3XF, and 2Shape showed the lowest resistance. Reciprocating instruments generally exhibited higher cyclic fatigue resistance than continuously rotating instruments; Technological advancements in NiTi instrument design, especially the implementation of heat-treated alloys, have improved cyclic fatigue resistance, enhancing the safety and efficiency of endodontic treatments. Reciprocating systems, in particular, exhibit superior fracture resistance, suggesting their greater utility in challenging clinical conditions.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
A comparative study of cyclic fatigue of 6 endodontic systems. An in vitro study

Jorge Rubio,José-Ignacio Zarzosa,Susana Aranda,Alberto Casino,Antonio Pallarés

DOI: https://doi.org/10.4317/jced.59747

2022-07-01

Abstract:Background: Mechanical preparation and the formation of space for adequate obturation are included in root canal shaping, but the complex root canal anatomy may be affect it. Manufacturers have created different alloys like M-Wire, Blue-Wire, Gold-Wire or R-phase. Objective: This investigation was performed to verify the null hypothesis that there were not significant differences between size 25 instruments ESP Files Thermoflex, Protaper Ultimate, Protaper Next, Blueshaper, One Curve and 2Shape about cyclic fatigue and length of broken fragments. Material and methods: 180 new size 25 files of the systems investigated were selected (n=30). Files were used with Endo Mate DT endo motor with speed and torque recommended by manufacturers, holding the instruments with clamping mechanism, with passive adjustment, glycerine and without pressure in a stainless-steel block. The time was calculated in seconds until fracture. Number of fatigue cycles was determined as (Resistance (s) x Speed)/60. Separated fragment lengths were calculated with digital Vernier caliper. Statistical analysis was carried out with the SPSS 18 programme at a 95% confidence level, using Levene´s Test to compare variances, Welch's Test to compare means, and Games-Howell´s Test to reveal differences between groups. Results: Levene's Test determined no equal variances (P<0.05). Welch's Test and ANOVA (P<0.05) showed significant differences in cyclic fatigue and separated fragment lengths. Games-Howell's and Bonferroni´s Test established significant differences in multiple comparisons (P<0.05). Conclusions: ESP Files Thermoflex was superior in cyclic fatigue. About separated fragment lengths, ESP Files Thermoflex, Protaper Ultimate and Blueshaper obtained longer lengths. Key words:Cyclic fatigue, continuous movement, separated fragment lengths, rotary systems.
Cyclic fatigue and torsional strength of three different thermally treated reciprocating nickel-titanium instruments

Murilo Priori Alcalde,Marco Antonio Hungaro Duarte,Clovis Monteiro Bramante,Bruno Carvalho de Vasconselos,Mario Tanomaru-Filho,Juliane Maria Guerreiro-Tanomaru,Jader Camilo Pinto,Marcus Vinicius Reis Só,Rodrigo Ricci Vivan

DOI: https://doi.org/10.1007/s00784-017-2295-8

2017-12-09

Clinical Oral Investigations

Abstract:ObjectivesThe aim of this study was to evaluate the cyclic and torsional fatigue resistance of the reciprocating single-file systems Reciproc Blue 25.08 (VDW GmbH, Munich, Germany), Prodesign R 25.06 (Easy Dental Equipment, Belo Horizonte, Brazil), and WaveOne Gold 25.07 (Dentsply/Tulsa Dental Specialties, Tulsa, OK, USA).Materials and methodsSixty reciprocating instruments of the systems Reciproc Blue R25 (RB #25 .08 taper), Prodesign R (PDR #25 .06 taper), and WaveOne Gold (WOG #25 .07 taper) (n = 20) were used. Cyclic fatigue resistance testing was performed by measuring the time to failure in an artificial stainless steel canal with a 60° angle of curvature and a 5-mm radius located 5 mm from the tip (n = 10). The torsional test (ISO 3630-1) evaluated the torque and angle of rotation at failure of new instruments (n = 10) in the portion 3 mm from the tip. The fractured surface of each fragment was also observed using scanning electron microscopy (SEM). In addition, a supplementary examination was performed to measure the cross-sectional area of each instrument 3 and 5 mm from the tip. The data were analyzed using one-way ANOVA and Tukey’s test, and the level of significance was set at 5%.ResultsThe cyclic fatigue resistance values of PDR 25.06 were significantly higher (P < 0.05). RB 25.08 showed higher fatigue resistance than WOG 25.07 (P < 0.05). The torsional test showed that PDR 25.06 had lower torsional strength (P < 0.05). No differences were observed between RB 25.08 and WOG 25.07 (P > 0.05). PDR 25.06 showed higher angular rotation values than RB 25.08 and WOG 25.07 (P < 0.05). RB 25.08 presented higher angular rotation than WOG 25.07 (P < 0.05). The cross-sectional area analysis showed that PDR 25.06 presented the smallest cross-sectional areas at 3 and 5 mm from the tip (P < 0.05).ConclusionPDR 25.06 presented the highest cyclic fatigue resistance and angular rotation until fracture compared to RB 25.08 and WOG 25.07. In addition, RB 25.08 and WOG 25.07 had higher torsional strength than PDR 25.06.Clinical relevanceIn endodontic practice, thermally treated reciprocating instruments have been used for the root canal preparation of curved and constricted canals; therefore, these instruments should present high flexibility and suitable torsional strength to minimize the risk of instrument fracture.

dentistry, oral surgery & medicine
The effect of canal curvature on cyclic fatigue resistance of rotary instruments using different irrigation materials ( in vitro study)

Mohammed Hamoudi Alsunboli,Sally Saad Ali Ihsan,Duha Qais Sabah

DOI: https://doi.org/10.12688/f1000research.130249.2

2024-04-08

Abstract:Background: The mechanical qualities of Ni-Ti is crucial because they give the files their flexibility and enable us to prepare curved and double-curved canals with more ease. It happens frequently for instruments to separate during canal preparation, and cyclic fatigue (metal fatigue) is a frequent cause.This study aimed to assess how irrigation affected the two rotary endodontic instruments' cyclic fatigue resistance. Methods: The Edge File and Fanta File rotary endodontic instrument groups were chosen. Each group (n = 42) was split into 3 subgroups (n = 14 each), one receiving NaOH, one Glycine, and one EDTA treatment. The number of cycles to failure (NCF) was determined after each subgroup underwent testing for cyclic fatigue resistance. Results: The result appeared different significant between the two group and sub-group with the different materials that used with it with the length of fractures and time that recorded in each group. Conclusion: NaOCl, glycine, and EDTA as chemical materials appeared to have considerably varied cycle fatigue resistance for various lengths of fractures and durations, according to the comparison between the two evaluated instruments.
An in vitro comparative evaluation of cyclic fatigue resistance of two rotary and two reciprocating file systems

G P V Srikumar,Vaishnavi Gadbail,Arvind Kumar Alexander,Geeta Nishad,Shripriya Rahane,J S Beautlin

DOI: https://doi.org/10.4103/JCDE.JCDE_2_24

Abstract:Context: Root canal instrumentation is one of the important procedures for successful endodontic therapy. Unexpected fracture of files occurs during root canal instrumentation without any visible signs of deformation compromising the success of root canal treatment. Aims: The aim of the study was to evaluate and compare cyclic fatigue resistance (CFR) of rotary and reciprocating files in simulated canals with 45°, 60°, and 90° angle of curvature. Settings and design: The study design was an In vitro study. Subjects and methods: Sixty nickel-titanium files, 30 each of rotary and reciprocating files were selected and divided into four groups (n = 15) of Neoendo Flex, ProTaper Next, WaveOne Gold (WOG), and Reciproc Blue (RPB) files. Each group was further subdivided into three subgroups containing five samples each based on their use in simulated canals with 45°, 60°, and 90° angle of curvature. To simulate root canals with 45°, 60°, and 90° angle of curvature, three artificial canals were designed in a stainless steel metal block. Each file was autoclaved, immersed in 3% sodium hypochlorite (NaOCl), and coated with 17% ethylenediaminetetraacetic acid (EDTA). Each file was tested for CFR using a torque-controlled reduction handpiece by instrumenting in a simulated canal for 10 s until fracture. The cycle of autoclaving, exposure to NaOCl, EDTA, and testing of CFR for 10 s per canal as per groups and subgroups was repeated again and again until the respective file fracture. The time taken to file fracture was recorded using a digital chronometer. The time taken for each file fracture (in minutes) was multiplied by the number of rotations per minute to attain the number of cycles to failure (NCF). Statistical analysis used: The obtained results were subjected to statistical analysis using one-way analysis of variance and independent t-test. Results: One-way ANOVA test showed a statistically significant difference between the four groups, P < 0.001. Independent "t"-test between individual subgroups showed a statistically significant difference, as P < 0.05. Conclusions: WOG and RPB reciprocating file systems showed superior CFR, more especially in canals with abrupt 90° angle of curvature compared to both rotary file systems tested. Among rotary file systems tested, Neoendo Flex showed greater CFR than ProTaper Next.
Cyclic fatigue resistance tests of Nickel-Titanium rotary files using simulated canal and weight loading conditions

Ok-In Cho,Antheunis Versluis,Gary SP Cheung,Jung-Hong Ha,Bock Hur,Hyeon-Cheol Kim

DOI: https://doi.org/10.5395/rde.2013.38.1.31

2013-01-01

Abstract:OBJECTIVES: This study compared the cyclic fatigue resistance of nickel-titanium (NiTi) files obtained in a conventional test using a simulated canal with a newly developed method that allows the application of constant fatigue load conditions.MATERIALS AND METHODS: ProFile and K3 files of #25/.06, #30/.06, and #40/.04 were selected. Two types of testing devices were built to test their fatigue performance. The first (conventional) device prescribed curvature inside a simulated canal (C-test), the second new device exerted a constant load (L-test) whilst allowing any resulting curvature. Ten new instruments of each size and brand were tested with each device. The files were rotated until fracture and the number of cycles to failure (NCF) was determined. The NCF were subjected to one-way ANOVA and Duncan's post-hoc test for each method. Spearman's rank correlation coefficient was computed to examine any association between methods.RESULTS: Spearman's rank correlation coefficient (ρ = -0.905) showed a significant negative correlation between methods. Groups with significant difference after the L-test divided into 4 clusters, whilst the C-test gave just 2 clusters. From the L-test, considering the negative correlation of NCF, K3 gave a significantly lower fatigue resistance than ProFile as in the C-test. K3 #30/.06 showed a lower fatigue resistance than K3 #25/.06, which was not found by the C-test. Variation in fatigue test methodology resulted in different cyclic fatigue resistance rankings for various NiTi files.CONCLUSIONS: The new methodology standardized the load during fatigue testing, allowing determination fatigue behavior under constant load conditions.
Comparing the impact of various sterilization methods on the cyclic fatigue resistance, bending strength, and torsional fatigue properties of NiTi rotary files

Raid Abdullah Almnea

DOI: https://doi.org/10.1088/2053-1591/ad64ae

IF: 2.025

2024-07-18

Materials Research Express

Abstract:This study aimed to evaluate the influence of various sterilization techniques on the cyclic fatigue resistance, bending strength, and torsional fatigue resistance of Tornado Blue and Race Evo rotary endodontic file systems. Both the file systems underwent a series of 15 cycles of sterilization according to the following study groups: control group (G1; i.e., without treatment), chemical sterilization with 5.25% sodium hypochlorite (G2), dry heat sterilization (G3), glass beads sterilization (G4), and steam autoclaving (G5). Each group consisted of 8 samples (n=8/group). Statistical analysis was performed using a two-way ANOVA and Tukey's tests (p≤ 0.05). Mean values for the number of cycles between both files were 1291±52.79 rpm and 2095±52.91 rpm for Tornado Blue and Race Evo, respectively. The torsional fatigue resistance was 8.00±0.85 NCF and 10.70±0.85 NCF and the bending strength was 486.94±20.97 gf and 564.17 ±20.97 gf for Tornado Blue and Race Evo, respectively. The results showed no significant difference in the mechanical properties followed by different sterilization protocols. However, a significant difference was observed in tested properties between the two file systems (p≤ 0.05). The outcome is reassuring for clinicians that the essential process of routine sterilization at clinics seems safe with regards to mechanical integrity of the endodontic files.

materials science, multidisciplinary
Cyclic fatigue resistance of three rotary file systems in a dynamic model after immersion in sodium hypochlorite

Paulo Jorge Palma,Ana Messias,António Rosa Cerqueira,Luís Diogo Tavares,Francisco Caramelo,Luís Roseiro,João Miguel Santos

DOI: https://doi.org/10.1007/s10266-018-0401-2

Odontology

Abstract:To evaluate the effect of immersion in 3% sodium hypochlorite solution in the resistance to cyclic fatigue of three nickel-titanium (NiTi) rotary file systems, ProTaper Next (PTN), Hyflex CM (CM), and Hyflex EDM (EDM), in a mechanical model featuring axial movement. Ninety instruments of three different NiTi rotary file systems, PTN (size 25, 0.06 taper), CM (25, 0.06), and EDM (25/~, variable taper), were randomly divided according to a 3 × 3 factorial design and tested under dynamic immersion in a 3% NaOCl solution (1 or 5 min) or without immersion, making a total of 9 groups (n = 10). Files were tested in an artificial root canal with 45° angle and 5 mm radius apical curvature being submitted to back-and-forth movements until fracture. Statistical analysis was performed using two-way factorial ANOVA with Bonferroni post-hoc tests, at a significance level of 5%. Instruments were evaluated for reliability using a Weilbull approach. Regardless of the immersion treatment, PTN had on average 1200 ± 178 cycles to fracture, CM had 1949 ± 362, and EDM had 5573 ± 853, which was a significantly different (P < 0.01). The NaOCl immersion promoted a significant reduction in the mean number of cycles to fracture (P = 0.01), and was reflected in a significant reduction of the characteristic life of the instruments of the CM end EDM groups. Within this study conditions, EDM instruments performed better to cyclic fatigue followed by CM and then PTN. Immersion in NaOCl decreased the resistance to cyclic fatigue of all tested instruments, but affected more those manufactured from CM wire.
Comparative Evaluation of the Cyclic Fatigue Resistance of WaveOne Gold in Reciprocation, ProGlider in Rotary Motion, and Manual Files in a Reciprocating Handpiece Within Simulated Curved Canals: An In Vitro Study

Shivangi M Pujara,Hardik B Shah,Leena H Jobanputra

DOI: https://doi.org/10.7759/cureus.67704

2024-08-24

Cureus

Abstract:Aim This study compares the cyclic fatigue resistance of glide path files versus manual files used with a reciprocating handpiece in simulated curved canals, specifically evaluating WaveOne Gold Glider, ProGlider, stainless steel (S.S.) K files, nickel-titanium (NiTi) K files, and Flexo K files. Materials and methods Seventy-five instruments were divided into five groups of 15. Simulated canals with a 45° angle and a 5 mm radius of curvature were created using laser micromachining on S.S. blocks. A reciprocating endodontic handpiece (TEP-ER10, NSK, Japan) was used for the manual files and an X-Smart Plus endo motor for the rotary files. The time to fracture was recorded via videography. Statistical analysis was performed using analysis of variance (ANOVA) and post-hoc Tukey tests. Results Flexo files exhibited the highest mean cyclic fatigue resistance (1690.33 ± 456.97 seconds), followed by WaveOne Gold Glider (872.13 ± 210.08 seconds), NiTi K files (760.73 ± 163.86 seconds), S.S. K files (707.60 ± 257.98 seconds), and ProGlider (371.00 ± 66.02 seconds). Fragment length differences were statistically insignificant among the groups. ANOVA showed significant differences in cyclic fatigue resistance but not in fragment length. Conclusion Flexo files showed superior cyclic fatigue resistance, making them ideal for glide path formation. NiTi and S.S. K files with a reciprocating handpiece performed similarly to WaveOne Gold Glider, providing a cost-effective alternative to rotary systems, especially in resource-limited areas. ProGlider had the lowest resistance, highlighting the advantage of reciprocating motion in enhancing durability.
A Cellular Automata Model of Bond Interactions Among Molecules

L. Kier

DOI: https://doi.org/10.1021/ci000326r

2000-09-01

Journal of Chemical Information and Computer Sciences

Abstract:The ten types of alkane bonds have been modeled as isolated fragments using cellular automata dynamics. The rules governing the states and the trajectories of the cells simulating the bonds are derived from the bimolecular interaction accessibilites recently described. The sum of cell encounters at unit iteration (time) becomes a parameter associated with the relationship of a molecule with its neighbors. This value is found to correlate very closely with the boiling points of alkanes, pentanes through octanes. The results reinforce the concept that the molecular connectivity indices are describing the interaction possibilities among alkanes. The study introduces a new way of simulating intermolecular bond encounter dynamics among many molecules.
‘Serial magnetoencephalographic observations of a normally developing infant during sleep’

S. Bowyer,D. Burdette,J. Moran,N. Tepley

DOI: https://doi.org/10.1111/j.1469-8749.2000.tb00059.x

2000-02-01

Developmental Medicine & Child Neurology

Abstract:‘Serial magnetoencephalographic observations of a normally developing infant during sleep’ SIR–Magnetoencephalography (MEG) is the measurement of weak magnetic fields arising from neuronal activity in the brain. MEG has been used extensively in the evaluation of functional localization1, epileptiform activity2, and DC shifts, which arise in migraine, stroke, and other pathological conditions3–5. With the advent of large array neuromagnetometers, specifically those utilizing magnetometers that can detect relatively deeper sources, infants are easier to study. EEG has been used in the assessment of brain maturity in infants and young children. Although the waking background provides a useful marker of maturity (e.g. frequency of the posterior, dominant rhythm), waking EEG recordings in the infant are often limited by prominent muscle and movement artefacts. Sleep EEG recording provides a more consistent means of assessing infantile brain maturity6. As the brain matures, normal myelination produces an increase in faster frequencies and a decrease in the duration and amplitude of sleep spindles in EEG6,7. Weekly magnetoencephalographic measurements were performed on a normally developing infant during a longitudinal study of 47 weeks. This feasibility study was conducted to evaluate changes in brain magnetocerebral fields that accompany normal maturation in the infant. MEG recordings were made with a seven-channel superconducting neuromagnetometer (BTi model 607). MEG signals were recorded first over the left hemisphere and then over the right during each recording session. The central coil in the seven-channel array was located over the midtemporal region in the T3 position on the left (International 10–20 System of electrode placement) and the T4 position on the right. Six minutes of MEG data were collected over each hemisphere at a rate of 130 samples per channel per second, with low pass filter set at 50 Hz and high pass filter set at 0.5 Hz. Data were stored on optical disk for later analysis. A single power spectrum estimate for each 6 minutes of data was generated by averaging fast fourier transform (FFT) power spectra, which utilized an 8-second Hanning window and overlapped by 75%. To avoid amplitude changes from variations of the sensor-to-head distance, these spectral amplitudes were converted into a percentage of the total spectral power, a measure relatively independent of distance. As sleep spindles appear as early as 6 to 8 weeks postterm, we analyzed the spectral power of sleep spindles in this normally developing infant. Frontally dominant 10to 12-Hz spindles7 and central maximum 14-Hz spindles were analyzed separately. Spectral power within delta, theta, alpha, and beta bands was analyzed. Figure 1a shows the significant decrease in the theta power band observed over the 38 weeks, and Figure 1b shows a similar increase in the alpha power band. There was no significant change in the beta power, and the delta power bands were obscured by vibration artifact from the probe and gantry in the 2to 3Hz range. Sleep spindle bursts for week 19 lasted 1.6 seconds,
Torsion Property and Cyclic Fatigue Fracture Behavior of Nickel-Titanium Endodontic Instruments

YF Zheng,C Li,C Huang,LC Zhao

DOI: https://doi.org/10.4028/www.scientific.net/kem.288-289.603

2005-01-01

Key Engineering Materials

Abstract:The torsion property and rotary fatigue fracture behavior of SmartÒ K file and R reamer made of nickel titanium alloy have been studied by means of Shimadzu Autograph DDS-10T universal tester and man-made cyclic system with curved copper tubes as simulated root canal. The instrument surface and the cyclic fatigue fracture surface have been investigated by optical microscope and scanning electron microscope. Comparing with ANSI/ADA specification no.28, maximum torsion values of both SmartÒ K and R endodontic instruments are satisfied in practice. Tensile stresses on the outer surface of the endodontic instruments play a dominant role in fracture initiation during cyclic fatigue fracture. The cyclic number corresponding to cyclic fatigue fracture decreases with the increase of the instrument size number/ curvature. SmartÒ K- and R endodontic instruments exhibit good ductility characteristics, therefore superior resistance to fracture.

A Dramatic pH Effect Leads to a Catalytic Asymmetric Epoxidation.

In vitro evaluation of cyclic fatigue resistance of thermally treated novel nickel-titanium rotary instruments

Comprehensive Assessment of Cyclic Fatigue Strength in Five Multiple-File Nickel–Titanium Endodontic Systems

An Investigation of the Metal Fatigue of Different Nickel-Titanium Rotary Instruments After Prolonged Use

Characterization of a novel canine T-cell line established from a spontaneously occurring aggressive T-cell lymphoma with large granular cell morphology.

Comparison of cyclic fatigue resistance of four pediatric rotary file systems at body temperature: an in vitro study

Impact of Angle of File Access and Location of Canal Curvature on the Dynamic Cyclic Fatigue of Nickel Titanium Rotary Instruments

In Vitro Analysis of the Fatigue Resistance of Four Single File Canal Preparation Instruments

Nickel-Titanium Rotary Instruments: An In Vitro Comparison (Torsional Resistance of Two Heat-treated Reciprocating Files)

Comparative Analysis of NiTi Instruments with Different Alloy Treatments

A comparative study of cyclic fatigue of 6 endodontic systems. An in vitro study

Cyclic fatigue and torsional strength of three different thermally treated reciprocating nickel-titanium instruments

The effect of canal curvature on cyclic fatigue resistance of rotary instruments using different irrigation materials ( in vitro study)

An in vitro comparative evaluation of cyclic fatigue resistance of two rotary and two reciprocating file systems

Cyclic fatigue resistance tests of Nickel-Titanium rotary files using simulated canal and weight loading conditions

Comparing the impact of various sterilization methods on the cyclic fatigue resistance, bending strength, and torsional fatigue properties of NiTi rotary files

Cyclic fatigue resistance of three rotary file systems in a dynamic model after immersion in sodium hypochlorite

Comparative Evaluation of the Cyclic Fatigue Resistance of WaveOne Gold in Reciprocation, ProGlider in Rotary Motion, and Manual Files in a Reciprocating Handpiece Within Simulated Curved Canals: An In Vitro Study

A Cellular Automata Model of Bond Interactions Among Molecules

‘Serial magnetoencephalographic observations of a normally developing infant during sleep’

Torsion Property and Cyclic Fatigue Fracture Behavior of Nickel-Titanium Endodontic Instruments