Abstract:Background: Finishing and polishing of composite resin restorations can be considered two different procedures or two steps of a single procedure. During the finishing procedure, contours are corrected while margins and irregularities are smoothened. The polishing procedures result in the production of a smooth and lustrous finish. Consensus regarding the correct timing for initiating the steps of finishing and polishing after the curing of the composite resins is divided. Some authors support immediate finishing and polishing while other authors support delaying the finishing and polishing procedures. Aim: The aim of this study is to evaluate the surface roughness and microhardness of composite resin restoration subjected to finishing and three different polishing systems immediately and after 24 h. Materials and method: Eighty composite resin samples were prepared. A Teflon mold was made which was customized for this study having dimensions of 10-mm diameter and 2-mm depth. For the first group of specimens, Group I (n = 20) the composite resin surface was covered with Mylar Strips which acted as control. The other specimens (n = 60) were prepared without the use of a Mylar strip, followed by curing. For all the samples, curing was done with a light-emitting diode for 40 s each. Eighty light-cured samples were divided equally into 4 groups, each group containing 20 samples (n = 20). Out of the 20 samples, in the second, third, and fourth groups, (Kenda C. G. I., Shofu Super-snap X-Treme, and Eve Diacomp Plus Twist) 10 samples were finished and polished immediately after curing and the other 10 samples were finished and polished after 24 h of curing. The samples in Groups II, III, and IV were subjected to finishing by a 12-fluted tungsten carbide bur and were polished according to the respective manufacturer's instructions. The samples were then subjected to quantitative analysis of surface roughness by a noncontact three-dimensional optical profilometer (Bruker GT-Q; Ettlingen, Germany) and qualitative analysis of surface roughness by a scanning electron microscope (Zeiss EVO 18 Special Edition; Carl-Zeiss-Strasse; Oberkochen Germany) at ×10,000 magnification. The samples were also subjected to Vickers microhardness measurement using a microhardness tester (Leica VMHT 001; Walter UHL GmbH, Germany) under 100 g load over 10 s. Conclusion: A. For surface roughness: The samples cured under Mylar strips gave the least surface roughness values (0.25 ± 0.032). Immediate finishing and polishing procedures led to statistically less surface roughness than when finishing and polishing procedures were performed after a delay of 24 h for all polishing systems used B. For microhardness: The samples cured under Mylar strips gave the least microhardness values (57.1 ± 2.03). Delayed finishing and polishing increased microhardness values in all finishing and polishing systems used. Different polishing systems did not have any significant effect on the microhardness values in immediate and delayed finishing and polishing groups.

Effect of cold light bleaching on the surface micro-hardness and surface roughness of resin composites

Effects of Cold Light Bleaching on the Color Stability of Composite Resins.

Micro-Hardness and Surface Roughness of Bulk-Fill Composite Resin: Effect of Surface Sealant Application and Two Bleaching Regimens

The effect of tooth bleaching using violet LED (405-410 nm) on the properties of resin-based composites

Effect of laser irradiation during in-office tooth bleaching on surface properties of resin-based restorative materials

Changes in physical properties of universal composites and CAD/CAM materials after bleaching and antioxidant applications: Scanning electron microscope and atomic force microscope evaluation

Effect of peroxide‐free and peroxide‐based in‐office bleaching on the surface and mechanical properties of CAD/CAM esthetic restorative materials

Effect of Hydrogen Peroxide-Based Bleaching Agents on the Color Dimensions and Surface Roughness of Different Milled Restorative Dental Materials

Effects of curing time and intensity and polishing technique on color stability of bleach-shade composite resins

The effect of toothbrushing on surface gloss of resin composites

Effects of Light Attenuation through Dental Tissues on Cure Depth of Composite Resins

Surface roughness and microhardness evaluation of composite resin restorations subjected to three different polishing systems immediately and after 24 h: An in vitro study

Effect of Successive At-home Bleaching Sessions on the Surface Properties, Biaxial Flexural Strength, and Reliability of CAD-CAM Monolithic Materials

Color Stability and Staining Susceptibility of Direct Resin-Based Composites after Light-Activated In-Office Bleaching

Effect of polishing on surface roughness and surface-free energy of direct tooth-colored restorative materials

Effects of light-curing modes on the polymerization shrinkage and surface hardness of composite resins]

The Effects of Intensity, Exposure Time, and Distance of Polymerization Light on Vickers Microhardness and Temperature Rise of Conventional Resin-Based Composite

Comparisons of effects of different polishing systems on PFM and composite resin surfaces

Effects of Different Concentrations of Carbamide Peroxide on Color, Surface Roughness, and Hardness of CAD/CAM Dental Ceramics

An In Vitro Comparative Evaluation of the Effects of Different Bleaching Agents on Marginal Integrity of Two Different Restorative Resin Materials: An Analysis by Confocal Laser Microscopy

An In Vitro Investigation Of Wear Resistance And Hardness Of Composite Resins