Abstract:IntroductionIn this study, the silk fibroin blended constructs were produced, scaffold performances of different kinds of scaffold were analyzed, and the better type for tissue engineering was optimized.MethodsThe silk fibroin/collagen (SF/C) and silk fibroin/chitosan (SF/CS) were made using a freeze-drying technique, porosity, water absorption expansion rate, mechanical properties and pore size of different scaffold was detected. Bone marrow mesenchymal stem cells (BMSCs) of 4-week-old male Wistar rats were separated by density gradient centrifugation, third generation BMSCs were seeded onto scaffolds, cultured 14 days, proliferation and metabolize of cells were detected in different time using the thiazolyl blue tetrazolium bromide (MTT) assay method, and cell morphology and distribution were observed by histological analysis and scanning electron microscopy (SEM).ResultsPorosity, water absorption expansion rate and Young’s modulus of SF/C were significantly higher than SF/CS (p < 0.05); pore size of SF/C and SF/CS was 103 ± 12 and 76 ± 11 μm and had no significant differences between two types (p > 0.05); MTT results showed that the metabolism of cells in the SF/C was better than SF/CS; after cultivation for 14 days, in the inner zone of scaffolds, cells staining were little or absent from SF/CS, lots of cells staining were existing in SF/C; pore size was consistent, holes communicated with each other better, stem cells grew well inside the scaffolds, extended fully and secreted much extracellular matrix under SEM in SF/C scaffold; internal structure of SF/CS was disorder, holes size were not consistent, and did not communicated with each other and cells were partly dead.ConclusionCompared with SF/CS, SF/C scaffold showed better porosity, water absorption expansion rate, elasticity modulus and pore size, cells grow well inside the scaffolds, and was more suitable for tissue engineering.

Feasible Application of Collagen-Chitosan 3-D Scaffolds in Tissue Engineering Blood Vessel Research

Fabrication of a tubular vascular scaffold with circumferential microchannels to induce oriented growth of smooth muscle cells

From Common Biomass Materials to High-Performance Tissue Engineering Scaffold: Biomimetic Preparation, Properties Characterization, in Vitro and in Vivo Evaluations

Initial Investigation of Novel Human-Like Collagen/chitosan Scaffold for Vascular Tissue Engineering.

Primary Experimental Study on the Construction of Tissue Engineering Blood Vessel

A Sandwich Tubular Scaffold Derived from Chitosan for Blood Vessel Tissue Engineering

Preparation of recombinant human-like collagen/fibroin scaffold and its promoting effect on vascular cells biocompatibility

A Biological 3D Printer for the Preparation of Tissue Engineering Micro-Channel Scaffold

Silk fibroin/collagen and silk fibroin/chitosan blended three-dimensional scaffolds for tissue engineering

Mechanical Enhancement and in Vitro Biocompatibility of Nanofibrous Collagen-Chitosan Scaffolds for Tissue Engineering

3D printed GelMA/carboxymethyl chitosan composite scaffolds for vasculogenesis

Potential of 3-D tissue constructs engineered from bovine chondrocytes/silk fibroin-chitosan for in vitro cartilage tissue engineering

The fabrication and cell culture of three-dimensional rolled scaffolds with complex micro-architectures.

Biomaterial Scaffolds with Biomimetic Fluidic Channels for Hepatocyte Culture

Production of Composite Scaffold Containing Silk Fibroin, Chitosan, and Gelatin for 3D Cell Culture and Bone Tissue Regeneration.

Fabrication and Characterization of Chitosan/gelatin Porous Scaffolds with Predefined Internal Microstructures

Low-temperature 3D printing of collagen and chitosan composite for tissue engineering

Bioprinted Chitosan and Hydroxyapatite Micro-Channels Structures Scaffold for Vascularization of Bone Regeneration

Fabrication and Assessment of Chondroitin Sulfate-Modified Collagen Nanofibers for Small-Diameter Vascular Tissue Engineering Applications.

Fabrication and Characterization of Poly(l-Lactide-co-glycolide) Knitted Mesh-Reinforced Collagen–chitosan Hybrid Scaffolds for Dermal Tissue Engineering

Coaxial 3D Bioprinting Process Research and Performance Tests on Vascular Scaffolds