Abstract:As a step towards developing a finite element model of the knee that can be used to study how the variables associated with a meniscal replacement affect tibio-femoral contact, the goals of this study were 1) to develop a geometrically accurate three-dimensional solid model of the knee joint with special attention given to the menisci and articular cartilage, 2) to determine to what extent bony deformations affect contact behavior, and 3) to determine whether constraining rotations other than flexion/extension affects the contact behavior of the joint during compressive loading. The model included both the cortical and trabecular bone of the femur and tibia, articular cartilage of the femoral condyles and tibial plateau, both the medial and lateral menisci with their horn attachments, the transverse ligament, the anterior cruciate ligament, and the medial collateral ligament. The solid models for the menisci and articular cartilage were created from surface scans provided by a noncontacting, laser-based, three-dimensional coordinate digitizing system with an root mean squared error (RMSE) of less than 8 microns. Solid models of both the tibia and femur were created from CT images, except for the most proximal surface of the tibia and most distal surface of the femur which were created with the three-dimensional coordinate digitizing system. The constitutive relation of the menisci treated the tissue as transversely isotropic and linearly elastic. Under the application of an 800 N compressive load at 0 degrees of flexion, six contact variables in each compartment (ie., medial and lateral) were computed including maximum pressure, mean pressure, contact area, total contact force, and coordinates of the center of pressure. Convergence of the finite element solution was studied using three mesh sizes ranging from an average element size of 5 mm by 5 mm to 1 mm by 1 mm. The solution was considered converged for an average element size of 2 mm by 2 mm. Using this mesh size, finite element solutions for rigid versus deformable bones indicated that none of the contact variables changed by more than 2% when the femur and tibia were treated as rigid. However, differences in contact variables as large as 19% occurred when rotations other than flexion/extension were constrained. The largest difference was in the maximum pressure. Among the principal conclusions of the study are that accurate finite element solutions of tibio-femoral contact behavior can be obtained by treating the bones as rigid. However, unrealistic constraints on rotations other than flexion/extension can result in relatively large errors in contact variables.

The Biomechanical Responses of Knee Joint to Foot Supports:Computational Simulation of the Lower Limb

Biomechanical response of lower limb joints to lateral wedge insoles

A Finite Element 3d Model Of In Vivo Human Knee Joint Based On Mri For The Tibiofemoral Joint Contact Analysis

An in Vitro and Finite Element Study of Load Redistribution in the Midfoot.

Finite element analysis of in vivo tibio-femoral contact features with menisci

Modulation of Internal Tissue Stresses of the Knee Via Control of Variable-Stiffness Properties in a 3D-Printed Footwear: A Combined Experimental and Finite Element Analysis

In Vivo Biomechanical Dynamic Simulation of a Healthy Knee During the Single-leg Lunge and Its in Vitro Experiment Validation

A Quasi-Dynamic Nonlinear Finite Element Model to Investigate Prosthetic Interface Stresses During Walking for Trans-Tibial Amputees

Prediction of in vivo joint mechanics of an artificial knee implant using rigid multi-body dynamics with elastic contacts.

In vivo biomechanical dynamic simulation of a healthy knee during the single-leg lunge and its experiment validation

Integrated Modeling Framework to Guide Novel Insole Designs for Stress Redistribution at the Human Knee Joint.

Musculoskeletal model of the lower extremity of trans-tibial amputee

Influence of arch support heights on the internal foot mechanics of flatfoot during walking: A muscle-driven finite element analysis

A three-dimensional finite element foot-ankle model and its personalisation methods analysis

Multiscale finite element musculoskeletal model for intact knee dynamics

[Inertial Effects on Interface Pressure Between Prosthetic Socket and Residual Limb].

Effect of Gait Changes on Tibio-Femoral Joint Contact Biomechanics

A finite element model of the lower limb during stance phase of gait cycle including the muscle forces

A finite element model of the human knee joint for the study of tibio-femoral contact

The Investigation on a Quasi-Dynamic Finite Element Model to Predict Interface Pressure on Below-Knee Residual Limb

The effect of including a mobile arch, toe joint, and joint coupling on predictive neuromuscular simulations of human walking