Abstract:Total knee arthroplasty (TKA) is a cornerstone in addressing knee joint disorders, significantly enhancing patients' quality of life. However, despite technological advancements, a comprehensive understanding of the dynamic stresses experienced by knee prostheses during daily activities, particularly under rehabilitation interventions, remains elusive. This study aims to bridge this gap by employing numerical simulations and finite element analysis to elucidate these dynamic stresses and their interaction with rehabilitation protocols. A real-life knee replacement prosthesis model was meticulously constructed through coordinate measuring and 3D scanning, facilitating detailed finite element analysis in ANSYS Workbench version 17.1. Two distinct boundary conditions and loading scenarios were applied, with comparisons made between linear and nonlinear material assumptions. The simulation results using these different boundary condition methods revealed minimal differences. Specifically, at a knee angle of 0°, the relative stress error rate between the two boundary condition types was approximately 1 % (1.11 MPa and 1.099 MPa, respectively). At 15° and 90°, the error rates were 1.9 % and 0.56 %, respectively (10.275 MPa and 10.078 MPa at 15°; 10.275 MPa and 10.078 MPa at 90°). Given these minimal differences, the first type of boundary condition was adopted for the subsequent scenarios to enhance convergence efficiency in the analysis. Moreover, comparative analyses between linear and nonlinear material behaviors demonstrated acceptable agreement, offering insights into potential efficiency gains in simulation methodologies. Building on this foundation, an optimized tibial model was proposed, incorporating geometric alterations to the tray. Quantitative assessments revealed significant reductions, with von Mises stress decreasing by 23.35 % and equivalent strain by 17 % at a knee angle of 140°. Further evaluations at varying angles, including 60°, consistently showed positive influences on stress and strain. These quantitative findings not only contribute valuable insights into the mechanical behavior of knee prostheses but also provide tangible evidence for the efficacy of linear material behavior assumptions. The proposed optimized model exhibits promising potential for enhancing the design and performance of knee prostheses, particularly under critical loading conditions. In conclusion, these results underscore the importance of a nuanced understanding of knee prosthesis behavior during rehabilitation, offering a quantitative foundation for refining existing designs and informing the development of next-generation prostheses.

Integrated Modeling Framework to Guide Novel Insole Designs for Stress Redistribution at the Human Knee Joint.

Biomechanical Design of Lightweight Full Contacted Insole Based on Structural Anisotropy Bespoke

Modulation of Internal Tissue Stresses of the Knee Via Control of Variable-Stiffness Properties in a 3D-Printed Footwear: A Combined Experimental and Finite Element Analysis

Customized Design for Ergonomic Products Via Additive Manufacturing Considering Joint Biomechanics

Plantar Pressure Relief under the Metatarsal Heads – Therapeutic Insole Design Using Three-Dimensional Finite Element Model of the Foot

In-silico techniques to inform and improve the personalized prescription of shoe insoles

Development of Customized Insole Design Framework Based on Digital Twin

The Effect of Arch Height and Material Hardness of Personalized Insole on Correction and Tissues of Flatfoot

A Three-Dimensional Printed Foot Orthosis for Flexible Flatfoot: An Exploratory Biomechanical Study on Arch Support Reinforcement and Undercut

Influence of foot posture on immediate biomechanical responses during walking to variable-stiffness supported lateral wedge insole designs

An apparatus to quantify anteroposterior and mediolateral shear reduction in shoe insoles.

Design and evaluation of a wedge-shaped adaptive knee orthosis for the human lower limbs

Different Design Feature Combinations of Flatfoot Orthosis on Plantar Fascia Strain and Plantar Pressure: A Muscle-Driven Finite Element Analysis With Taguchi Method

Effect of Custom-designed Insole with Arch and Metatarsal Support on Adjustment of the Lower Limb Kinematics

Novel insole design for diabetic foot ulcer management

Numerical investigation of knee prosthesis stresses in daily activities: Insight into knee rehabilitation and Creation of a new optimal model

Manufacturing and finite element assessment of a novel pressure reducing insole for Diabetic Neuropathic patients

Parametric modeling and performance analysis of a personalized insole based on 3D scanning and selective laser sintering

Footwear Design for Hallux Valgus: A Virtual Prototyping with Finite Element Modeling

Biomechanical Analysis of the FlatFoot with Different 3D-Printed Insoles on the Lower Extremities

A Study on the Effects of Lateral-Wedge Insoles on Plantar-Pressure Pattern for Medial Knee Osteoarthritis Using the Wearable Sensing Insole