Abstract:The airflow distribution chamber is an important part of the air-impingement jet dryer. Non-uniform distribution of airflow field can cause inconsistence of materials quality, prolong the drying process and consume more energy. Therefore, it is essential to optimize the flow field structure. However, the traditional way of design-manufacture-further improvements requires long transformation time, high costs and the measurement range is usually disappointing. Computational Fluid Dynamics (CFD) can provide detailed information on airflow patterns and ensure convenient design of agricultural equipments. In this paper, the Computational Fluid Dynamics (CFD) was first used to simulate the inner flow of structures similar to airflow distribution chamber based on the differential equation and RNG k-εturbulence model. The original structure was a cuboid and the inlet boundary was set to velocity-inlet. The speed deviation ratio(E) and the non-uniformity coefficient(M) were chosen as comprehensive evaluation indicators. The velocity and pressure distributions in chamber flow field were obtained and used to analyze the improved designs based on the original structure. They were inclination models, semi-cylindrical models and flat vortex models. The simulation results indicated that two symmetrical reverse vortex zones were formed in original structure, which led to the nozzle exit velocity first decreases and then increases along the height direction. The airflow velocity of round nozzles ranged from 11.9 to 17.7 m/s under the design condition and the minimum value was got in the eighth row. The E and M values of original structure was calculated to be 24.6% and 18.1%, respectively. This illustrates that the original structure was far from perfect. Decreasing the width of chamber bottom could not improve the distribution of airflow field, while the spoiler models were proved feasible. The flat vortex models built a greater effect on the optimization of airflow distribution than semi-cylindrical models. And the E and M values of the flat models dramatically decreased. It maybe because several uniform vortex zones formed between flats, which had a positive impact on airflow distribution. The optimum solution was got under the flat vortex model with 160 mm and 14 mm as the value of the plate-to-plate distance and the height difference, respectively. Moreover, the airflow velocity merely ranged from 13.1 to 15.3 m/s. The distribution trend of simulation results showed little difference compared to the experiment data. The maximum relative error under different conditions changed from 4.2% to 8% showing an increasing trend as mass flow increased. The results provide a reference for the uniformity design of structures similar to the airflow distribution chamber.

Organizing Analysis Method of Air Curtain Fitting for Engineering Device and Testing

Analysis of the Flow Characteristics of Diffuser/Nozzle Based on MEMS

Application of CFD Analytical Method on Checking Design and Optimization

CFD ANALYSIS ON FLOW CHARACTERISTICS OF PERFORATED PLATE IN MULTI-STAGE HIGH PRESSURE REDUCING VALVE

Analysis on Control System of Transport Aircraft Cabin Door's Electrohydraulic System in Virtual Flow

Determination of Critical Air Ratio and Performance Study of a New Air Curtain Fume Hood

Computed fluid dynamic design of the air curtain for open display case

Simulationand Analysis of the Internal Flow Field for Critical Flow Venturi Nozzles Based on Fluent

Flow Analysis and Optimization of the Air channel of Drying Chamber Based on CFD

CFD Analysis on Wind Chamber Test-Bed for Automobile Heat Exchanger

Analysis of Flow and Heat Characteristics of Seal Structure with Gap and Cavity Under the Impact of High Speed Airflow

The Analysis of Airflow in the Chamber-Rotating Structure

Analysis about temperature and flow field based on high/low temperature air conditions of docking test system

Air curtain dust-collecting technology: Influence factors for air curtain performance

Structure Design and Optimizing Simulation of a New Type Closing-to-wall Air Device

Flow Field Simulation Analysis of Air Arc Chamber in Low Voltage Apparatus

Experimental study of the factors influencing the uniformity of an air curtain and numerical simulation of the factors influencing its dust barrier effect

STUDY ON NUMERICAL SIMULATION OF A NEW TYPE OF ROTARY AIR CURTAIN EXHAUST HOOD

Numerical simulation and optimum design on airflow distribution chamber of air-impingement jet dryer

Application and Design of Air Curtain System in the Connected Channel Between the Metro and Mall

Research on Flow Divider of High Pressure Water-Jet Target Material Detection Device