Abstract:Although body-centered cubic (BCC) structural magnesium-lithium (Mg-Li) alloys have lower density and better formability than common hexagonal close-packed (HCP) Mg alloys, their applications remain limited due to their low strength. The purpose of this study is to investigate the effect of Y/Er and Zn addition on the microstructure and tensile properties of Mg-11Li alloy with a BCC structural matrix by comparing Mg-11Li, Mg-11Li-4Y-2Er-2Zn, and Mg-11Li-8Y-4Er-4Zn (wt %) alloys. The results indicate that the addition of Y/Er and Zn at a ratio of 3:1 cannot promote the formation of long-period stacking ordered structure in Mg-11Li alloy such as that in Mg-Y-Er-Zn alloys and the dominant intermetallic phases formed are BCC Mg24RE5 and face-centered cubic (FCC) Mg3RE2Zn3 phases. With an increase of the content of Y/Er and Zn in an as-cast alloy, the fraction of intermetallic particles increases and the grain size decreases. The addition of Y/Er, as well as Zn, dramatically promotes the refinement of dynamic recrystallization (DRX) during extrusion. The initial intermetallic phases induced by Y/Er and Zn addition are broken into relatively fine particles during extrusion, and this contributes to refining the dynamic recrystallized (DRXed) grains mainly by the particle stimulated nucleation mechanism. The as-extruded Mg-11Li-4Y-2Er-2Zn and Mg-11Li-8Y-4Er-4Zn alloys exhibit much higher tensile strength as compared with as-extruded Mg-11Li alloy, which is mainly ascribed to the refined DRXed grains and numerous dispersed intermetallic phase particles. It is suggested that further refinement of intermetallic particles in these extruded Mg-11Li-based alloys may lead to higher quality alloy materials with low density and excellent mechanical properties.

Effect of Zn and Y on microstructures and properties of normally-solidified Mg-Zn-Y alloys

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure and Phase Transformation of Forged Mg–3.7Zn–0.3Y–0.3Gd Quasicrystal Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

A Near-bulk Quasicrystal Alloy Formed in Zn-Mg-Y System

Microstructure and Precipitates in Mg-Zn-Y Alloys

Study on phase constitutions, growth pattern and mechanical properties of Mg-1.4Gd-1.2Y-xZn-0.15Zr (at%) alloys

Microstructure and phase transformation of as-cast and annealed Mg–4Zn–1Y alloy containing quasi-crystal phase

The Effect of Y/Er and Zn Addition on the Microstructure and Mechanical Properties of Mg-11Li Alloy

Quasicrystal-reinforced Mg alloys

Effect of Zn/(Gd+Y) ratio on the microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy

Effect of quasicrystal and Laves phases on strength and ductility of as-extruded and heat treated Mg–Zn–Gd-based alloys

Simulation on Microstructure Evolution and Mechanical Properties of Mg−Y Alloys: Effect of Trace Y

Influence of Zn Content on Microstructure and Tensile Properties of Mg–Zn–Y–Nd Alloy

Microstructure, generation of intermetallic compounds and mechanical strengthening mechanism of as-cast Mg–4Y–xZn alloys

The Effect of Gd and Zn Additions on Microstructures and Mechanical Properties of Mg-4sm-3nd-Zr Alloy

Effect of Ca Concentration on Microstructure and Mechanical Properties of As-Cast and As-Extruded Quasicrystal-Strengthened Mg-7.2Zn-2.4Gd Alloy

Effect of Icosahedral Phase on Crystallographic Texture and Mechanical Anisotropy of Mg–4%Li Based Alloys

Effect of yttrium addition on dynamic mechanical properties, microstructure, and fracture behavior of extrusion-shear ZC61 + xY (x = 0, 1, 2, 3) alloys

Influence of Zr addition on the morphology of primary MgZn 2 in the solidification microstructure of Zn-6Al-3Mg alloy