Abstract:Laser-welded Ti-6Al-4 V is prone to severe residual stresses, microstructural variation, and structural defects which are known detrimental to the mechanical properties of weld joints. Residual stress removal is typically applied to weld joints for engineering purposes via heat treatment, in order to avoid premature failure and performance degradation. In the present work, we found that proper welding residual stresses in laser-welded Ti-6Al-4 V sheets can maintain better ductility during uniaxial tension, as opposed to the stress-relieved counterparts. A detailed experimental investigation has been performed on the deformation behaviours of Ti-6Al-4 V butt welds, including residual stress distribution characterizations by focused ion beam ring-coring coupled with digital image correlation (FIB-DIC), X-ray computerized tomography (CT) for internal voids, and in-situ DIC analysis of the subregional strain evolutions. It was found that the pores preferentially distributed near the fusion zone (FZ) boundary, where the compressive residual stress was up to-330 MPa. The removal of residual stress resulted in a changed failure initiation site from the base material to the FZ boundary, the former with ductile and the latter with brittle fracture characteristics under tensile deformation. The combined effects of residual stresses, microstructures, and internal pores on the mechanical responses are discussed in detail. This work highlights the importance of inevitable residual stress and pores in laser weld pieces, leading to key insights for post-welding treatment and service performance evaluations. (c) 2024 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

Finite Element Analysis of Laser Welding Residual Stress and Distortion in Welded Joints of TC4 Titanium Alloy

Effects of heat input on laser welding residual stress and distortion of TC4 titanium alloy

Numerical Simulation of the Residual Stress in Laser Beam Welded and TIG Welded Joints of Thin Plate of Titanium Alloy

Numerical and Experimental Analysis of Residual Stresses in Full-Penetration Laser Beam Welding of Ti6Al4V Alloy

Study of effect on tensile stress test from distortion of fibre laser welded Ti6Al4V using FEA

Numerical Research on the Weld Bead Geometry and Residual Stresses with Different Heat Source Models in Laser Welding of Tc4 Titanium Alloy

Simulation and Analysis on Longitudinal TIG Welding of TC4 Titanium Alloy Thin-walled Circular Tube

Numerical and Experimental Investigation of Thermal Stress Distribution in Laser Lap Welding of Ti6Al4V and 2024 Alloy Plates

Effect of Laser Heat Input on Microstructure and Fatigue Behavior of TC17 Titanium Alloy Laser Welded Joint

High Gradient Residual Stresses During Laser Deep Penetration Welding of Titanium Alloy

Finite-element inverse analysis of residual stress for laser welding based on a contour method

Numerical Simulation for Full-Penetration Electron Beam Welding of Ti2AlNb Alloy

Numerical simulation of residual stress and deformation on laser welding of "grooved-coat" structure

Residual Welding Stresses in Laser Beam and Tungsten Inert Gas Weldments of Titanium Alloy

Numerical Simulation of Residual Stress for Laser Welding of Ti-6Al-4V Alloy Considering Solid-State Phase Transformation

Experimental and numerical study on microstructure and mechanical properties for laser welding-brazing of TC4 Titanium alloy and 304 stainless steel with Cu-base filler metal

Finite Element Analysis of Residual Stress in Laser Cladding Remanufacturing of Titanium Alloy

Effect of welding heat input on microstructure and properties of TC4 titanium alloy ultra-narrow gap welded joint by laser welding with filler wire

Numerical Simulation and Experimental Investigation of Residual Stresses and Distortions in Pulsed Laser Welding of Hastelloy C-276 Thin Sheets

Combined Effects of Local Residual Stresses, Internal Pores, and Microstructures on the Mechanical Properties of Laser-Welded Ti-6Al-4V Sheets

Effect of Underfill Defects on Distortion and Tensile Properties of Ti-2Al-1.5Mn Welded Joint by Pulsed Laser Beam Welding