Abstract:Uniaxial thermal compression of the super austenitic stainless steel Sanicro35. The thermal deformation behavior was investigated under the conditions of 900~1150 °C deformation temperature and 0.001~10 s-1 strain rate. The microstructure of the large deformation zone of the specimen was investigated using electron backscatter diffraction (EBSD). The results show that the thermal compression rheological stress of the super austenitic stainless steel Sanicro 35 decreases with increasing temperature and decreasing strain rate. Dynamic recrystallization (DRX) is the main softening mechanism for this material. The analysis of the microstructure by EBSD on the morphological features, recrystallization fraction, dislocation density and twin boundary distribution can be found that the higher grain boundary mobility drives the DRX grains to grow with the deformation temperature increases. As the strain rate increases, the larger deformation storage energy provides sufficient activation energy for DRX grain nucleation, and the nucleation of DRX grains becomes denser. The twin boundaries are mainly distributed within the DRX grains. The smaller the grain size of DRX, the denser the nucleation of twin boundaries, and the generation of twins can promote the development of DRX. The softening mechanism under most deformation conditions is discontinuous dynamic recrystallization (DDRX). However, at a strain rate of 10 s-1, the high strain rate causes microbands to be generated within the deformed grains, and the microband boundaries evolve toward the high-angle grain boundaries (HAGBs) with increasing temperature, which promotes the occurrence of Continuous dynamic recrystallization (CDRX), and the dynamic softening mechanism is the coexistence of DDRX and CDRX. The results of the study show that the reasonable hot working deformation region is: temperature of 1050-1150 °C and strain rate of 10 s-1.

Research Progress of Austenitic Heat Resistant Steel Sanicro25 Used in Ultra Supercritical Unit

Revealing the Effect of O2, SO2 and H2O in Supercritical CO2 on the Corrosion Behavior of 316L Steel at Elevated Temperature

Research Progress on High-Temperature Microstructure and Property Evolution of Super304H Austenitic Stainless Steel

Research Progress on Intergranular Corrosion Resistance of Super304H Austenite Stainless Steel

Investigation of Fireside Corrosion of Austenitic Heat-Resistant Steel 10cr18ni9cu3nbn in Ultra-Supercritical Power Plants

Research Progress of HR3C Heat Resistant Steel Used in Ultra Supercritical Boiler

The Effects of Co and W on Structural Stability and Mechanical Properties of Austenitic Heat-Resistant Steel Sanicro 25: A First-Principle Study

Research Progress on High-temperature Oxidation of Austenitic Stainless Steel for Ultra-superCritical Boilers

Multiphase Strengthening of Nanosized Precipitates in a Cost‐Effective Austenitic Heat‐Resistant Steel

Corrosion and Carburization Behavior of Heat-Resistant Steels in a High-Temperature Supercritical Carbon Dioxide Environment

Intergranular corrosion susceptibility of a novel Super304H stainless steel

Thermal deformation behavior and microstructure analysis of the as-cast super austenitic stainless steel Sanicro35

Effect of Shot-Peening on Corrosion Behavior of Austenitic Steel in Supercritical Carbon Dioxide at 700 °C

Field Studies of Steam Oxidation Behavior of Austenitic Heat-Resistant Steel 10Cr18ni9cu3nbn

Microstructures and Mechanical Properties of a Newly Developed Austenitic Heat Resistant Steel

Microstructure Characteristics and Their Effects on the Mechanical Properties of As-Served HR3C Heat-Resistant Steel

Studies on High Temperature Corrosion of Austenitic Heat‐Resistant Steels Super 304H/10Cr18Ni9Cu3NbN in Simulated and Real Combustion Gas Atmospheres

High-temperature corrosion data and mechanisms for T122, Super304H and HR3C after 15 years in 1000MW ultra-supercritical power plant

Research on the Application of Thermoelectric Potential Technology in Austenitic Heat-resistant Steel During Aging

Microstructure Impacts on Mechanical Properties in a High Temperature Austenitic Stainless Steel

Research on a Surface Shot Peeling Process for Increasing the Anti-Oxidation Property of Super304H Steel in High-Temperature Steam