Abstract:While the addition of WC increases the hardness and wear resistance of coatings, an excessive WC content can also induce crack initiation and propagation, increasing brittleness and leading to premature failure. Therefore, in this study, WC particles were incorporated into nickel-based coatings by plasma-arc surfacing to optimize their content and distribution, balancing their tensile properties and wear resistance. The coatings were comprehensively evaluated through microstructural analysis, hardness testing, wear resistance assessment, and tensile testing. The results show that as the mass fraction of WC increased from 45% to 65%, the increase in carbon significantly promoted the formation of M7C3, M6C, and M23C6 carbides and suppressed the formation of the γ-phase. The microstructural analysis showed that the content of massive carbides increased significantly with the increasing WC content, and the XPS analysis further confirmed that the changes in the WC and Cr7C3 phases were particularly pronounced in the high-WC coating. The 65% WC coating showed higher hardness (a 232 increase in HV1.0), a lower and more stable coefficient of friction (0.42), and better wear resistance than the 45% WC coating, with a wear rate of 3.329 × 10−6 mm3/(N·m)−1, which was 3.709 × 10−6 mm3/(N·m)−1 lower than that of the 45% WC coating. The conventional tensile test results show that the maximum stress and strain of the 45% WC coating were 71% and 36% higher than those of the 65% WC coating, respectively. In addition, the 45% WC coating exhibited better ductility and quasi-cleavage characteristics, whereas the 65% WC coating showed typical brittle cracking behavior. The results of the field tensile tests also showed that the fracture time of the 65% WC coating was 27 s shorter than that of the 45% WC coating. Overall, the 45% WC coating had a good combination of strength and toughness.

Preparation and Performance of Gradient WC Reinforced NiCrBSi Alloy Coating Based on Flexible Metallic Cloth Technique

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Preparation of WC Reinforced Co-Based Alloy Gradient Coatings on a H13 Mold Steel Substrate by Laser Cladding

Preparation of WC/Ni Flexible Cloth Coating by Vacuum Brazing

Preparation,Microstructure and Performance of WC-Ni Reinforced Fe-based Graded Coating

Optimizing Wear Resistance and Tensile Strength of Nickel-Based Coatings through Tungsten Carbide Reinforcement

Enhanced Adherence, Brittleness, Corrosion, and Sliding Wear by Adding NiCrFeBSiC-Mo on WC-Co Coatings and Hardened Substrates

Fabrication of gradient WC-Ni cemented carbide materials by high gravity-assisted combustion synthesis and infiltration

Preparation and electrochemical properties of gradient CrNx coatings on H13 steel

Microstructure and properties of Ni-WC gradient composite coating prepared by laser cladding

Achievement of comprehensive wear and thermal property of cold spayed CuCrZr coating via gradient structure design

Role of the nitrogen ratio on mechanical properties and wear resistance of CrN/Fe functionally graded coating produced by double glow plasma alloying

Realizing excellent tribological properties of BCC/FCC gradient high -entropy alloy coating via an in-situ interface reaction

Microstructure and Properties of CoCrFeNi(WC) High-Entropy Alloy Coatings Prepared Using Mechanical Alloying and Hot Pressing Sintering

On the adhesion performance of gradient-structured Ni–P metallic coatings

In-situ Ti(C, N) reinforced AlCoCrFeNiSi-based high entropy alloy coating with functional gradient double-layer structure fabricated by laser cladding

Microstructure and tribological behavior of CoCrFeNiMo 0.2 /SiC high-entropy alloy gradient composite coating prepared by laser cladding

Microstructure and Properties of Nickel-Based Gradient Coatings Prepared Using Cold Spraying Combined with Laser Cladding Methods

Microstructure and Properties of FeMnCrAl/Ni Coated WC Coatings Deposited by High Velocity Arc Spraying

Microstructure and wear behavior of WC-reinforced AlCoCrFeNiSi high entropy alloy coatings prepared by high-velocity arc spraying

Formation Kinetics and Properties of CrNx/H13 Functionally Graded Coating Fabricated by PVD