Abstract:Carbon nanotube/continuous carbon fiber reinforced poly(ethylene terephthalate) (CNT/CCF/PET) composites are prepared by melt impregnating. The effects of CF and CNT content on the mechanical properties, melt and crystallization behaviors, and submicroscopic morphology of CNT/CCF/PET composites are studied. The tensile test results show that the increase of CF and the addition of appropriate amount of CNT improved the tensile strength and tensile modulus of the composites. When the content of CNT is 1.0 wt% and the content of CF is 56 wt%, the properties of the composites are the best, with tensile strength of 1728.7 MPa and tensile modulus of 25.1 GPa, which is much higher than that of traditional resin matrix composites. The results of dynamic mechanical analysis (DMA) show that the storage modulus of the composites increased with the increase of CF and CNT content. In particular, the addition of CNT greatly reduced the loss modulus of the composites. Morphological analysis show that the addition of CNT improved the fiber–matrix interface of the composite, which changes from fiber pull-out and fracture failure to fiber matrix fracture failure, and the fiber matrix interface is firmly bonded. In addition, there are polymer coated CNT protrusions on the surface of the fiber was observed. The results of differential scanning calorimetry (DSC) show that the melting temperature and crystallization temperature of the composites increased with the increase of CF content. The addition of CNT had little effect on the melting temperature of the composites, but it further improved the crystallization temperature of the composites. The effect of CNT content on the crystallization kinetics of the composites is studied. The non-isothermal crystallization kinetics of the composites is described by Jeziorny's improved Avrami equation. The results show that CNT has a great influence on the crystallization type of the composites. As a nucleating agent, CNT has obvious heterogeneous nucleation effect in the composites, which improves the crystallization rate of PET.

Study on Microstructure and Mechanical Properties of Carbon/Carbon Composite Obtained by Chemical Vapor Infiltration

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Effect of chemical vapor infiltration on the flexural properties of C/C-SiC composites prepared by the precursor infiltration pyrolysis method

Preparation and characterization of carbon felt/carbon composites by chemical vapor infiltration process

Mechanical and thermal conduction properties of carbon/carbon composites with different carbon matrix microstructures

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

Microstructure and mechanical properties of 3D Cf/SiBCN composites fabricated by polymer infiltration and pyrolysis

Multi-walled carbon nanotube-based carbon/carbon composites with three-dimensional network structures.

Mechanical properties of C/C composites processed by wet impregnation and P-CVI methods

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Fabrication and mechanical properties of in situ prepared mesocarbon microbead/carbon nanotube composites

Effect of microstructure evaluation during the PIP process on macroscopic properties of C/C composites

Study on Microstructures of 2D and 3D Chemical Vapor Infiltration SiC/SiC Composites

Epitaxial Grown Carbon Nanotubes Reinforced Pyrocarbon Matrix in C/C Composites with Improved Mechanical Properties

Preparation, microstructure and properties of three-dimensional carbon/carbon composites withhigh thermal conductivity

Microstructures and properties of C/C–SiC composites derived from different gaseous carbon matrix precursors

Characterization of the Microstructure of Three‐Dimensional‐Needled Carbon/Silicon Carbide Composites

Correlation of the permeability and porosity development of carbon/carbon composites during pyrolysis

LASER RAMAN MICROSPECTROSCOPY STUDY ON MICROSTRUCTURE OF C/C COMPOSITES

Preparation and structure analysis of carbon/carbon composite made from phenolic resin impregnation into exfoliated graphite

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites