Abstract:We aimed to investigate the corrosion patterns and the main controlling factors of N80 steel and P110 steel tubing under different sections. Conducting weight loss corrosion experiments for 168 h using high-temperature and high-pressure autoclaves to simulate the corrosion behavior of two types of casing materials, N80 steel and P110 steel, in different well sections under specific conditions of CO2 content, chloride ion concentration, temperature, pressure, and sulfate-reducing bacteria population in highly mineralized formation water. X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to analyze the corrosion products, surface morphology, and elemental composition of the two steel pipes. Additionally, 3D microscopy was employed to observe the morphology and measure the dimensions of localized corrosion pits. Under different well sections, the corrosion products formed on N80 steel and P110 steel mainly consist of FeCO3, and crystalline salts of chlorides present in the solution medium. Under low-water-cut conditions, narrow and deep corrosion defects were observed, while narrow and shallow corrosion defects were found under high-water-cut conditions. In the upper wellbore section, both steel pipes exhibited dispersed and thin corrosion product films that suffered from rupture and detachment, resulting in severe localized corrosion. In the middle wellbore section, the corrosion product film on N80 steel comprised irregularly arranged polygonal grains, some of which exhibited significant gaps, leading to extremely severe corrosion. For P110 steel, the corrosion product film was also dispersed and thin, with extensive detachment and extremely severe corrosion. In the lower wellbore section, both steel pipes were covered with a dense layer of grains, with smaller gaps between them, effectively protecting the metal matrix from corrosion. Consequently, the corrosion rate decreased compared to the middle section but still exhibited severe corrosion. In low-water-cut conditions, attention should be given to the risk of column safety due to corrosion from condensate water and CO2, as well as the size of narrow and deep corrosion defects in the middle wellbore section. In high-water-cut conditions, it is recommended to use corrosion inhibitors in combination while focusing on SRB bacteria corrosion in the upper wellbore section, condensate water in the middle section, CO2 content and chloride ion coupling in the lower section, and the size of narrow and shallow corrosion defects causing column safety risks.

Erosion behavior of P110 tubing steel during fracturing operation

Experimental Research on Erosion of P110 Tubing During Perforating

Erosion prediction model for super 13Cr tubing during large-scale hydraulic fracturing

Experimental Study on Erosion of P110 Steel in Liquid-solid Two-phase Flow

Experimental study on erosion wear behavior of PFA coated stainless steel tube

Study on Failure Behavior of Gas Well Tubing Under CO 2 Corrosion After Erosion

Comprehensive analysis of the effect of structural parameters on erosion wear, structural stress, and deformation of high-pressure double-elbow in shale-gas fracturing

Research on the solid particle erosion wear of pipe steel for hydraulic fracturing based on experiments and numerical simulations

Experimental and Numerical Study on the Impact of Sand-Carrying Liquid Erosion on Coiled Tubing Wall

Research on the Erosion Law and Protective Measures of L360N Steel for Surface Pipelines Used in Shale Gas Extraction

Experimental Study on Particle Erosion Failure of Abrupt Pipe Contraction in Hydraulic Fracturing

Numerical Simulation on the Erosion Characteristics of Dense Particles in the Annular Channel of Downhole Fracture Pipe

Simulation of the erosion of casing and perforation under staged sand fracturing conditions in horizontal sections

Research on the Multifactor Synergistic Corrosion of N80 and P110 Steel Tubing in Shale Gas Wells in Sichuan Basin

Experimental Study on CO2 Corrosion of Super 13Cr Integrated Tubing with Erosion Damage

Research on the erosion law of shale gas casing perforation hole during fracturing

Offshore Oilfield Gas Injection Wells Erosion Study and Evaluation

Study of the Erosion-Corrosion Behavior of P110, N80 and VM140 Steel in 3.5wt.%NaCl Solutions with Sand

Study on Erosion Model Optimization and Damage Law of Coiled Tubing

Investigation into the erosion damage mechanism of High-Temperature, High-Pressure, and High-Speed gasflow on metal surfaces

Erosion–corrosion behavior of X65 carbon steel in oilfield formation water