Abstract:Abstract Iron tailings have few macropores which severely inhibit infiltration and transport of soil water. Polyacrylamide (PAM) can regulate soil water, but it is rarely used when remediating tailings matrix. In this research, PAM of four molecular weights of 300w, 600w, 800w, and 1000w were selected as amendments, and were each applied at five mass concentrations of 0% (CK), 0.01%, 0.04%, 0.08%, and 0.16% to observe their effects on water transport in iron tailings using column simulations in the laboratory. After adding PAM, the water retention and saturated water content of iron tailings increased significantly ( P < 0.05). With increases in PAM molecular weight and mass concentration, the saturated hydraulic conductivity showed a downward trend, but the saturated hydraulic conductivity increased after a dry–wet cycle. With the increase of PAM mass concentration, adding PAM of 1000w molecular weight to iron tailing decreased infiltration capacity, but treatments of other molecular weights all initially increased then decreased infiltration capacity. The greatest improvement on infiltration capacity of iron tailings was observed with the addition of PAM of 300w molecular weight and 0.01% mass concentration. Adding PAM increased the vertical depth of the saturation zone of iron tailings ( P < 0.05) with a maximum depth of 20.83 cm. The Kostiakov model more accurately simulated water infiltration of iron tailings compared with the Horton and Philip models. On the whole, when PAM of low molecular weight and concentration was added to iron tailings, PAM increased stable infiltration, saturated water content, and water retention. It also inhibited saturated hydraulic conductivity of iron tailings. Therefore, in practice, it is necessary to select the appropriate molecular weight and mass concentration of PAM according to the dominant limiting factors and remediation needs of the matrix.

Application of Modified Polyacrylamide in Sedimentation of Red Mud

Synthesis, Characterization and Application of Palygorskite/ Polyacrylamide Inorganic-organic Hybrid Flocculent

Effects of a New Synthetic Fe-PAM Flocculants on Filtration and Consolidation of Bentonite Slurry

Synthesis of cationic polyacrylamide via inverse emulsion polymerization method for the application in water treatment

A facile disposal of Bayer red mud based on selective flocculation desliming with organic humics

A Novel Method of Synthesizing Polymeric Aluminum Ferric Sulfate Flocculant and Preparing Red Mud-Based Ceramsite

Sequential usage of charged polyacrylamide for positive feedback in enhancing dewaterability of dredged sediment

Experimental investigation on sedimentation characteristics of coastal slurry by flocculation

Preparation and Application of Polyaluminum Ferric Sulfate from Red Mud: Behaviors of Leaching, Polymerizing, and Coagulation

Studies on Polymeric Soil Structure Amendments III.Amelioration to Lateritic Red Soil by Polyacrylamide

Adsorption of Polyvinyl Alcohol from Wastewater by Sintered Porous Red Mud.

Study on using red mud to control phosphorus release in sediment

High‐efficiency Preparation of Fe–Al Based Flocculants from Red Mud by Microwave Selective Carbothermic Reduction and Magnetic Separation

Preparation of Cationic Polyacrylamide Suspension and Its Application in Oilfield Wastewater Treatment

A novel hydrophobically-modified polyelectrolyte for enhanced dewatering of clay suspension

Sedimentation behavior of flocculant-treated soil slurry

Effects of polyacrylamide molecular weight and mass concentration on water transport characteristics of iron tailings

Multiple Flocculant Prepared with Dealkalized Red Mud and Fly Ash: Properties and Characterization

Revitalizing urban lake cleanup: optimizing flocculation and dewatering of dredged sludge using cation polyacrylamide

Synthesis of hydrophobically modified flocculant by aqueous dispersion polymerization and its application in oily wastewater treatment

Extraction of Aluminum and Preparation of Polymerized Aluminum Ferric Sulfate from Red Mud