Abstract:High-quality precision cropping of hard-to-cut thick wall tubes is urgently needed as the first process for precision forming of tubular parts. Due to the deficiencies of large cutting load and waste of chips and coolants in the present cutting methods, a laser-assisted cyclic chipless splitting (LACCS) method is developed, which prefabricates circumferential crack with large stress concentration by laser, and exerts cyclic rotary load at a low amplitude simultaneously to split the tube. The theoretical laser crack depth and critical loads are derivated for fatigue crack propagation and instant rupture, respectively, and an XFEM model based on cohesive damage criterion is established to reveal the fracture mode based on stress intensity factors. Finally, section quality and microfracture mechanism are investigated by experimental tests with different initial crack depths and load control curves. The results show that critical fatigue splitting load and instant rupture load gradually drop with crack depth at a decreasing rate; for crack depth of 0.7 mm, the critical loads are 0.67% and 34.36%, respectively, of that in the traditional cutting method. The type I crack is the primary fracture mode in this LACCS process, and the stress intensity factor K-1 varies as a cosine curve with peak amplitude of 436.09 MPa(m)(1/2). Step-reduction frequency load can smoothly transite the crack propagation to final rupture, and obtains high quality sections in 16-32 s, with outer roundness error of 0.6%, flatness error of 0.2-0.3 mm and final rupture area of 0.25-1.19 mm(2). The fractographies typically show laser affected zone, cracks propagation zone and final rupture zone. Micro-cracks initiate from the tangency points on the laser notch curve with maximal stress change rate, and the ductile striations propagate with growth rate of 3.3-5.1 mu m/cycle. Final rupture zone forms under shear stress, featured by quasi-parabolic dimples involving microvoid coalescence.

Influences of slotting methods on low-stress precision cutting

Experimental investigation on new low cycle fatigue precision cropping process

An Experimental Investigation of Groove Control for Reducing Drag in a Flat Turbulent Boundary Layer

Effects of Processing Parameters and Tool Geometric Parameters on Residual Stress of Machined 304 Stainless Steel

Influence of the Geometric Parameters of Slotted Bar on Stress Concentration Factor at Prefabricated V-shaped Groove Bottom of the Bar Surface

Investigation on the Crack Initiation of V-Shaped Notch Tip in Precision Cropping

Technology Optimization Analysis of Three-Roll Rotary Piercing Process for Seamless Steel Pipe

Surface feature and material removal in ultrasonic vibration-assisted slot-milling of Ti–6Al–4 V titanium alloy

Experimental Study on New Low Cycle Fatigue Precision Cropping Process

Study on the surface grain state, residual stress and their influence on the deformation of thin-walled parts under ultra-precision cutting

Study on rotary fatigue bend precision blanking of thick-wall metal tube

Effect of Process Parameters on Laser Cutting Quality for Stainless Steel Sheets

Determination of Residual Stress Distribution Combining Slot Milling Method and Finite Element Approach

Laser-assisted Cyclic Chipless Splitting for Hard-to-cut Thick Wall Tubes and Fatigue Fracture Mechanism Analysis

Applications of Integrated Auxiliary Methods Based on Deformation Analysis for Micro-Milling Thin-Walled Slot on Micro-Neck

Study on Residual Stresses in Ultrasonic Torsional Vibration Assisted Micro-Milling

Analysis of machining quality of 304 stainless steel deep hole by changing angle of gun drill

Theoretical study on the effects of the axial and radial runout and tool corner radius on surface roughness in slot micromilling process

Numerical investigation of sequential cuts residual stress considering tool edge radius in machining of AISI 304 stainless steel

Effects of Processing Parameters on Kerf Characteristics and Surface Integrity Following Abrasive Waterjet Slotting of Ti6Al4V/CFRP Stacks

A Comprehensive Experiment-Based Approach to Generate Stress Field and Slip Lines in Cutting Process