Abstract:Micro-alloying effects of Mn and/or Zr on the microstructure evolution of the ageing precipitates of Al-11.5Si–4Cu alloy (in wt.%) were investigated by TEM observation. The relationship of the microstructure evolution with the variation of mechanical properties is discussed. Mn micro-alloying in Al-11.5Si–4Cu alloy decreases the yield strength at room temperature, but significantly increases the yield strength at 300oC in the state after a long-time heat exposure at 300oC for 100h. Zr micro-alloying remarkably improves the yield strength at room temperature and 300oC, but severely degrades the yield strength at 300oC in the state after the same heat exposure. Zr micro-alloying significantly rises the density of the precipitates of θ′ phase formed during the ageing treatment and simultaneously decreases their size, and hence significantly increases the yield strength at room temperature. For Al-11.5Si–4Cu alloy, it is found that the nano precipitates of θ′ which form during the ageing treatment are almost completely transformed into the coarse equilibrium θ phase during the long-time heat exposure. However, Mn micro-alloying greatly suppresses the formation of θ phase or the phase transformation of θ′ → θ during the long-time heat exposure. Thus, the long-time heat exposure only leads to a small decrease of 6Mpa in the yield strength at 300oC of the alloy with Mn micro-alloying. Zr micro-alloying doesn't improve the thermal stability of θ′ phase during the long-time heat exposure, and conversely promotes the phase transformation of θ′→θ. Thus, after the heat exposure at 300oC for 100h, the yield strength at 300oC of the alloys with Zr micro-alloying is greatly decreased, even lower than that of the base alloy.

Study on Thermal Stability of Al-Cu-Mg-Ag-Zr Alloy

Influence of thermal exposure on the microstructure evolution and mechanical behaviors of an Al-Cu-Li alloy

Study on the tensile properties of Al-Zn-Mg alloy based on molecular dynamics

Effect of Thermal Exposure on Microstructure Evolution and Mechanical Properties of TC25G Alloy

Mechanical Properties and Microstructure Evolution of Typical Over-Aging State Al-Zn-Mg-Cu Alloy during Thermal Exposure

The Effect of Thermal Exposure on the Microstructures and Mechanical Properties of 2198 Al–Li Alloy

Enhanced thermal stability and mechanical properties of high-temperature resistant Al−Cu alloy with Zr and Mn micro-alloying

Micro-alloying effects of Mn and Zr on the evolution of ageing precipitates and high temperature strength of Al-11.5Si–4Cu alloy after a long-time heat exposure

High-Temperature Mechanical Behavior of an As-Extruded Al-5Zn-2Mg-0.3Cu (in wt.%) Alloy

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Microstructure Effects on Tensile Brittleness of As-Quenched Zl205A at Elevated Temperature

Effect of Thermal Exposure on the Microstructure and Mechanical Properties of 2A97 Al-Li Alloy

Microstructure and Mechanical Properties at Elevated Temperature of Powder Metallurgy Al-Zn-Mg-Cu Alloy Subjected to Hot Extrusion

Intermediate-Temperature Tensile Behavior of a Hot-Rolled Mg-Li-Al-Cd-Zn Alloy

Effect of heat treatment on microstructure and dimensional stability of ZL114A aluminum alloy

Microstructure and properties of Al-4.8Cu-0.45Mn-0.19Cd-0.18Ti-0.17Zr-0.14V aluminum alloy extrusion bar

Effect of Zr addition on properties of Al–Mg–Si aluminum alloy used for all aluminum alloy conductor

Effect of ageing time on strength and microstructures of an Al–Cu–Li–Zn–Mg–Mn–Zr alloy

Study on Tensile Behavior at Various Temperatures of the Mg-7Gd-5Y-1Nd-2Zn-0.5Zr Alloy

A comparative study on the microstructure and performance stability of Cu-Al2O3 and Cu-Y2O3 alloys after high-temperature annealing

Microstructure and properties of a new Al–Cu–Mg–Zn–Zr–Ti heat resistant aluminum alloy