Abstract:Purpose: Industrial microcomputed tomography (micro-CT) scanners are suitable for nondestructive testing (NDT) of metal, 3D-printed medical components. Typically, these scanners are equipped with high-energy sources that require heavy shielding and costly infrastructure to operate safely, making routine NDT of medical components prohibitively expensive. Alternatively, fixed-current, low-cost x-ray units could be implemented to perform CT-based NDT of 3D-printed medical parts in a subset of cases, if there is sufficient x-ray transmission for the CT reconstruction. A lack of signal-caused by areas of high attenuation in two-dimensional-projection images of metal objects-leads to artifacts that can make an image-based NDT unreliable. We present the implementation of a dual-exposure technique devised to extend the dynamic range (DR) of a commercially available CT scanner equipped with a low-cost low-energy (80 kV) x-ray unit, increasing the signal-to-noise ratio of highly attenuated areas for NDT of 3D-printed medical components. Approach: Our high-dynamic-range CT (HDR-CT) technique adequately combines projection images acquired at two exposure levels by modifying the integration times of each protocol. We evaluate the performance and limitations of this HDR-CT technique by imaging a series of titanium-alloy test-samples. One of the test-samples was a resolution and conspicuity phantom designed to assess the improvements in void visualization of the proposed methodology. The other test-samples were four porous cylinders, 17 × 40 mm , with 60%, 70%, 80%, and 90% nominal internal porosities. Results: Our HDR-CT technique adequately combines projection images acquired at two exposure levels by modifying the integration times of each protocol. Our results demonstrate that the 12-bit native DR of the CT scanner was increased to effective values of between 14 and 16 bits. Conclusions: The HDR-CT reconstructions showed improved contrast-to-noise and void conspicuity, when compared with conventional CT scans. This extension of DR has the potential to improve defect visualization during NDT of medium-size, titanium-alloy, 3D-printed medical components.

Application of Metal Intensifying Screen to the Double-film Technology with Equal Exposure Sensitivity

Metal Thickness Measurement System Based on a Double-Coil Eddy-Current Method with Characteristic Ratio Detection.

Application of Metal Implant 16-Bit Imaging: New Technique in Radiotherapy

Comparisons of Inspection Capability between CR Technology and Film Radiographic

High-dynamic-range micro-CT for nondestructive testing of titanium 3D-printed medical components

A Dynamic Material Discrimination Algorithm for Dual MV Energy X-ray Digital Radiography.

A Calculation on the Metal - Film Mixing by Intense Pulse Ion Beam (IPIB)

High-Quality Cs 3 Cu 2 I 5 @PMMA Scintillator Films Assisted by Multiprocessing for X-ray Imaging

Dual-Material Electron Beam Selective Melting: Hardware Development and Validation Studies

Overlapped Materials Decomposition in High-Energy Dual-Energy X-ray System

Overlapped Objects Discrimination Using Dual-Energy, High Energy X-ray Imaging

An application of differential interference contrast in metallographic examination

PRODUCED THREE-DIMENSIONAL METAL PARTS BY ELECTRON BEAM SELECTIVE MELTING

An H-L Curve Method for Material Discrimination of Dual Energy X-Ray Inspection Systems

Quantitative Detection of Minor Defects in Metal Materials Based on Variation Coefficient of CT Image

Organic and Inorganic Metal Halide Tandem Scintillator for Dual-Energy Flat-Panel X-ray Imaging

Unconventional High-Value Utilization of Metallurgical Iron-Bearing Dust as Shielding Composite for Medical X-rays

Monoenergetic Imaging of Dual Energy CT in the Evaluation of Metal Fixation of Factures

A Defect Detection Method for the Surface of Metal Materials Based on an Adaptive Ultrasound Pulse Excitation Device and Infrared Thermal Imaging Technology

Metal Artefact Reduction for Orthopaedic Devices Using Monoenergetic Extrapolation from Dual-energy Computed Tomography

Projection-domain Metal Artifact Correction Using a Dual Layer Detector