EVALUATION OF COMPOSITE MATERIALS BY ULTRASONIC C-SCAN IN DEPTHS

Song-ping LIU,En-ming GUO,Qian-lin ZHANG,M Vadim,Lu-gen ZHANG,Wen-zeng YAO

DOI: https://doi.org/10.3969/j.issn.1000-6656.2001.01.005

2001-01-01

Abstract:An evaluation technique, based on ultrasonic characteristics in time domain, by which several Cscan images in depths of a material tested can be obtained by once-through scanning, has been presented.

What problem does this paper attempt to address?

Research on Ultrasonic C-scan Technique for Large Unsymmetric Composite Component

王艳颖,吴瑞明,周晓军,程耀东

DOI: https://doi.org/10.3785/j.issn.1008-973x.2004.09.023

2004-01-01

Abstract:In the ultrasonic C-scan of unsymmetric composite component, the probe is difficult to aim at the normal component direction and the ultrasonic attenuation is severe. To solve these problems, profile measurement and restructured modeling were used to track the surface of the component and realize the (realtime) sensitivity compensate. The initial curved surface model of skin was established using the preliminary ultrasonic data. Then, the point station for controlling probes move was calculated. The surface model of the component was reconstructed by the method of profile measurement and reverse engineering. The sensitivity compensate was realized through calculating the thickness of component at measuring point. Path of C-scan was programmed based on the restructured model and the principle of the smallest ultrasonic attenuation. Finally, the C-scan images of the unsymmetric composite component were received. It is shown that the precision and efficiency of ultrasonic detection can be increased by taking practical measures in the site.
Study on Multisensor Information Fusion in Ultrasonic C-Scan System of Composite Material

WU Rui-ming,ZHOU Xiao-jun,WANG Bang-kai

DOI: https://doi.org/10.3969/j.issn.1004-1699.2005.03.030

2005-01-01

Abstract:According to do the task of multisensor information fusion in ultrasonic C-Scan system,defect classification and defect recognition of composite material were discussed.Profile measurement and restructured modeling were used to solve ultrasonic C-Scan of composite material.By information fusion of fuzzy integral,fusing multisensor non-vision,human's perceiving information and vision information were realized.Experiment results validated that uncertainties of system were reduced and performances of ultrasonic testing and recognition system were improved through technique of multisensor information fusion.
Study on Ultrasonic C-Scan Technique for Variation Thickness Aviation Forged Piece

Si-yuan WU,Xiao-jun ZHOU,Xiong-bing LI,Hui-feng ZHENG

DOI: https://doi.org/10.3969/j.issn.1004-1699.2006.04.032

2006-01-01

Abstract:In the ultrasonic C-scan of variation thickness aviation forged piece using pulse echo method, the flaw recognition region between interface echo and bottom echo changes along with the part’s thickness at different scan point, this leads to the range of the flaw recognition region hard to determine without knowing the part’s thickness, and makes difficulties to automatic recognise the flaw. Aiming at this problem, uses the method of obtaining the part’ thickness to help the inspection software determine the flaw recognition region. First, measures the part’s surface using ultrasonic non-contact measurement method; then, with the measurement data of the surfaces, calculates the part’s coarse thickness at each scan point using Z-map method; finally, with the help of the part’s thickness, the inspection software automatic tracks the bottom echo and determine the range of flaw recognition region. It is shown that this method can nicely meet the demand of ultrasonic C-scan for variation thickness aviation forged piece.
Comparative Study of Ultrasonic Techniques for Reconstructing the Multilayer Structure of Composites

Xiaoyu Yang,Erik Verboven,Bing-feng Ju,Mathias Kersemans

DOI: https://doi.org/10.1016/j.ndteint.2021.102460

IF: 4.683

2021-01-01

NDT & E International

Abstract:The multilayer structure of fiber-reinforced polymers may be extracted by ultrasonic pulse-echo inspection. Depending on the employed ultrasonic frequency and subsequent processing methodology, different depth resolution and dynamic depth range can be achieved. This study compares the performance of different ultrasonic pulse-echo approaches for extracting the ply-by-ply structure of multilayered composites. The following methodologies are studied: Method 1: 50 MHz, 15 MHz, and 5 MHz ultrasound with low-pass filtering using analysis of the instantaneous amplitude, Method 2: 15 MHz ultrasound with Wiener deconvolution (and autoregressive spectral extrapolation) using analysis of the instantaneous amplitude, and Method 3: 5 MHz ultrasound with lowpass or log-Gabor filtering using analysis of the instantaneous phase. In the simulation study, the performance of the various techniques is investigated on synthetic data representative for a 24-ply carbon fiber reinforced polymer. The robustness of the techniques is evaluated for different signal-to-noise ratios. The various techniques are further investigated on experimental data of a 24-ply cross-ply carbon fiber reinforced polymer. The ply-byply structure is extracted and presented in the form of both B-scan and C-scan images. The thickness of each ply is estimated for quantitative analysis. The obtained results indicate that the 5 MHz ultrasound coupled to analyticsignal analysis with log-Gabor filter shows the best performance for reconstructing the multilayer structure of the studied composites.
Simultaneous Measurement of Local Longitudinal and Transverse Wave Velocities, Attenuation, Density, and Thickness of Films by Using Point-Focus Ultrasonic Spectroscopy

Bing-Feng Ju,Xiaolong Bai,Jian Chen

DOI: https://doi.org/10.1063/1.4758136

IF: 2.877

2012-01-01

Journal of Applied Physics

Abstract:This paper presented an ultrasonic technique for simultaneous determination of the complete set of acoustical and geometrical properties of a layer embedded between two known materials using point-focus ultrasonic spectroscopy, which provides a high lateral resolution. The theoretical model of the two-dimensional spectrum Rt (θ, ω) of the layer is calculated as a function of six parameters of longitudinal and transverse velocities cl, ct, attenuation αl, αt, density ρ and thickness h, which fully determined the layer properties. The experimental spectrum Re (θ, ω) can be measured by V(z, t) technique. A two-step algorithm is presented to decompose the searching process of parameters from one six-dimensional to two three dimensional spaces. The sensitivity of the two-dimensional spectrum to individual properties and its stability against experimental noise are studied. The full set properties of a 250 μm thick stainless steel plate immersed in water are determined. The proposed technique used a point focus transducer, which makes the set-up simple and reliable. It allows measurement of the local properties of the layer and enables precision material characterization.
Manual Scan Ultrasonic Feature Imaging Testing of Composite Material

张锐,陈以方,付德永

DOI: https://doi.org/10.3969/j.issn.1001-4381.2003.04.011

2003-01-01

Journal of Materials Engineering

Abstract:The manual featuredscan ultrasonic imaging system for composite materials is developed The establishment of fullwave acquisition of ultrasonic testing signal makes the system a fullinformation processing ability of the waveform features for any testing point Moreover, various testing methods of featurescan imaging are established: Ascan and parameter measurement, B scanning, Cscan imaging, phase feature imaging, equivalent feature imaging, halfwavelength ultrasonic chromatography and ultrasonic spectrum analysis A testing experiment of a carbon fiber composite specimen has been done and the result displays the interior quality status of the specimen accurately
Testing of Thin Laminated Composite Plate with Ultrasonic Feature Scan Imaging System

LU Ming-hui,FU De-yong,WANG Hai-fang,LI Qing,WANG Shu-shuang,CHEN Yi-fang

DOI: https://doi.org/10.3969/j.issn.1000-6656.2005.09.001

2005-01-01

Abstract:Conventional ultrasonic imaging methods such as B-scan and C-scan couldn't meet the requirements of composite inspection. A new ultrasonic imaging method, feature scan (F-scan) imaging, was introduced including its inspecting principle, scanning system design and focusing transducer manufacture and so on. In the method of F-scan imaging, ultrasonic waveform features (i.e. rising and falling time, pulse period and frequency spectrum) and defect features (i.e. the type, shape and size of defects) were taken as characteristic quantity to acquire and reconstruct the signals received, and finally to make imaging. The laminated composite thin plate with thickness of 2 mm was taken as testing sample, in which three lamination defects with diameter not less than  1.2 mm were made on the binding layers at 0.6 mm and 1.4 mm from the upper surface of the composite plate respectively. It was shown by experimental results that the prepared defects were successfully detected by the ultrasonic feature scanning system designed with various imaging modes (e.g. amplitude imaging, depth imaging and bottom wave imaging). The designed system had an additional function of computed tomography, and could also be used for the imaging of both the density of thin laminated plate and the thickness of hard alloys. Based on its special and effective function, ultrasonic feature scan imaging method would find wide application in material analysis.
Simultaneous Measurement of Elastic Moduli, Attenuation, Density, and Thickness of a Layer by Ultrasonic Spectroscopy Using Point-Focus Transducer

Xiaolong Bai,Jian Chen,Bing-feng Ju,Keji Yang

DOI: https://doi.org/10.1109/ultsym.2012.0181

2012-01-01

Abstract:This paper presents an ultrasonic technique for simultaneous determination of the complete set of acoustical and geometrical properties of a layer embedded between two known materials using point-focus transducer, which provides a high lateral resolution. The theoretical model of the two-dimensional spectrum Rt(θ,ω) of the layer is calculated as a function of six parameters: longitudinal and transverse velocities ci, ct, attenuation αi, αt, density ρ and thickness h, which fully determined the layer properties. The experimental spectrum Re(θ,ω) can be measured by V(z,t) technique using point-focus transducer which is verified in our previous work. By minimizing the differences between the theoretical and experimental spectra at normal and oblique incidence, the six parameters of the layer can be derived. The full set of the properties of a 250μm thick stainless steel layer immersed in water are determined using this technique as an example. This measurement technique enables precise measuring of the local full set properties of layers.
Application of Ultrasonic Squirter Transmission Method in Detection of Advanced Composite Materials

Zhao Jianhua,Luo Ming,Wu Shihong,He Shuangqi,Zhao Weidong

DOI: https://doi.org/10.3969/j.issn.1007-2330.2012.04.028

2012-01-01

Abstract:The basic theory of ultrasonic squirter transmission method and the four-axes automatic ultrasonic squirter transmission C-scan system were introduced.Several advanced composite materials including the flat plate sample,the heavy section forming and the cylinder structure were studied by the system and method.The results show that the defects such as pore,crack,sticky point and lamination in the advanced composite materials can be effectively detected by this method.
Simultaneous Thickness, Velocity, Density, and Attenuation Measurement of a Thin Layer by Time-Resolved Acoustic Microscopy

Jian Chen,Xiaolong Bai,Keji Yang,Bingfeng Ju,Jianxing Meng

DOI: https://doi.org/10.1121/1.4755238

2012-01-01

The Journal of the Acoustical Society of America

Abstract:An ultrasonic method for simultaneous determination of thickness, velocity, density and attenuation of thin layer using a time-resolved acoustic microscopy is proposed. Reflection from the thin layer is represented as a function of three dimensionless parameters which are determined from the experimentally normal incidence component of the two dimensional reflection spectrum R(θ,ω) derived based on the inversion of V(z,t) technique with time-resolved acoustic microscopy. The thickness of the thin layer is derived from the signals received from the layer itself considering the geometrical relations when the lens focused on the sample’s surfaces. The simultaneous determination of thickness, velocity, density and attenuation of thin stainless steel plate by using a point-focusing transducer with nominal frequency of around 50MHz were carried out. The determined material properties are comparable, in which the thickness, velocity and density can be measured with a percentage biases less than 5% and the attenuation is close to its real value. The present preliminary work shows the high efficiency, viability and capability of the new non-destructive technique in simultaneously characterize basic mechanical and geometrical properties of thin layers.
Visualized characterization of diversified defects in thick aerospace composites using ultrasonic B-scan

Zhen Zhang,Menglong Liu,Qian Li,Yifeng Ang

DOI: https://doi.org/10.1016/j.coco.2020.100435

IF: 8

2020-12-01

Composites Communications

Abstract:<p>Multiple defects including fiber waviness, resin rich layers, porosity and delamination may initiate in aerospace composite structures during manufacturing and service, and thus potentially cause structural failure. In this paper, ultrasound testing for aerospace composites with complex microstructures was investigated through both simulation and experiment. Ultrasonic testing challenges of aerospace composites were concluded as frequency-dependent inter-ply reflection, interfering reflection from multiple defects, and frequency-dependent wave distortion caused by fiber waviness. Ultrasonic B-scan imaging with both amplitude and phase information at different frequencies are proposed to achieve defect differentiation and characterization for the thick composites with fiber waviness. This research will facilitate the understanding of defect presence in the B-scan images under different frequencies and indicate the direction for improving ultrasonic testing of aerospace composites.</p>

materials science, composites
Survey of Materials Testing Using Ultrasonic

Fei Zhong,Wei Zhang,Biaoqiang Jiao,Yuexian Zhong

DOI: https://doi.org/10.4028/www.scientific.net/amr.146-147.412

2010-01-01

Advanced Materials Research

Abstract:In this paper, ultrasonic materials testing researches are reviewed. The latest progress of ultrasonic testing technology is introduced, including water-squirting ultrasonic C-scan testing, laser ultrasound, ultrasonic feature scan imaging, signal processing and pattern recognition technology in the application of ultrasonic testing.
Method of Imaging and Evaluation for Defect Based on Pulsed Eddy Current

Zhao Shuhao,Luo Xuwei,Huang Pingjie,Peng Xiedan,Hou Dibo,Zhang Guangxin

DOI: https://doi.org/10.1109/i2mtc.2016.7520427

2016-01-01

Abstract:As a non-destructive testing method, pulsed eddy current has certain advantages in hidden defect detection problems. A C-Scan imaging method based on LabVIEW is proposed in this paper and defect evaluation is carried out. In defect evaluation, a profile detection algorithm based on Canny operator is applied. The characterization of depth and shape of defects is studied. Experimental results show that defects can be detected and displayed by using the imaging and evaluation method presented in the paper. In contrast to the normal threshold method, the algorithm based on Canny operator can extract the profile of defects more accurately which will be an advantage for hidden defect inspection.
Determination of the Multiple Local Properties of Thin Layer with High Lateral Resolution by Scanning Acoustic Microscopy.

Xiaolong Bai,Zeqing Sun,Anyu Sun,Jian Chen,Bing-Feng Ju

DOI: https://doi.org/10.1063/1.4894261

2014-01-01

Abstract:Simultaneous determination of the multiple local acoustic and geometrical properties of the thin layer with a high lateral resolution is of great interest in ultrasonic non-destructive evaluation. In this paper, we propose a technique based on the V(z, t) data to simultaneously determine the four local properties of the thin layer, namely, the thickness, the sound velocity, the acoustic impedance, and the density. First, the V(z, t) data are collected from both the thin layer and the reference material. Then the sound velocity and the thickness are calculated by focusing the point-focusing transducer on the front and back surfaces of the thin layer, with the confocal positions determined by averaging the peak positions in the V(z) curves at different frequencies. Second, the acoustic impedance of the thin layer is obtained based on the experimental and theoretical two-dimensional reflection spectrum using the echo from the front surface of the layer. Finally, the density can be obtained by dividing the acoustic impedance by the sound velocity. The four local properties of an aluminum layer are accurately obtained using our method. The largest relative error of determining the four properties is around 1%. This technique opens a new way of simultaneously measuring the multiple local acoustic and geometrical properties of thin layers.
Wavenumber-Domain Fast Reconstruction Technique Using Ultrasonic Scanning for Transverse Wave Imaging

Chen Mu,Jin Haoran,Yang Keji,Ju Bingfeng

DOI: https://doi.org/10.3788/lop223109

2023-01-01

Laser & Optoelectronics Progress

Abstract:Ultrasonic nondestructive testing is of great significance to ensure the working of equipment in aerospace, petrochemical, railway, and other fields. Transverse wave ultrasonic testing is an important method for the detection of internal defects in solids due to its advantages of weak attenuation of vibration mode, low sound speed, and high spatial resolution. However, due to the vibration characteristics of piezoelectric wafers, conventional ultrasonic transducers cannot directly transmit and receive transverse waves and need to refract the transverse waves with the help of oblique incidence, and due to the particularity of oblique incidence, it is necessary to consider the refraction effect and slope detection simultaneously, which increases the burden of ultrasonic imaging reconstruction calculation. Therefore, a wavenumber-domain fast reconstruction technique using ultrasonic scanning for transverse waves is proposed. The method is built based on classical synthetic aperture focusing technology (SAFT) by integrating the coordinate transformation in wavenumber domain and transverse wave wavefield extrapolation for the application of oblique incidence transverse wave imaging. The simulation and experimental results show that the proposed method can build excellent detection results when detecting transverse holes, cracks, and hemispherical flat-bottom holes with refraction angles from 20 degrees to 60 degrees. Compared with the time-domain synthetic aperture focusing technique, the computational efficiency of this method is improved by at least 100 times without losing the reconstruction accuracy.
Comparative Study on Ultrasonic C-Scan Imaging of Composite Lap Joints Using Piezoelectric Transducer: Pulse-Echo and Pitch-Catch Configurations

Mohsen Barzegar,Dario J. Pasadas,Artur L. Ribeiro,Helena G. Ramos

DOI: https://doi.org/10.1109/tim.2024.3368490

IF: 5.6

2024-03-02

IEEE Transactions on Instrumentation and Measurement

Abstract:This article compares low-frequency (LF) Lamb waves in a pitch-catch configuration and high-frequency (HF) bulk waves in a pulse-echo mode for ultrasonic C-scan imaging of composite lap joints. The pulse-echo measurement is conducted by using a delay line transducer. On the other hand, the ultrasonic guided waves are measured in a pitch-catch configuration by using a PZT disk moved by a positioning system over the scan area. In both methods, the signals are acquired in a C-scan manner over the adhesive joint area. Applying signal processing techniques, including frequency-wavenumber filtering and bandpass filtering, along with different feature extraction, the images of the scan area are obtained. For this study, two different types of composite lap joints are used. The first joint consists of composite plates reinforced with woven composite fabric, with defects in the form of missing adhesive. In the second joint, quasi-isotropic composite plates are employed, and disbonds are used to simulate defects. The Fisher discriminant criterion is used to assess the capability of each method in accurately distinguishing defects from the pristine condition. This article concludes with a discussion of the results and effects of using both techniques.

engineering, electrical & electronic,instruments & instrumentation
DESIGN AND STUDY OF ULTRASONIC TEST SYSTEM FOR VOID CONTENT IN COMPOSITE MATERIALS

JIANG Zhi-feng,WU Rui-ming,WU Zuo-lun,SONG Li-jun

DOI: https://doi.org/10.3969/j.issn.1003-0999.2009.04.008

2009-01-01

Abstract:On the basis of ultrasonic test theory model,the ultrasonic testing data acquisition and data processing methods were described.Computer control system for ultrasonic testing technology researched time-domain waveform signal processing based on ultrasonic board.The C-scan image and column chart of CFRP surface were obtained.The result showed that the test system based on automation can accurately test the void content of carbon fiber reinforced plastics on the spot.
Ultrasonic Signal Character and Quality Evaluation of Cu/steel Surfacing Weld

GAO Shuangsheng,GANG Tie,GUI Guangzheng,YUAN Yuan

DOI: https://doi.org/10.3321/j.issn:0253-360x.2007.05.026

2007-01-01

Abstract:By using water immersion focusing method in an ultrasonic C-scan inspection system,the quality of Cu/steel surfacing weld was evaluated.The sound field in the two planes of axial and radial to the cylinder were analyzed when the sound beam vertically incidents into the cylindrical work piece.Based on the above theoretical analyses,surfacing welds were inspected by C-scan mode.In order to verify the reliability of ultrasonic test,ultrasonic A-scan signals received from typical area of the workpiece were studied and the corresponding destructive test was done.The result shows that it is feasible to evaluate the surfacing weld by using the proposed method.Moreover,the tested result is more reliable when sound beam incidents into the piece from the base metal.
The Ultrasonic Feature Imaging Testing of special structure

Minghui LU,Yi ZHU,Xin LIU,Xun-feng LIU,Yifang CHEN

2008-01-01

Abstract:The broadband narrow pulse self-focusing ultrasonic transducer was designed for the special structure of the column holes, and used to do the r esearch for the testing of bonding layer of metal composite material with F-scan ultras onic imaging system. The copper-steel boding layer of bimetal rotor is connected by diffusing wel ding. There may be delamination flaws existed here. The depth and range feature image can be displayed through the full wave trains time-frequency transform of the ultrasonic signal . Then the people could find out the delamination flaws of bonding layer and estimate their s ize by analyzing and evaluating the information of the images.
Baseline-free Defect Evaluation of Complex-Microstructure Composites Using Frequency-Dependent Ultrasound Reflections

Zhen Zhang,Menglong Liu,Qian Li,Melody Png

DOI: https://doi.org/10.1016/j.compositesa.2020.106090

2020-01-01

Abstract:In this study, baseline-free defect characterization for both flat and ply-drop composites were proposed using frequency dependence of ultrasound reflections. This frequency dependence of ultrasound interaction with delamination and resin layers in composites were investigated through CIVA® simulation and experimental investigation. To extract quantitative data of frequency dependence of ultrasonic reflections in composites with a single test, synchrosqueezed wavelet transform was adopted to decompose the acquired wide-band raw signals into narrow-band frequencies. Quantitative analysis concluded that dependence of ultrasound reflections from defects on frequency in composites are affected by wavelength-to-defect ratio, polymer viscoelasticity, frequency-dependent inter-ply reflections and waviness-induced scattering. Considering these factors, our study found that volumetric defect reflections have a unique frequency dependence. This allows volumetric defect identification and characterization in ultrasonic B-scans to be achieved without comparison to a baseline reference. The proposed method shows a promising solution for non-destructive evaluation of multi-layer composites with diverse microstructures.

EVALUATION OF COMPOSITE MATERIALS BY ULTRASONIC C-SCAN IN DEPTHS

Research on Ultrasonic C-scan Technique for Large Unsymmetric Composite Component

Study on Multisensor Information Fusion in Ultrasonic C-Scan System of Composite Material

Study on Ultrasonic C-Scan Technique for Variation Thickness Aviation Forged Piece

Comparative Study of Ultrasonic Techniques for Reconstructing the Multilayer Structure of Composites

Simultaneous Measurement of Local Longitudinal and Transverse Wave Velocities, Attenuation, Density, and Thickness of Films by Using Point-Focus Ultrasonic Spectroscopy

Manual Scan Ultrasonic Feature Imaging Testing of Composite Material

Testing of Thin Laminated Composite Plate with Ultrasonic Feature Scan Imaging System

Simultaneous Measurement of Elastic Moduli, Attenuation, Density, and Thickness of a Layer by Ultrasonic Spectroscopy Using Point-Focus Transducer

Application of Ultrasonic Squirter Transmission Method in Detection of Advanced Composite Materials

Simultaneous Thickness, Velocity, Density, and Attenuation Measurement of a Thin Layer by Time-Resolved Acoustic Microscopy

Visualized characterization of diversified defects in thick aerospace composites using ultrasonic B-scan

Survey of Materials Testing Using Ultrasonic

Method of Imaging and Evaluation for Defect Based on Pulsed Eddy Current

Determination of the Multiple Local Properties of Thin Layer with High Lateral Resolution by Scanning Acoustic Microscopy.

Wavenumber-Domain Fast Reconstruction Technique Using Ultrasonic Scanning for Transverse Wave Imaging

Comparative Study on Ultrasonic C-Scan Imaging of Composite Lap Joints Using Piezoelectric Transducer: Pulse-Echo and Pitch-Catch Configurations

DESIGN AND STUDY OF ULTRASONIC TEST SYSTEM FOR VOID CONTENT IN COMPOSITE MATERIALS

Ultrasonic Signal Character and Quality Evaluation of Cu/steel Surfacing Weld

The Ultrasonic Feature Imaging Testing of special structure

Baseline-free Defect Evaluation of Complex-Microstructure Composites Using Frequency-Dependent Ultrasound Reflections