Abstract:The microstructure of single crystal Ni-based superalloys is virtually determined by both processing parameters of growth rate v and thermal gradient G ahead of the solidification front. Previous researches have established the relationship between dendrite spacings and G or v under supposing those parameters to be constant from beginning to end of solidification, resulting in the disaccord between the predicted and experimental results for actual blade, productions. Furthermore, previous experimental and theoretical works seldom involve the influence of processing parameter change on dendrite growth for multi-component industrial alloys. Therefore, investigation of directional solidified microstructure varying with processing parameter is the focus of present study. The influence of the withdrawing rate transition during directional solidification on the primary dendrite arm spacing (PDAS) and microsegregation for single crystal superalloy DD3 has been studied by liquid metal cooled (LMC) directional solidification method. A wide range of withdrawing rate variations from 50 to 600 mu m/s is allowable under G high to 250 K/cm. The results indicate that the average PDAS is remarkably dependent on the history of growth rate variation. The smaller PDASs of 56.5 and 86 mu m can be obtained under withdrawing rate transition from higher values of 600 and 300 mu m/s into 100 mu m/s, while they are kept being 111.5 mu m if withdrawing rate is 100 mu m/s all the time. In contrast. PDASs increase to 109 and 93 mu m under withdrawing rate transition from lower values of 50 and 100 mu m/s into 300 mu m/s, while they are kept being a small value of 70 mu m if growth rate is 300 mu m/s at beginning. These experimental results agree approximately with those from Hunt-Lu model, but the maximum to minimum ratio of PDASs at a given solidification parameter, i.e., lambda(max)(1)/lambda(min)(1), is proved to be more than 2. It is also shown that the dendrite microsegregation will be lessened with the decrease of PDASs at the same current solidification parameters.

Effect of Variation in Cross-Section Size of Samples on Directional Solidification Microstructure of DZ125 Superalloy

Effect of Directional Solidification Methods on Solid Solution Window in Ni-based Single-Crystal Superalloy

Microstructural Evolution of Directionally Solidified DZ125 Superalloy Castings with Different Solidification Methods

Effects of Forced Melt Flow on Microstructure Evolution of DZ125 Superalloy During Directional Solidification

Microstructural Evolution of Directionally Solidified Ni-Based Superalloy Dz125 under High Temperature Gradient

Microstructure Evolution of Directionally Solidified Dz125 Superalloy with Melt Superheating Treatment

MICROSTRUCTURAL EVOLUTION OF DIRECTIONALLY SOLIDIFIED Ni--BASED SUPERALLOY DZ125 UNDER PLANAR GROWTH

Effect of Directional Solidification Methods on the Cast Microstructure and Grain Orientation of Blade Shaped Dz125 Superalloy

CA SIMULATION OF MICROSTRUCTURE OF DIRECTIONALLY SOLIDIFIED DZ125 SUPERALLOY

Effect of Sample Size on Intermetallic Al2Cu Microstructure and Orientation Evolution During Directional Solidification

Interfacial morphology evolution in directionally solidified Al-1.5%Cu alloy

Effects of specimen dimensions on directional solidification microstructure and interface stability of Al-4.5%Cu alloy

INFLUENCE OF WITHDRAWING RATE TRANSITION ON THE PRIMARY DENDRITE ARM SPACING AND MICROSEGREGATION OF DIRECTIONALLY SOLIDIFIED SINGLE CRYSTAL SUPERALLOY DD3

Influence of Directional Solidification Variables on Primary Dendrite Arm Spacing of Ni-based Superalloy DZ125

Effect of Solidification Rate on Grain Structure Evolution During Directional Solidification of a Ni-based Superalloy

Characterization of Microstructures and Growth Orientation Deviating of Al2Cu Phase Dendrite at Different Directional Solidification Rates

Dependence of microstructure and mechanical properties on solidification condition of directionally solidified Zn-55Al-1.6Si alloys

Microstructure Evolution of Directionally Solidified Al-Cu Alloys

Microstructure Evolution and Competitive Growth During Grain Growth of Directionally Solidified Column Crystal DZ4125 Superalloy

Influence of withdrawal rate on microstructures of blade shaped directionally solidified DZ125 superalloy

Solidification Microstructure of Directionally Solidified Superalloy under High Temperature Gradient