Abstract:Many mathematical models describing the thermo-mechanical behaviors of strand and mould have been documented and used in recent years to make a further understand on the deformation behaviors of the solidifying shell and mould distortion. In the earlier stage, many two-dimensional thermo-mechanical mathematical models, either in transverse section or in axial planes, had been developed to predict the stress generation. And Thomas et al. developed a two-dimensional slice stress model at the height corresponding to the highest mould temperature from a three-dimensional heat transfer model for slab casting. And even three-dimensional thermo-mechanical models have also been developed, at the expense of greater computation time and memory. In the casting process, the heat transfer from the billet to mould and the deformation of mould interact each other. So, many models were developed for the coupled analysis of them of both billets and slabs. Kelly developed a model coupling the mould heat transfer and mould deformation by direct computation of the gap thickness, and by cycling between the thermal and stress analysis to derive a self-consistent solution for the temperature distributions in and of mould, along with the air gap size. To make the results better reflect the real casting conditions, the stress states of strand and mould was predicted based on the calculation temperature as thermal load by inverse model from thermocouples reading along the centerline for slab and billet casting. During the continuous casting mould process the solidifying shell is subjected to various stresses, including thermal stress, stress due to ferrostatic pressure, and stress caused by friction (liquid lubrication and solid–solid contact friction), and even their combined stress. Ferrostatic pressure in the calculation of strand stress had been considered by most of the thermo-mechanical models mentioned above. The mould can interact mechanically with the shell if contact occurs, and so contact and friction against the mould is the source of many of the critical stresses in a casting, and one 2D model investigated the effect of contact friction between solidifying shell surface and mould wall based on the Coulomb friction law. The real continuous casting mould process in plant is still not fully understood. In the present work, an attempt is made to improve this situation by developing an appropriate three-dimensional, thermo-elasto-plastic finite element stress model taken the temperature of strand and mould as thermal loaded, calculated by the 3D inverse problem model from the measured temperatures by the thermocouples buried in various locations, in so doing, a fresh insight has been gained into the thermal-mechanical states of strand and mould. Furthermore, the influence of mould friction on strand stress is also discussed.

FEM Modelling of the Temperature Field and Stress Field of Mould Wall in High Speed Casting of Steel Billet

FEM Analysis of Temperature and Stress Fields of Mould Wall in Continuous Casting of Steel Billet

FE Numerical Simulation of Mould Temperature Field During the Continuous Casting of Steel

3D Stress Model with Friction in and of Mould for Round Billet Continuous Casting

Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

Simulation of Temperature Field and Prediction of Shell Thickness in a Continuous Casting Mould of Round Billets

ISIJ International, Vol. 46 (2006), No. 4, pp. 546–552

Non-uniformity of Mould Heat Transfer and Distortion During Wide and Thick Slab Continuous Casting

Coupling Numerical Simulation of Flow Field, Temperature Field and Stress Field in a Wide-Thick Slab Continuous Casting Mold

Thickness Distributions of Mold Flux Film and Air Gap in Billet Ultra-High Speed Continuous Casting Mold Through Multiphysics Modeling

3-D Inverse Problem Continuous Model for Thermal Behavior of Mould Process Based on the Temperature Measurements in Plant Trial

Real-time Analysis on Non-uniform Heat Transfer and Solidification in Mould of Continuous Casting Round Billets

Analysis of heat transfer and thermal stress in continuous casting with mechanical reduction

Thermo-mechanical Modeling in Continuous Slab Casting Mould and Its Application

Finite element numerical simulation on Thermo Mechanical couple in bloom mold

Thermomechanical Model of Heat Transffer in Bloom Casting Mold

Finite Element Method of 3D Stable Heat Conduction of Steel Fluid in Continuous Casting Moulds

FINITE ELEMENT ANALYSIS OF THERMO-MECHANICAL COUPLED SOLIDIFICATION PROCESS OF CONTINUOUS CASTING SLAB IN MOLD

Analysis of Non-uniform Mechanical Behavior for a Continuous Casting Mold Based on Heat Flux from Inverse Problem

Thermal Behaviour Of Moulds With Different Water Channels And Their Influence On Quality In Continuous Casting Of Beam Blanks

Numerical Analysis of Solidified Shells in Moulds for Continuous Casting of Thin Slabs