Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

Microstructure and Mechanical Properties of Welded Joints of 440 MPa Grade Marine Engineering Steel under Different Welding Methods

Microstructure and Mechanical Properties of the Arc Welded Joint of 400mpa Grade Ultrafine Grained Steel

Microstructure and Mechanical Properties of an Underwater Wet Welded Dissimilar Ferritic/Austenitic Steel Joint

Study on Microstructure and Properties of Welding Joints for 400 MPa Ultrafine Grained Steel by Different Welding

Microstructure and Properties of Fiber Laser Wire Welded Joints of 1OCrSiNiCu High Strength Shipbuilding Steel

Microstructure and mechanical properties of dissimilar steel welded joint of martensite stainless steel and low alloy steel

A comparative study of the microstructure and properties of 800 MPa microalloyed C-Mn steel welded joints by laser and gas metal arc welding

Microstructure and mechanical properties of weld metal in laser and gas metal arc hybrid welding of 440-MPa-grade high-strength steel

Microstructure and Properties of Welding Joints for 400MPa Ultrafine Grained Steel by Deferent Carbon Dioxide Arc Welding Processing

Study on Microstructure and Mechanical Properties of Flash Butt Welded Joint of NS700 Acid-resistant Steel

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

Insights into microstructure evolution and fracture mechanisms of welded joints of high strength steel patchwork components

Studies of Mechenical Properties and Microstructures of Argon-Shielded Arc Welding Joint of GH536 Superalloy

Microstructure and Mechanical Properties of Underwater Wet Welded High Carbon-Equivalent Steel Q460 Using Austenitic Consumables

Microstructure and mechanical properties of stainless steel clad plate welding joints by different welding processes

Microstructure and Toughness of Laser Welded Joint of 400mpa Ultra-Fine Grained Steel

Microstructure and Performance of Hybrid Laser-Arc Welded 40 Mm Thick 316 L Steel Plates

Microstructure and mechanical properties of stainless steel clad plate joints produced by TIG and MAG hybrid welding

Microstructure and Mechanical Properties of MIG Welds between 6252 Armor Steel and Q550D HSLA Steel

Microstructures and Properties of 50 mm Thick SA508Gr.3Cl.2 Steel Welding Joints by Ultra-Narrow-Gap Laser Welding with Filler Wire