Abstract:The effects of the area reductions on the crystal orientation, eccentricity, and mechanical properties of GH4145 alloy tubes prepared by three-roller cold rolling were studied. Electron backscattered diffraction analysis showed that the equiaxed grains of the annealed tube blank gradually changed into elongated crystals along the axial direction (AD) with increased deformation. In addition, the grain orientations rotated from random distribution towards the <101>//radial direction (RD), <111>//AD, and <101> + <111>//tangential direction (TD). Brass, copper, S, and {123}< 111‾ > textures formed and increased in strength with increasing strain. Room-temperature tensile tests loaded along the AD and TD demonstrated yielding anisotropy of the tubes. With increasing strain, the work hardening increased continuously, and the dislocations slipped in three directions and then transformed into slip bands and dislocation cells, whereas a few deformation twins formed as the reduction reached 64%, and then slipped in two directions. When the reduction was 64%, the activated slip system transformed from {111}<110> to {110}<001> in most grains under applied AD loading, which was consistent with the loading in both directions at a reduction of 72%. As the grains in the preferential deformation zone near the inner and outer walls rotated to the <101>//RD orientation, the tubes plastically deformed, and the grains in the central layer then gradually begin to rotate. The ratio of radial length in the deformation hysteresis zone to wall thickness was used to represent the degree of non-uniformity of the deformation. A direct correlation was found between the eccentricity of the wall thickness and the non-uniformity of tube deformation as the area reduction increased from 13% to 50%. In addition, the radial delamination of the tubes disappeared, deformation became uniform, and the eccentricity decreased significantly as the area reduction increase up to 64%. Therefore, the dimensional accuracy and uniformity of the tubes can be further improved by controlling the strain of the tube.

Influence of Extrusion Needle Withdrawal Speed on Orange Peel Wrinkle Defects on Inner Surface of Stainless Steel Tube

Quantitative analysis of orange peel during tension of 6063 alloy spun tubes

Influence of billet fillet on outside surface of extrusion stainless tube

Effect of Strain State on the Surface Roughening for Hydroforming of Aluminum Alloy Tube Based on Cross-Scale Numerical Modeling

Inner Surface Morphology and Roughness Evolution of Pilgering Thick-Walled Tubes

Evolution of inner wall wrinkle defects in the sinking zone of a thick-walled steel tube during radial forging

Change in Surface Roughness on the Inner and Outer Surfaces of the Microtube during Hollow Sinking

Analysis and Control of Cracking and Wrinkling at the End of Seamless Steel Tube with Multi-Pass Large Deformation Diameter-Reducing

Effects of Forming Parameters on Deformation Uniformity of Thin-walled Parts during Multi-pass Spinning

Study on the Influence of Mandrel Speed on the Titanium Tube Continuous Retained-Mandrel Rolling Process

Analysis of Surface Orange Peel of Automotive Aluminum Alloy Pipe Using Electron Backscatter Diffraction (Ebsd)

Effect of Cold Rolling Degree on Texture Evolution, Eccentricity, and Yielding Anisotropy of GH4145 Alloy Tubes

Push-bending Process of Stainless-Steel Tubes: Experiment and Simulation

Influence of Roll Rotational Speed on inside Bore and Lamination Defects in Rotary Piercing Large Diameter Heavy Wall P92 Steel Pipe Process

Surface Roughening Analysis of Cold Drawn Tube Based on Macro–micro Coupling Finite Element Method

Microstructural evolution of external cold extrusion spinning 304 stainless steel with cumulative large deformation in multiple passes

Deformation behavior and load analysis of TP304 stainless steel billet during hot expansion process

Investigations on external separation layer defect of nickel-based superalloy in rotary tube piercing process

Influence of mechanical properties of tube on forming limits and deformation characteristics in expansion drawing process

Influence of process parameters on the flow forming quality of thin-walled tube with large diameter-thickness ratio

Investigation of the Bright and Dark Line on the Inner Wall of a Thin-Walled Copper Tube by Drawing with a Floating Plug