Abstract:In order to study the microstructure and property of cobalt based alloy layer cladding on the surface of ductile cast iron QT600-3 by laser, laser cladding of CoCrW alloy powder with the particle size of 46~106μm on the surface of QT600-3 was performed by 6 kW CO2 laser.Laser cladding process parameters were:laser power P=3.0 kW, scanning speed V=350 mm· min-1 , laser spot diameter 2 mm, lap ratio 1.5, three pass cladding, for which the thickness of cladding layer was about 3 mm.The temperature distri-bution of the cast iron sample was adjusted and controlled by the heat compensation during laser cladding processing.The microstruc-ture, composition, phases and hardness on the cross section of the cladding layer were investigated by Olympus metallurgical micro-scope ( OM) , Zeiss-Sigma scanning electron microscope ( SEM) , X′Pert MPD Pro X-ray diffraction ( XRD) and MHV2000 digital mi-cro hardness tester and the hardness changing was analyzed.The results showed that, the surface quality of the cladding layer was fine without crack, porosity and other defects;the cladding layer could be divided into melting zone, combined zone and heat affected zone, and it was integrated metallurgically with the ductile cast iron matrix, which was mainly composed ofγ-Co ( face centered cubic) solid solution and carbide of CoCx , Cr7 C3 , etc.The melting zone consisted of a surface layer of dendritic crystals and an internal layer of cellular crystals, and the transformation to the plate martensite occurred in the heat affected zone, where the globular graphite partially dissolved to the smaller graphite.The hardness of the cross section of the cladding layer increased rapidly and then increased gently with the increase of the distance from the surface of the graphite cast iron matrix, finally in the surface area rapidly increased.The maximum hardness of the cladding layer was HV0.21077, which was up to 4 times higher than that of the substrate of ductile cast iron.

Effect on Microstructure and Properties of Gray Cast Iron by Plasma and Laser Surface Alloying

Micro-plasma arc surface treatment of gray iron

Microstructure Evolution During Laser Cladding Fe-Cr Alloy Coatings on Ductile Cast Iron

Microstructure and Application of Surface after Laser Alloying on Surfacing Layer

Microstructural Properties of Particle-Reinforced Multilayer Systems of 316L and 430L Alloys on Gray Cast Iron

Effect Of Laser Melting Processing On The Microstructure And Wear-Resistance Of Gray Cast-Iron

Improving the Properties of Gray Cast Iron by Laser Surface Modification

Microstructure and Soil Wear Resistance of a Grey Cast Iron Alloy Reinforced with Ni and Cr Laser Coatings

Study on Friction and Wear of Cast Iron Friction Surface Layer by Laser Cladding

Microstructure and Property of Laser Cladding Cobalt Based Alloy Coatings on Ductile Cast Iron

On the Efficiency of Laser Alloying of Grey Cast Iron with Tungsten and Silicon Carbides

Fatigue Crack Propagation in Laser Alloyed Ductile Cast Iron Surface

Microstructure and corrosion resistance of laser alloying coating in-situ synthesized on ductile iron

Research on Laser Cladding Co-Based Alloy on the Surface of Vermicular Graphite Cast Iron

Microstructure Characteristics and Mechanical Properties of New-Type FeNiCr Laser Cladding Alloy Coating on Nodular Cast Iron

Microstructure and Properties of the Carburize-quenched Surface after Laser Alloying

Surface Remanufacturing of Ductile Cast Iron by Laser Cladding Ni-Cu Alloy Coatings

Laser Melting of Prefabrication AlOOH-Activated Film on the Surface of Nodular Cast Iron and Its Associated Properties

The Comparison of the Effects of Nodular Cast Iron Laser Alloying with Selected Substances

Enhancement of Mechanical Properties and Corrosion Resistance of Cast Iron Alloy Using CO2 Laser Surface Treatment

Study of the Microstructure and Corrosion Properties of a Ni-Based Alloy Coating Deposited onto the Surface of Ductile Cast Iron Using High-Speed Laser Cladding