Abstract:Abstract Nickel-based alloy coatings were widely used for the remanufacturing of dies and moulds by laser cladding, but the crack sensitivity would be increase due to the higher strength and hardness, which reduced the wear resistance of Ni-based alloys. In this paper, Ni-based coatings with the addition of a plastic phase (an austenitic stainless net) were prepared using laser cladding technology, and the CeO 2 was added in cladding layers. The cracking mechanism, microhardness, microstructure, phase composition, and wear properties were investigated. The relationship between thermal stress and the elastic and plastic fracture had been developed from the standpoint of fracture mechanics and thermal elastic fracture mechanics. The fracture criterion of the nickel-based coating was obtained, and the study has shown that the crack sensitivity could be reduced by decreasing the thermal expansion coefficient Δ α . Thus, a new method was proposed, which the stainless steel nets were prefabricated on the substrate. It was found that the number of cracks reduced significantly with the addition of stainless steel net. When the stainless steel net with 14 mesh was added in Ni-based coatings, the average microhardness of nickel composite coating was 565 HV 0.2 , which was 2.6 times higher than that of the 45 steel substrate. Although the rare earth oxide 4 wt.% CeO 2 and stainless steel net were added in the Ni-based coating reducing the microhardness (the average microhardness is 425 HV 0.2 ), the wear resistance of it improved substantially. The wear volume of Ni-based composite coating was 0.56×10 −5 mm 3 ·N −1 ·m −1 , which was 85.1% lower than that of 45 steel. The experiment results have shown that the Nickel-based composite coating is equipped with low crack sensitivity and high abrasive resistance with austenitic stainless net and the rare earth oxide 4 wt.% CeO 2 . This research offers an efficient solution to produce components with low crack susceptibility and high wear-resistance coatings fabricated by laser cladding.

Microstructure and corrosion resistance of laser alloying coating in-situ synthesized on ductile iron

Study of the Microstructure and Corrosion Properties of a Ni-Based Alloy Coating Deposited onto the Surface of Ductile Cast Iron Using High-Speed Laser Cladding

Laser Cladding Fe/FeCr Coatings on Continuous Casting Cu Mold

Microstructural evolution and corrosion properties of Ni-based alloy coatings fabricated by multi-layer laser cladding on cast iron

Repair feasibility and performance enhancement analysis of Fe-based alloy coating on ductile iron surface by high-speed laser cladding

Fatigue Crack Propagation in Laser Alloyed Ductile Cast Iron Surface

Corrosion and Wear Resistance Characteristics of Nicr Coating by Laser Alloying with Powder Feeding on Grey Iron Liner

Microstructural Properties of Particle-Reinforced Multilayer Systems of 316L and 430L Alloys on Gray Cast Iron

Effects of Laser Re-Melting and Annealing on Microstructure, Mechanical Property and Corrosion Resistance of Fe-Based Amorphous/Crystalline Composite Coating

Microstructure and properties of in situ synthesized Fe-Al coating by laser cladding

Investigation on Generating Ni-Based Composite Coatings Reinforced by Laser Cladding on the surface of Alloy Iron Exhaust Valve Ring

Research on Laser Cladding Co-Based Alloy on the Surface of Vermicular Graphite Cast Iron

Investigation on the Microstructure Evolution and Properties of a Novel In-Situ Fiber Phase-Reinforced Nickel Composite Coating Deposited by Wide-Band Laser

Semiconductor laser cladding of an Fe-based alloy on nodular cast iron

Effect of Different Particles Distribution on Microstructure and Corrosion Resistance of Nickel-Base Laser Cladding Coatings

Microstructures and corrosion resistance of Fe-based amorphous/nanocrystalline coating fabricated by laser cladding

Microstructure and Application of Surface after Laser Alloying on Surfacing Layer

Study on the Effect of Laser Remelting Energy Density on the Microstructure and Wear Resistance of Fe-Based Alloy Coatings Fabricated by Laser Cladding

Microstructural and Tribological Characteristics of Composites Obtained by Detonation Spraying of Iron-Based Alloy-Carbide Powder Mixtures

Study of Cracking Mechanism and Wear Resistance in Laser Cladding Coating of Ni-based Alloy

Microstructure and properties analysis of AlCoCrFeNi high-entropy alloy/iron-based amorphous composite coatings prepared by laser cladding