Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Microstructure and Properties of Submicro SiCp Reinforced 2014 Al-based Composites Fabricated by Semi-solid Extrusion

MICROSTRUCTURES AND PROPERTIES OF HOT-EXTRUDED SiCW/6061Al COMPOSITES

Forming process of hot-extruded SiCw/6061AI composites(I)

Experimental and Modeling Investigation on SiCp Distribution in Powder Metallurgy Processed SiCp/2024 Al Composites

Microstructures and Tensile Properties of Nano-Sized SiCp/Al-Cu Composites Fabricated by Semisolid Stirring Assisted with Hot Extrusion

Study on the powder mixing and semi-solid extrusion forming process of SiCp/2024Al composites

The Superior Ductility of Fine SiCp/Al2014 Composites after Extrusion

Microstructures and Tensile Properties of Al–Cu Matrix Composites Reinforced with Nano-Sized SiCp Fabricated by Semisolid Stirring Process

Effects of Stirring Time and Extrusion on Microstructures and Mechanical Properties of SiC Reinforced Pure Al Matrix Composites

Microstructures and Mechanical Properties of the Al2014 Composites Reinforced with Bimodal Sized SiC Particles

Influence of Hot Extrusion on Microstructure and Hardness of SiC Particle Reinforced Al-Zn-Mg-Cu Alloy Matrix Composite

Mechanical properties and microscopic analysis of SiCP/Al composites

Investigation of microstructures and mechanical properties of ultrafine SiC reinforced pure Al matrix composites

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Microstructures and Interface of C2/SiC Composites

Effect of Extrusion Temperature on the Microstructure and Mechanical Properties of SiCnw/2024Al Composite

Microstructural analysis of SiCp/Al composites

Regulating the Mechanical Properties of (μm B4C+nm SiC)/7075Al Composites Via Nano-Sic Content

Effects of die-pressing pressure and extrusion on the microstructures and mechanical properties of SiC reinforced pure aluminum composites

Effects of Sintering and Extrusion on the Microstructures and Mechanical Properties of a SiC/Al-Cu Composite

Effects of SiC Particle Pretreatment and Stirring Parameters on the Microstructure and Mechanical Properties of SiCp/Al–6.8Mg Composites Fabricated by Semi-Solid Stirring Technique