Abstract:In machining, heat concentration is generated at the surface contact between the tool and workpiece. This is the effect of hard frictions at the shear cutting plane to remove hard and brittle materials. The highly adhesive behavior of aluminum alloy 6061-T6 is more severe in higher cutting temperature, which may affect tool failures such as flank wear, tool chip and built-up edge, particularly on the edge of cutting inserts during the process. As a result, this may lead to the rough surface and low-dimensional accuracy of the machined parts. Realizing that metal-cutting industry players are demanding high-quality products with better surface finish and dimensional accuracy led to this study. Aluminum alloy 6061-T6 is a standard alloy used in automotive, aerospace and food packaging due to good hardness, high strength-to-weight ratio, resistance to corrosion and weldability. In order to address this problem, a newly developed metal working fluid which is SiO2-Al2O3-ZrO2 tri-hybrid nanofluid is applied in the cutting zone to achieve a good surface finish of the machined parts and lowering the cutting temperature. This study is the first attempt to enhance machining performance, particularly at high-speed machining, by employing a combination of tri-hybrid nanofluids and a minimum quantity lubricant technique. Industrial standards include uncoated tungsten carbide and CVD TiCN-Al2O3 carbide used during machining of aluminum alloy 6061-T6. The minimum quantity lubricant method is an alternative in supplying the lubricant into the machining zone due to flood machining and conventional fluid possess safety, health, economic and environmental effects. In this study, the experimental data were analyzed statistically using analysis of variance and response surface methodology. The responses studied were reduced significantly when tri-hybrid nanoparticles present at the cutting interface with higher MQL flow rate and concentration. There are two-factor interactions which are significant to the responses studied. Therefore, the combinations of MQL and excellent tri-hybrid nanofluids characteristics have enhanced between 16 and 76% of surface roughness and the cutting temperature, respectively, which is very promising in the future.

Adhesion Behavior and Mechanisms in High Speed Machining of Cellular Aluminum Alloy

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Three-dimensional numerical simulation for high speed milling of aerospace aluminum alloy

Research on 3D Numerical Simulation and Experiment of Cutting Temperature for High Speed Milling of Aerospace Aluminum Alloy

Research on the Machining Behaviors in High Speed Milling Cellular Aluminium Alloy

Chip morphology and cutting temperature of ADC12 aluminum alloy during high-speed milling

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Understanding The Deformation Of Metals In High Speed Cutting

Investigation of Chip Formation Mechanism and Surface Integrity in High Speed Milling Titanium Alloy

Serrated chip characteristics and formation mechanism in high-speed machining of selective laser melted Ti6Al4V alloys

Reducing the Adhesion Effect of Aluminum Alloy by Cutting Tools with Microgroove Texture

Surface Integrity Analysis on High Speed End Milling of 7075 Aluminum Alloy

Study and Modeling for Surface Roughness of Aluminum Alloy Milling

Experimental research on the dynamic characteristics of the cutting temperature in the process of high-speed milling

High Speed Milling Titanium Alloy With Respect To Cutting Tooth Number

High Speed Milling of Sic Particle Reinforced Aluminum-Based Mmc with Coated Carbide Inserts

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures

Effects of SiO2-Al2O3-ZrO2 Tri-hybrid Nanofluids on Surface Roughness and Cutting Temperature in End Milling Process of Aluminum Alloy 6061-T6 Using Uncoated and Coated Cutting Inserts with Minimal Quantity Lubricant Method

Research on surface integrity and its influencing factors in the high-speed cutting of typical aluminum/titanium/nickel alloys: a review

Experimental study on fracture mechanism transformation in chip segmentation of Ti-6Al-4V alloys during high-speed machining

Advancements in material removal mechanism and surface integrity of high speed metal cutting: A review