The Design Development of the Low-Temperature NormalP ressure and Large LPG Storage Tank

邢献军,杨必应,周晓清,吴燕生

DOI: https://doi.org/10.3969/j.issn.1001-4837.2001.01.014

2001-01-01

Abstract:This paper analysises the design and manufacturing of the low-temperature normal pressure and large LPG storage tank,and introduces the insp ection method,standards applied during the tanks were manufacturing.

What problem does this paper attempt to address?

DEVELOPMENT OF STRIP WINDING HIGH PRESSURE HYDROGEN STORAGE VESSEL WITH LOW STRESS INNER LINER

Shen Hairen,Zheng Chuanxiang

DOI: https://doi.org/10.3969/j.issn.1006-8805.2013.05.004

2013-01-01

Abstract:Safe storage and transportation of hydrogen is a key factor for the utilization of hydrogen energy.High-pressure hydrogen storage technology is still the main strategy in hydrogen storage and transportation,of which the high pressure hydrogen storage vessels are the key equipments.In this paper,the vessel strength on hoop and axial positions,pre-stress controlling of the cylinder,performance of corrosion resistance are analyzed in detail through an applied example of high pressure hydrogen storage vessel,which provides reference for designers.
Analysis of field test on the foundation of a large oil tank

应宏伟,杨晓刚,卞守中,潘秋元,谢康和

DOI: https://doi.org/10.3321/j.issn:1000-4548.2005.02.005

2005-01-01

Abstract:This paper presents experimental data obtained during the construction and loading test of an oil tank , which was constructed by SINOPEC Maoming Petrochemical Company. Currently, this oil tank is the largest in China. The tank was founded on loose sand improved with stone columns. Pressure cell and piezometers were used to monitor soil stresses and pore pressures respectively. At the same time the deformation of the soil foundation was observed. The obtained result was analyzed thoroughly.
Design of Thermal Insulation for Lng Tanker

ZC Li,H Sun,L Xu,J Zhang

DOI: https://doi.org/10.3321/j.issn:1000-0976.2004.02.026

2004-01-01

Abstract:The LNG tanker is very important transport equipment in LNG transmission for its flexibility and ecumenical. In this paper, the principle of the high vacuum-multilayer thermal insulation were intruded and compared with vacuum-powders insulation and high vacuum insulation. It is very suitable for tanker for its characteristics as small thermal conductivity and small volume. The design and calculation of thermal structure for a 40 m 3 LNG tank used in tanker were presented. The the non-loss storage time for the tank was calculated.
Research of Large LNG Tank Structure

Ting Ke Li,Jia Di Li,Li Fu Xiao,Wei Li

DOI: https://doi.org/10.4028/www.scientific.net/amr.1070-1072.378

2014-01-01

Advanced Materials Research

Abstract:In recent years, the demand of Large LNG storage tank increases over time, but large LNG cryogenic storage tank has not yet established a series of standards and norms, and tank construction technology is also lagging behind. Aiming at the design of the tank form a single, smaller, did not tackle the issue of, this paper mainly discusses from Large LNG tanks, such as type, material selection, structure ,size optimization and so on, which can provide reference for independent construction of storage tank.
Design and summary of 1000m~3 low-temperature spherical tank for oxygen storage

LI Fu-lu

Abstract:The 1 000 m~3 low-temperature spherical tank for oxygen storage is the biggest one ever designed,manufactured,assembled and welded in China.The material selection,detail structure,etc.are discussed.

Engineering,Environmental Science,Materials Science
A Study of the Fire Design of Large Liquefied Gas Storage Tank

Xiao-xia GE,Xi-lin DONG,Qi-yun GUO

DOI: https://doi.org/10.3969/j.issn.1009-0029.2008.02.007

2008-01-01

Fire Science and Technology

Abstract:Storage form was analyzed by physical chemistry character of liquefied gas.Potential fire danger of liquefied gas storage tank was summarized.On the basis of these,key points of fire design about technics design, layout,fire protection and fire fighting measure were put forward,and facts affecting tank accident and fire protection were summarized by fishbone diagram.It was beneficial to the engineering.
The Design Of Ultra-Large Hydraulic-Balance Oil Tank With Double-Shell

Guowei Cao,Zhiping Chen,Wenjing Guo

DOI: https://doi.org/10.1115/PVP2011-57186

2012-01-01

Abstract:Large-scale oil tanks are being studied all along because they have a series of advantages. For example, they can reduce the cost of manufacturing and management of the facilities, and save land. So the volume of oil tanks becomes larger and larger during their development. However, without on-site heat treatment, the thickness of the shell of traditional oil tanks is restricted to 200,000 m(3). In this paper, a new structure named Ultra-large Hydraulic-Balance oil tank with double-shell was put forward. With the method of hydraulic-balance, oil tanks of this structure could be larger than 200,000 m(3). Besides expounding the working principle in detail, a 200,000 m(3) oil tank with double-shell was also designed in the paper according to API 650, and the finite element model was used to analyze the stress including intensity and distribution of both shells in order to test and verify its security. Furthermore, its economy was analyzed by comparing with traditional oil tanks. Finally, the problem caused by the difference of liquid lever as well as was discussed. Results show that Ultra-large Hydraulic-Balance oil tank with double-shell owned advantages including rational construction, economy and easy manufacturing.
Stress testing and analysis of 105m3 crude oil tank

刘育明,陈志平,吴晓滨,李晓红,章烈

DOI: https://doi.org/10.3969/j.issn.1001-4578.2001.03.010

2001-01-01

Abstract:The crude oil tank with a capacity of 105m3 is the largest oil tank at present in China. To learn the distribution of stress in the fillet weld and the first and second layers of the tank, and to verify whether the design is rational and operation is safe, stress test and evaluation were made on one of the tanks. The test was conducted by the static resistance stress-strain method based on the specified on-the-spot conditions. Analysis and calculation show that, the measured value of the circumferential stress on the outer surface of the tank is consistent to the calculated value, and the maximum stress occurs near the upside of the junction of the tank's first and second layer. The tank is evaluated based on the design rules, and the result proves that the tank is designed rationally and its strength meets the need of operation.
Key Technologies of Large LNG Storage Tanks

YIN Jinsong,MA Xiaohong,CHEN Shuping

DOI: https://doi.org/10.3969/j.issn.1000-4416.2011.07.015

2011-01-01

Abstract:The manufacturing standard,material,design,welding,insulation,construction of large LNG storage tanks are described.The strength and toughness of 9Ni steel may be improved by refining the grain,increasing the purity and adding alloy elements.The improper welding of 9Ni steel may cause arc magnetic blow,welding cracks and poor low-temperature toughness of welding joint,which can be solved by selecting proper welding material,minimizing the arc crater and controlling the welding heat input.For the special structure and insulation of large LNG storage tanks,it is necessary to make a detailed structure design and calculation,select appropriate insulation materials and construction scheme.To enhance the construction level as early as possible,it is urgent to make a domestic standard of large LNG storage tanks.
Optimization Analysis On The Structure Parameters Of A 20x10(4)M(3) Ultra-Large Tank For Crude Oil Storage

Wenzhuo Feng,Zhiping Chen,Xinliang Shen,Fan Zhou,Haigui Fan

DOI: https://doi.org/10.1115/PVP2013-97758

2014-01-01

Abstract:With the advantages of low investment, small footprint, ease of operation management etc., large-scale vertical tanks for crude oil storage have become an obvious trend. However, stress intensity of the tank wall increases with constant enlargement of oil tank's parameters, and the yield strength of the steel used as tank wall material can not be more than 490 MPa. Besides, the maximum thickness of shell plate generally should be not over 45 mm subjected to the restriction of manufacturing process. So, it is important to design the structure of tank, reasonably and reduce the stress as much as possible. This paper combines theoretical analysis and numerical simulation together, analyzing and calculating the stress of shell plate and bottom plate of an ultra-large tank for crude oil storage which is 200000 cubic meters, and comparing the stress level of three design schemes about shell plate and bottom annular plate, then giving a scheme whose stress distribution is more reasonable. The study shows that combined cylindrical shell method is applicable to the theoretical stress calculation of shell plates of ultra-large crude oil storage tanks, finite element method using contact element could simulate the stress distribution of bottom plate well, and give the optimal structure parameter scheme by controlling the hoop stress of tank wall and radial stress of bottom plate. The result of this paper has a certain practical guiding significance to the optimization design of ultra-large tanks for crude oil storage.
Structure Design and Stability Calculation of Large Storage Tanks with a Reticulated Shell Dome

CHEN Zhiping,FENG Wenzhuo,LIU Lige,GAO Huan

DOI: https://doi.org/10.3901/jme.2015.06.036

2015-01-01

Journal of Mechanical Engineering

Abstract:With the large-scale development of refined oil storage tanks, adopting spatial reticulated hell structures as the tank dome is becoming an inevitable trend. Although reticulated shell structures have mature theory and design experience in the field of architecture, there are still many technical problems about its application in large storage tanks. The advantages and disadvantages of existing large reticulated shell structures are analyzed and compared and the selection opinions of grid type, bar section and node form are given against the structural features of large storage tanks with a reticulated shell. In order to improve the connection security of the reticulated shell and lower tank body, a new bearing structure is proposed which is applicable for large storage tanks with a reticulated shell. The calculation method for overall stability of reticulated shell dome is discussed, the critical buckling load will be calculated by the method of whole process analysis of load-displacement considering geometric nonlinearity, and the influence of lower tank body, different constraint conditions and installation deviations on the stability capacity of a reticulated shell dome. Moreover,a 50 000 m3 large storage tank with a reticulated shell is used as an example to conduct case analysis according to related standards, such as JGJ7-2010 Technical specification for space frame structures, which verities that relevant specifications are also applicable for tank reticulated shells.
Optimization Analysis on the Structure Parameters of a 20×104 m3 Ultra-Large Tank for Crude Oil Storage

Wenzhuo Feng,Zhiping Chen,Xinliang Shen,Fan Zhou,Haigui Fan

DOI: https://doi.org/10.1115/pvp2013-97758

2013-01-01

Abstract:With the advantages of low investment, small footprint, ease of operation management etc., large-scale vertical tanks for crude oil storage have become an obvious trend. However, stress intensity of the tank wall increases with constant enlargement of oil tank’s parameters, and the yield strength of the steel used as tank wall material can not be more than 490 MPa. Besides, the maximum thickness of shell plate generally should be not over 45 mm subjected to the restriction of manufacturing process. So, it is important to design the structure of tank reasonably and reduce the stress as much as possible. This paper combines theoretical analysis and numerical simulation together, analyzing and calculating the stress of shell plate and bottom plate of an ultra-large tank for crude oil storage which is 200000 cubic meters, and comparing the stress level of three design schemes about shell plate and bottom annular plate, then giving a scheme whose stress distribution is more reasonable. The study shows that combined cylindrical shell method is applicable to the theoretical stress calculation of shell plates of ultra-large crude oil storage tanks, finite element method using contact element could simulate the stress distribution of bottom plate well, and give the optimal structure parameter scheme by controlling the hoop stress of tank wall and radial stress of bottom plate. The result of this paper has a certain practical guiding significance to the optimization design of ultra-large tanks for crude oil storage.
Comprehensive Design and Preliminary Experiments of Liquid Hydrogen Storage Tank for Trucks

Chuancong Wan,Chaoyue Shi,Shaolong Zhu,Song Fang,Limin Qiu,Guoyou Shi,Dingfu Li,Shouqiang Shao,Kai Wang

DOI: https://doi.org/10.1016/j.ijrefrig.2024.10.037

IF: 4.14

2024-11-06

International Journal of Refrigeration

Abstract:As the global demand for lower carbon emissions intensifies, the deployment of medium and small-scale liquid hydrogen (LH2) storage tanks in heavy-duty trucking and aviation is expected to increase. However, heat leakage into these cryogenic vessels leads to a continuous increase in tank pressure, potentially resulting in sudden hydrogen release and other safety concerns. While horizontal LH2 tanks demonstrate greater suitability in the transportation sector compared to vertical tanks, investigations in this domain remain scarce. Research on horizontal tanks is crucial for safe and efficient storage. Understanding these dynamics is essential for predicting temperature and pressure changes during self-pressurization, ensuring safe liquid hydrogen storage. This study designed and built a 500-liter horizontal liquid hydrogen tank for vehicle fuel storage, following ISO 13985 standards to ensure practical applicability. The project encompassed material selection, structural design, and both stress and thermodynamic analyses. Preliminary experiments were conducted using liquid nitrogen as a substitute for liquid hydrogen. Experiments assessed tank heat leakage, vapor-cooled shield insulation performance, thermal stratification, lossless storage time, and pressure changes during self-pressurization and steady-state evaporation. Results validate the efficiency of our pressure vessel design method for complex conditions, enhancing understanding of self-pressurization and thermal stratification in horizontal tanks. The vapor-cooled shield reduced heat leakage into the tank by 22.7%, decreasing the daily evaporation rate under liquid nitrogen conditions from 1.87 wt% to 1.5 wt%. and maintaining an initial liquid level of 50% extended the lossless storage time to 50 hours in the LN2 scenario. These findings offer valuable insights for assessing the performance of subsequent liquid hydrogen experiments.

engineering, mechanical,thermodynamics
Study on Cold Insulation Construction Technology of LNG Low Temperature Storage Tank Wall

Xuan-Yu Sheng,Jun-Man Shu,Jian Chen,Hui-Zhen Tian,Chen Ling

DOI: https://doi.org/10.12783/dtssehs/mess2017/12117

2017-01-01

Abstract:The cold insulation construction of LNG low-temperature storage tank is the key process of construction of tank shell and the cold insulation construction of tank wall is both the key point and the difficult point of cold insulation construction. The cold insulation layer of tank wall has characteristics of complicated structure design, frequent overhead operation and high-standard installation, strictly abiding by stipulated procedure. Technique requirements during construction and solution to problems of safety and high efficiency during the entire process of construction and control of construction quality are important guarantees of carrying out cold insulation construction of LNG low-temperature storage tank wall smoothly. This paper cites simulation of cold insulation of LNG low-temperature storage tank wall as example and describes detail contents of structural characteristics of cold insulation layer of tank wall, construction procedures and construction methods.
Finite element analysis of strength of mobile cryogenic LNG storage tank

Xu Miaofu,Liu Baoqing,Jiang Jialing,Jin Zhijiang

DOI: https://doi.org/10.3969/j.issn.1000-6516.2010.01.003

IF: 2.134

2010-01-01

Cryogenics

Abstract:In order to achieve the optimum design and safe operation,the mobile cryogenic LNG storage tank with high-vacuum multilayer insulation was researched with the help of finite element method on the basis of analyzing the features of structure and load The distributions of its global and local stress intensity corresponding to the behaviours of startup,brake and bumpiness,etc were also obtained.The results show the inwall of inner vessel near lower sliding support is the place with the highest stress intensity under multiple conditions,especially under bumpiness,the maximum stress intensity is above 323.5 MPa and 62.5% higher than under static condition,so the stiffening rings with proper thickness and spacing should be situated on the inner and outer vessel of LNG storage tank to decrease the local stress intensity.In addition,the fatigue analysis and assessment,which is done against the alternation of horizontal acceleration between 0.5 g and 1.0 g,show the present structure of mobile LNG storage tank meets the requirements of fatigue strength.Simultaneously it is also found that the maximum alternate stress intensity occurs at the edge of stiffening ring near fixed support,which indicates the destruction to membrane stress system due to structure discontinuation is the major cause of fatigue failure,thus the mobile cryogenic LNG storage tank with rounding off structure is recommended.
Comparison of the Strength Design and Prevention Method of Elephant Foot Buckling among Countries' Standards of Oil Tanks

Zhiping Chen,Bo Sun,Chulin Yu,Zhou Fang,Ming Zeng

DOI: https://doi.org/10.1115/pvp2009-77608

2009-01-01

Abstract:In China a large number of tanks whose volumes are greater than 100000 m(3) are necessary to be built for establishing the oil reserves system with four levels, which include national strategic oil reserve, commercial oil reserves in the three major oil companies, oil reserves in local governments and general enterprises. Oil tanks built in China were mostly welded tanks and on the ground. The difference among the methods of the strength design of the tank side plate designed by countries' standards such as API 650 JIS B 8501 BS EN 14015 and GB 50341 is discussed. And the reason why API 650 is used by China engineering company is given. Then kinds of prevention methods about the tank wall elephant foot buckling by earthquake which were designed according to different national standards are compared. It is pointed out that the calculation methods of the tank wall's allowable compressive stresses and longititude compressive stresses designed by national standards are different. At last the existing problems and the appropriate solutions are analyzed briefly.
Design Risk Evaluation Analysis of the LPG Storage

TAO Shan-ju,CHEN Guang-zhao,CHEN Yan,ZHENG Guo-qiu

DOI: https://doi.org/10.3969/j.issn.1001-9677.2011.13.078

2011-01-01

Abstract:The effect of failure modes and mechanisms risk to the safty and life should be pre-considered for pressure vessel design.By ration select material,configuration improvement,manufacture technics optimization,through controling and decreasing the risk of pressure vessel during usage in the design and early manufacture,with measures from the process,the safe life can achieve the desired.
Overall Temperature Field and Thermal Stress Analysis of 30000m(3) LNG Storage Tanks

Hong-Zhi Zhang,Guo-Rui Zhang,Bing Ge,Jian Chen,Xuan-Yu Sheng,Ling Chen

DOI: https://doi.org/10.1142/9789813228177_0148

2018-01-01

Abstract:CATIA software is used to build two-dimensional and three-dimensional model of LNG storage tank, hexahedral meshes are generated in HYPERMESH software and ANSYS software is imported to analyze overall temperature field and thermal stress distribution of 30000m(3) LNG storage tank. According to analysis result file, the distribution regularities of temperature and thermal stress of 30000 m(3) LNG storage tank is concluded, key control points of cold insulation construction of LNG storage tank are highlighted, management of quality of cold insulation construction of LNG storage tank is tightened up and LNG construction level is upgraded.
THERMAL RESPONSE OF LPG STORAGE TANK EXPOSED TO FIRE AND THE FIRE-PROTECTION DESIGN

邢志祥,韩军利,蒋军成

DOI: https://doi.org/10.3969/j.issn.1002-106X.2004.02.017

2004-01-01

Abstract:Thermal response variation rules of LPG storage tank exposed to fire are expounded. It is suggested that water supply intensity in the fire-protection design shall be reassessed and determined through experiments. Water overflow in the top of tank combined with fixed water gun is suitable for fixed storage tank, and the safe valve with appropriate size shall be set simultaneously. Moving water gun is suitable for large-scale storage tank. As for the moving storage tank, insulating coat together with pressure relieving safe valve are suggested to be adopted.
Research And Development Of A Double Steel Bottom Structure Of Oil Storage Tank

Zhiping Chen,Liuchuan Yan,Zhou Fang,GuoWei Cao

DOI: https://doi.org/10.1115/PVP2010-25537

2010-01-01

Abstract:Oil and gas leak accidents occur sometimes for the sever corrosion of existing large steel oil storage tanks with single bottom and the leak is not easily found. So a double steel bottom structure was proposed in this paper, which mainly consisted of a primary bottom, a secondary bottom, support components between the two bottoms and a leak monitoring device. The sealed containment space formed by the two bottoms could prevent leaking oil and gas from polluting the environment. And timely leak forecast would be available by detecting its internal gas compositions on line. 6 different support arrangements were given in this paper with a small test tank as an example. Finite element method was adopted to analyze the stress distribution on each bottom. And one of the 6 support arrangements with a suitable arrangement manner and angle steel amount was chosen as the final support arrangement of the test tank after a comprehensive consideration of stress level, deformation degree, angle steel weight and the ease of manufacture and so on.

The Design Development of the Low-Temperature NormalP ressure and Large LPG Storage Tank

DEVELOPMENT OF STRIP WINDING HIGH PRESSURE HYDROGEN STORAGE VESSEL WITH LOW STRESS INNER LINER

Analysis of field test on the foundation of a large oil tank

Design of Thermal Insulation for Lng Tanker

Research of Large LNG Tank Structure

Design and summary of 1000m~3 low-temperature spherical tank for oxygen storage

A Study of the Fire Design of Large Liquefied Gas Storage Tank

The Design Of Ultra-Large Hydraulic-Balance Oil Tank With Double-Shell

Stress testing and analysis of 105m3 crude oil tank

Key Technologies of Large LNG Storage Tanks

Optimization Analysis On The Structure Parameters Of A 20x10(4)M(3) Ultra-Large Tank For Crude Oil Storage

Structure Design and Stability Calculation of Large Storage Tanks with a Reticulated Shell Dome

Optimization Analysis on the Structure Parameters of a 20×104 m3 Ultra-Large Tank for Crude Oil Storage

Comprehensive Design and Preliminary Experiments of Liquid Hydrogen Storage Tank for Trucks

Study on Cold Insulation Construction Technology of LNG Low Temperature Storage Tank Wall

Finite element analysis of strength of mobile cryogenic LNG storage tank

Comparison of the Strength Design and Prevention Method of Elephant Foot Buckling among Countries' Standards of Oil Tanks

Design Risk Evaluation Analysis of the LPG Storage

Overall Temperature Field and Thermal Stress Analysis of 30000m(3) LNG Storage Tanks

THERMAL RESPONSE OF LPG STORAGE TANK EXPOSED TO FIRE AND THE FIRE-PROTECTION DESIGN

Research And Development Of A Double Steel Bottom Structure Of Oil Storage Tank