In-Pipe Detection of Three-Dimensional Curving Mini-Pipe

MAO Yi-tian,Ke Ying-lin,LI Jiang-xiong

DOI: https://doi.org/10.3321/j.issn:1003-8728.2005.06.008

2005-01-01

Abstract:We present a new method for in-pipe robot control, and introduce 3 kinds of sensors attached to the in-pipe robot. These sensors were used to measure the curvature of pipe, to position the mini-robot, and to get the image of the inside surface of the pipe.

What problem does this paper attempt to address?

Photoelectric Detection and 3D Reconstruction System for the Inner Surface of Small-Diameter Pipes

WU En-qi,KE Ying-lin,LI Jiang-xiong

DOI: https://doi.org/10.3969/j.issn.1003-501x.2007.01.014

2007-01-01

Abstract:A detection and three-dimensional reconstruction system for the interior surface of small-diameter pipes was presented based on Position Sensitive Detector (PSD) and optical triangulation principle. The system consisted of an in-pipe micro-robot, a profile detection sensor, a curvature sensor and so on. The profile inspection sensor caught the point position of the inner surface section in the local coordinates when it moved in pipe driven by the robot. At the same time, the curvature sensor got the local geometric information of the central axis of pipe in the sampling position and reconstructed the central axis. Finally, the inner surface of the pipe was reconstructed according to the data of the two sensors and the step of the robot. Experimental results show that the relative measurement accuracy of the pipe curvature is ±2%, and the measurement accuracy of inner surface defect and inner diameter are ±0.1mm respectively.
3D Reconstruction of Small-diameter Pipes Inner Surface Based on Structural Light

Jiangxiong Li,Enqi Wu,Yinglin Ke

DOI: https://doi.org/10.3321/j.issn:0254-3087.2006.03.009

2006-01-01

Abstract:A 3D reconstruction system for the interior surface of small-diameter pipes is developed. The system consists of an in-pipe micro-robot, a profile detector and a curvature sensor. The profile detector captures sectional pictures of the inner surface when it moves in a pipe driven by the robot. At the same time, the curvature sensor gets the local geometric information of the central axis of the pipe in the sampling position. The image coordinates of points in the sectional pictures are obtained through adaptive image processing. Then three-dimensional coordinates of the points in the profile detector's local coordinate system can be calculated according to the calibration and structure parameters of the detector. Meanwhile, the relationship between every local coordinate and the global one can be derived based on the corresponding local geometric information of the central axis and the step of the robot. The coordinates of the points in all the measured sections can be transformed into global ones and the 3D profile of the inner surface of the pipe can be reconstructed easily by reverse engineering. As shown by the experiments, the reconstructed 3D profile is coincident with the actual facts.
Noncontact Laser Inspection Based on a PSD for the Inner Surface of Minidiameter Pipes.

Enqi Wu,Yinglin Ke,Baojiang Du

DOI: https://doi.org/10.1109/tim.2008.2006727

IF: 5.6

2008-01-01

IEEE Transactions on Instrumentation and Measurement

Abstract:A new noncontact laser-inspection technique based on a position-sensitive detector (PSD) to inspect the inner surface of minidiameter pipes is proposed, and the corresponding sensor is developed. A light spot is projected onto the pipe inner wall after the laser beam is reflected by two mirrors. At the same time, four current signals are produced when the light spot is read by the 2-D PSD. According to the magnitude of the current signals and the structure parameters of the sensor, the spot position on the inner wall can be calculated in a local 3-D coordinate system. With a micromotor, the surface of the whole inner wall can be scanned by the laser beam. This way, the coordinates of all the sample points in the section are obtained. After that, several reasonable data-processing methods are used, such as data segmentation and least squares fitting. Finally, the section curve can be reconstructed. The radius and defects of the section can also be obtained. Driven by a micropipe robot, the sensor can inspect a long curved pipe. The inspection system based on this technique can detect the inner surface of minidiameter pipes, which has an inner diameter of 9.5-10.5 mm and a curvature radius of more than 100 mm. The measurement accuracy of this inspection system for the inner diameter and surface defect reaches plusmn0.1 mm.
New Inner Surface Profile Sensor for Mini-Diameter Pipes

LI Jiang-xiong,WU En-qi,KE Ying-lin

DOI: https://doi.org/10.3785/j.issn.1008-973x.2006.09.032

2006-01-01

Abstract:For inspecting the 3D shape and appearance of the inner surface of long and tiny pipe,a new type of sensor was proposed based on the principle of optical triangulation.The working principle of the sensor was introduced,and a model was built to express the relation between the position of the laser spot on the sensitive surface of the position sensitive device(PSD) and the corresponding point on the inner-surface of the inspected pipe.After the ray path of the sensor was designed according to the principle of making the sensor to be shortest,an eliminating method of system structure error was studied,and the signal acquiring circuit and processing method were designed to overcome the impact of PSD dark current with laser signal modulation method.The results show that the proposed sensor with 37.5 mm in length,7 mm in diameter and 4 g in weight can inspect the 3D shape and appearance of the inner pipe surface with interior diameter of 9.5～10.5 mm.The measurement error of the proposed sensor is-0.1～ 0.1 mm.
Non-Contact Inspection for Inner Surface of Small-Diameter Pipes Based on Laser-Psd

Wu En-qi,Ke Ying-lin,Li Jiang-xiong

DOI: https://doi.org/10.1007/bf03033619

2005-01-01

Optoelectronics Letters

Abstract:A new non-contact inspection technique based on laser-PSD (position sensitive detector) to inspect the inner surface of small-diameter pipe is proposed, and the corresponding sensor has been developed. After being reflected by two mirrors in series, a laser beam is projected onto the inner wall of a pipe as a small light spot and is read by a two-dimensional PSD. Based on the signals from the PSD and the structure parameters of the sensor, the spot position on the wall can be calculated in a local 3D coordinate system. The spot controlled by the micro-motor driven mirrors will scan a closed section ring on the inner wall of the pipe to obtain the relative coordinates of all the sampled points. The data will be then processed through data segmentation and least square fitting, to reconstruct the section curve used for obtaining the radius and the defect description of the section. Driven by a micro-pipe robot, the sensor can inspect a long curved pipe and obtain its 3-D reconstruction. An inspection system based on this technique can detect the mini-diameter pipe with an inner diameter of 9.5 mm≈10.5 mm and a curvature radius larger than 100 mm at a measurement accuracy of the inner surface defect of ±0.1 mm.
Local Geometric Measurement for 3-D Curved Micro-Pipe

金成柱,李江雄,柯映林

DOI: https://doi.org/10.3969/j.issn.1003-501x.2004.08.014

2004-01-01

Abstract:A sensor and a measuring system for inspection local geometric property of 3D micro-pipe are developed. During the pipe robot slip type testing process, robot can automatically adapt the geometric shapes of the pipe and its internal optical path will also be changed. The rotation rate of the frenet frame set on pipe sensor along the axis is determined based on the illumination position of laser beam on PSD light-sensitive plane and sensor structural parameters. In this way the position relation between two adja- cent frenet frames is obtained. Combined with the initial position of the frenet frame and sensor structure, the local geometric parameters of the pipe central line can be calculated by using recurrence algorithm. The experimental results show that its relative measuring error is less than 4%,and it is suitable for measuring geometric property of f10~f13mm pipes with a curvature radius more than 100mm.
Application Research of Three-Dimensional Technology Aided Design of New Pipe Inserting into Underground Pipe

Tao WANG,Yi ZHANG,Ying XU

DOI: https://doi.org/10.3969/j.issn.1673-6338.2014.05.015

2014-01-01

Abstract:A method based on three-dimensional technology to aided design of new pipe inserting into underground water supply and drainage pipe has been researched on. Because of its distinct curvature and multiple distortions, the spatial model is very complex, so the general three-dimensional pipe design software can’ t be used in this pro-ject. The unreliability will be existed if the planar design is on the basis of the profile diagram. Therefore, the com-puter three-dimensional graphics technology can be a feasible solution to this problem. The maximum diameter of new pipe is obtained by using the three-dimensional object collision detection. Three-dimensional arc fitting based on spherical linear quaternion interpolation was adopted and three-dimensional modeling of complex pipe was real-ized. The adopted object collision detection algorithm based on triangle unit is simple and applicative. A modeling and collision demonstration software based on OpenSceneGraph three-dimensional engineer was developed to in-spect and verify a design project, the correctness of the method was confirmed by the result.
Panoramic Optical Annular Staring Inspection System for Evaluating the Inner Surface of a Pipe

Zhao Liefeng,Feng Huajun,Bai Jian,Jin Hao

DOI: https://doi.org/10.1117/12.755838

2008-01-01

Abstract:There should be flaws and defects on the inner surface during the producing period of a pipe, as well as contaminations and corrosions during the using period of it. A corresponding panoramic optical annular staring inspection system has been developed. It requires no rotating mechanism to exam the whole circumference of a cross section of the inner pipe surface at once, which results high speed inspection.There are two main subsystems in this inspection system, the panoramic optical annular staring imaging subsystem and driving robot subsystem. The Flat Cylinder Perspective (FCP) is the principle to image a panoramic annular view to a flat imagery, i.e. a cylinder of vision imaged is flat. Our imaging subsystem includes a panoramic annular lens (PAL), which is critical and used to implement the FCP, a series of image rotation lenses, a charge-coupled device (CCD) camera, and an illuminating light-emitting diode (LED) ring. The CCD camera sending the signal to a personal computer (PC) via VGA signal results a real time inspection.The driving robot subsystem is a fine designed complicated mechanism including a subassembly of stepper motor. It can drive the inspection system forward and backward continuously in the pipe along the axial direction. The experimental system reported in this paper has the following specifications: average detection resolution of 0.5 mm at the circumference direction and 1.0 mm at the axial direction of a pipe, and inspection speed of 15 mm/s.
In-pipe Positioning Micro-Robot Based on Cymbal Actuators and Optical Navigation

LI Jiang-xiong,GUO Tong,KE Ying-lin

DOI: https://doi.org/10.3785/j.issn.1008-973x.2006.06.002

2006-01-01

Abstract:In order to improve loading capacity and moving speed of in-pipe micro-robot,and to make the robot perceive displacement of itself,a kind of inpipe micro-robot based on piezoelectric cymbal actuators and optical navigation technology was developed.The locomotive device of the proposed robot was designed with Φ8 mm piezoelectric cymbal actuators.The kinetic model of the locomotive device was built and verified with finite element method and experiment.The self-displacement inspection unit of the robot was designed with optical navigation chip based on rapid image acquiring and processing technologies.Experimental results show that the robot's locomotive device can load as 4 times its weight,and that the robot's speed can be increased to 41.7 mm/s.The self-displacement inspection unit can inspect the displacement of the linear movement and rotation of the robot in the pipe.The inspecting accuracy of the unit is up to 0.3%.
Development of a 3D Pipe Robot for Smart Sensing and Inspection Using 3D Printing Technology

Wen-Chung Chang,Yang-Cheng Huang,Pei-Ying Chang

DOI: https://doi.org/10.1080/23080477.2017.1338428

2017-06-16

Smart Science

Abstract:This 3D pipe inspection robot is capable of conducting fully autonomous pipe inspection, transmitting measured data to the monitoring end by wireless communication, drawing a 3D pipe routing map in real time, and detecting pipe anomalies. The robot is both lightweight and inexpensive because it is constructed by 3D printing. The main functions of the robot include calculating the robot posture using the measurements from the accelerometer and gyroscope module, drawing a 3D pipe routing map in real time, deciding the degree of contraction from pressure sensor module readings to detect abnormal expansion or contraction, and locating potential hazards in the pipe. The robot described in this paper is different from others in many ways. The freely extendable and contractible body structure allows the robot to easily adapt to pipes of various diameters. The wireless IP camera onboard transmits real-time videos and assists operators in looking for signs of damage or anomalies. This robot is practical and can be used for the inspection of damaged pipes, redrawing 3D pipe routing maps, and assisting in the regular maintenance of pipes underground or located within buildings, and may also be of use in rescue work and disasters, etc.
Study on Total Distance Positioning of In-Pipe Robot -Based on Fiber Bragg Grating Curvature Spatial Sensor

刘刚,柯映林

DOI: https://doi.org/10.3785/j.issn.1008-973x.2004.06.007

2004-01-01

Abstract:A recurrence algorithm based on fiber Bragg grating curvature spatial sensor for total distance positioning of in-pipe robot was presented. Curvature and inclination of adjacent osculating plane of current point were obtained by curvature spatial sensor. Then the current point's coordinates were calculated according to position, osculating plane, tangent direction of the former point and step length of the in-pipe micro-robot. In this algorithm, the total distance positioning of the in-pipe robot was realized if position, curvature and tangent direction of the origination point were known. At the same time, the central coordinates tracked by the in-pipe robot were calculated and the orbit curve was fitted by B-spline algorithm. With the orbit curve and the correlative measured section, 3D reconstruction of the inner surface can be achieved.
A Study On The System Of The In-Pipe Robot

H Ma,Yg Li,Sp Bai,Df Li

2005-01-01

Abstract:The paper presents a robot system which detect the crack, the blowhole, the weld joint, the defect etc and the pipe's diameter can be detected varying from 95 59mm to phi 70mm. The information of image is propagated by wireless or wire method to the monitor for observing the image of inner face of pipe in time.
Design and Development of a Deformable In-Pipe Inspection Robot for Various Diameter Pipes

Zhixuan Liang,Jiannong Cao,Zhiqin Cheng,Huafeng Xu,Jinlin Chen

DOI: https://doi.org/10.1109/IROS55552.2023.10341512

2023-10-01

Abstract:Pipelines have become one of the most important infrastructures in the city. Over time, they are prone to aging, cracks, corrosion, and the demand for regular inspection is gradually increasing. Robotic solutions are effective methods for in-pipe inspection. However, existing In-pipe Inspection Robots (IPIR) require that the inner diameter of the pipe is fixed in the application scenarios, and need extra labor to control the robot and handle the cable. In this work, we design and develop a deformable robot to adapt to pipes with different inner diameters. Specifically, the passive elastic hinge is used by us to make the robot fully in contact with the pipe, generating enough friction to ensure that the robot is attached to the inner wall of the pipe. An edge device is deployed on the robot, generating velocity commands of wheels through the data from Inertial Measurement Unit (IMU), which eliminates the need for external devices. Experimental results demonstrate that the robot can move in horizontal and vertical pipelines, as well as traverse through pipe joints and scenarios where there is dirty or small obstacle.

Computer Science,Engineering,Environmental Science
Development of an In-Pipe Robot with Differential Screw Angles for Curved Pipes and Vertical Straight Pipes

Te Li,Shugen Ma,Bin Li,Minghui Wang,Zhiqiang Li,Yongqing Wang

DOI: https://doi.org/10.1115/1.4037617

2017-01-01

Journal of Mechanisms and Robotics

Abstract:The in-pipe robots based on screw drive mechanism are very promising in the aspects of pipe inspecting and maintaining. The novel design of an in-pipe robot with differential screw angles is presented for the curved pipes and vertical straight pipes. The robot is mainly composed of the screw drive mechanism, adaptive linkage mechanism, and the elastic arm mechanism. The alternative adjusting abilities of the mobile velocity and traction, and the adaptive steering ability in curved pipes, are achieved by the special designs. A parameter design approach in consideration of the climbing and steering abilities is proposed in detail for the springs and length of the elastic arms. The results are applied to the prototype design of the robot. In several groups of experiments, the proposed robot is competent to pass through curved pipes and vertical straight pipes. The results prove that the proposed mechanism and parameter design approach are both valid.
An In-Pipe Inspection Robot with Permanent Magnets and Omnidirectional Wheels: Design and Implementation

Kaned Thung-Od,Kiattisin Kanjanawanishkul,Thavida Maneewarn,Thunyaseth Sethaput,Arsit Boonyaprapasorn

DOI: https://doi.org/10.3390/app12031226

2022-01-25

Applied Sciences

Abstract:This paper aims to present the design and prototype of an inspection robot that can perform both horizontal and vertical locomotion in ferromagnetic pipelines. The proposed robot applies to a range from 5-inch (127 mm) diameter pipes to flat plates. The train-like robot is mainly composed of three sealed modules with omnidirectional driving wheels for longitudinal and transverse movements. Permanent magnets were designed to provide sufficient magnetic adhesion between the robot and the ferromagnetic surface of the pipes. The internal condition of the pipe can be monitored visually through cameras and sensors. Specific experimental conditions have been carried out to validate the robot’s capabilities, including maximum speed, payload capacity, and vertical climbing distance. The experimental results also show that the robot is capable of passing through a straight pipe and elbow fitting in both upward and downward directions.
Research on a Tri-axial Differential-Drive In-Pipe Robot

Sheng-Yuan Jiang,Xudong Jiang,Jie Lu,Jianyong Li,Xiangyan Lv

DOI: https://doi.org/10.1007/978-3-540-88513-9_110

2008-01-01

Abstract:Pipelines for oil, gas and fluid transportation require a robot to have an excellent mobility and adaptability to various pipelines with elbows. In this paper, a novel differential drive in-pipe robot called tri-axial differential drive in-pipe robot, which is composed of a tri-axial differential mechanism and a pipeline adaptation mechanism, is presented and developed for the inspection of pipelines with inner diameter from 275 to 300 mm. The tri-axial differential mechanism with 3-DOF for steering allows the robot easily adapt to the existing configuration of pipelines by providing outstanding mobility during navigation. Then differential and mechanics property of the robot in straight pipeline and elbow are analyzed based on established mathematical model, and multi-body simulation on the robot is conducted to confirm the effectiveness of the proposed model.
Active Screw-Driven In-Pipe Robot for Inspection

Peng Li,Wei Yang,Xin Jiang,Congyi Lyu

DOI: https://doi.org/10.1109/icus.2017.8278416

2017-01-01

Abstract:A novel active screw-driven in-pipe robot to inspect the condition of pipeline is proposed in this paper. The in-pipe robot consists of three parts, a suspension mechanism, four driving units and four electromagnetic brakes. Each driving unit includes a DC motor and a gear transmission train structure and the electromagnetic brake is used to switch the power transmission routine. Therefore, the DC motors can drive the wheels and also can steer the wheels with the help of the electromagnetic brake. Since the wheels have rolling motion and steering motion, the robot has translation motion, rotation and screw motion with respect to the axis of the pipe due to different position of the wheel steering angle. The robot can also overcome obstacles by using the screw motion mode and the compensation of the suspension mechanism. Furthermore, the relationship between the translation and rotation of the robot is investigated, simulation results shows that the steering angle can be treated as a regulator to adjust the moving speed of the robot besides its tuning the posture of the robot. Due the special moving principle, the robot can adapt circular and square tube without any change of the structure.
Design and locomotion control strategy for a steerable in-pipe robot

Te Li,Shugen Ma,Bin Li,Minghui Wang,Yuechao Wang

DOI: https://doi.org/10.1109/icma.2015.7237661

2015-01-01

Abstract:A steerable in-pipe robot based on screw drive is proposed for curved pipes and T-pipes. The robot with only two motors is composed of the drive mechanism and steering mechanism. The design principles of the robot are analyzed based on the kinematic and statics models. The spring parameters of the elastic arms are selected in consideration of the stability of steering motion. Then the steering locomotion control strategy in curved and T-pipes is given based on a simplified planar connecting rod model. In order to select a proper posture to turn, a posture adjustment strategy making full use of the pipe constraint is also proposed. The simulation results show that the proposed robot can pass through the curved pipes and T-pipes, and adjust the posture by the proposed control strategies.
Design and Control of In-Pipe Inspection Robot for Pre-commissioning

Hui Li,Ruiqin Li,Yuan Wang

DOI: https://doi.org/10.1007/978-3-030-89092-6_6

2021-01-01

Abstract:This paper presents the design, control, and implementation of a new in-pipe inspection robot named LH-6. This robot can spontaneously adapt its configuration while it is rolling in the pipeline. The constant contact of all wheels with the ground is ensured by a series of elastic spring in the middle of each supporting arm. By analyzing the wheel kinematics model of the supporting arms mechanism of rolling, the dynamic equation for the contact drive of the in-pipe robot is established, and according to the requirements of pre-commissioning condition, optimization of its control inputs is performed using optimal control approach. It provides speed and force control that allows the robot to properly balance its posture while the load can be distributed as evenly as possible on each contact wheel on the bottom of the robot for any situation of the pipeline. Finally, the robot is tested on different pipeline shapes in the field and proves its capability to adapt in real-time to the pre-commissioning pipeline.
Design and Development of Miniature long distance multi-moving robots for 3D Smart Sensing for underground Pipe Inspection

Alireza Pulles,Weiyao Lai,Erika Sahari,XiaoQi Guo,Marc Bernhard

DOI: https://doi.org/10.48550/arXiv.2208.10439

2022-08-23

Abstract:Designing an in-pipe climbing robot that manipulates sharp gears to study complex line relationships. Traditional rolling/happening pipe climbing robots tend to slide when exploring pipe curves. The proposed gearbox connects to the farthest ground plane of a standard dual output gearbox. Instrumentation helps achieve a very well-defined deceleration sequence in which the robot slides and pulls as it moves forward. This instrument takes into account the forces exerted on each track within the line relationship and intentionally modifies the robot's track speed, unlocking the key to fine-tuning. This makes the 3 output transmissions take a lot of time. Deflection of the robot on a pipe network with various bearings and non-slip pipe bends demonstrates the integrity of the proposed structure.

Robotics

In-Pipe Detection of Three-Dimensional Curving Mini-Pipe

Photoelectric Detection and 3D Reconstruction System for the Inner Surface of Small-Diameter Pipes

3D Reconstruction of Small-diameter Pipes Inner Surface Based on Structural Light

Noncontact Laser Inspection Based on a PSD for the Inner Surface of Minidiameter Pipes.

New Inner Surface Profile Sensor for Mini-Diameter Pipes

Non-Contact Inspection for Inner Surface of Small-Diameter Pipes Based on Laser-Psd

Local Geometric Measurement for 3-D Curved Micro-Pipe

Application Research of Three-Dimensional Technology Aided Design of New Pipe Inserting into Underground Pipe

Panoramic Optical Annular Staring Inspection System for Evaluating the Inner Surface of a Pipe

In-pipe Positioning Micro-Robot Based on Cymbal Actuators and Optical Navigation

Development of a 3D Pipe Robot for Smart Sensing and Inspection Using 3D Printing Technology

Study on Total Distance Positioning of In-Pipe Robot -Based on Fiber Bragg Grating Curvature Spatial Sensor

A Study On The System Of The In-Pipe Robot

Design and Development of a Deformable In-Pipe Inspection Robot for Various Diameter Pipes

Development of an In-Pipe Robot with Differential Screw Angles for Curved Pipes and Vertical Straight Pipes

An In-Pipe Inspection Robot with Permanent Magnets and Omnidirectional Wheels: Design and Implementation

Research on a Tri-axial Differential-Drive In-Pipe Robot

Active Screw-Driven In-Pipe Robot for Inspection

Design and locomotion control strategy for a steerable in-pipe robot

Design and Control of In-Pipe Inspection Robot for Pre-commissioning

Design and Development of Miniature long distance multi-moving robots for 3D Smart Sensing for underground Pipe Inspection