Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effect of Bentonite of High Specific Heat on Properties of Polymer Matrix Friction Materials

Experimental Study on Thermal Conductivity of Mixed Materials of Sand and Bentonite

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

The behavior of polymer-bentonite interface under shear stress

Effect of Bentonite Content and Hydration Time on Mechanical Properties of Sand–Bentonite Mixture

Wet Grinding of Montmorillonite and Its Effect on the Properties of Mesoporous Montmorillonite

Effects of water content on shear properties of bentonite–polymer composite structure

Effect of Synthetic Quadripolymer on Rheological and Filtration Properties of Bentonite-Free Drilling Fluid at High Temperature

Friction and Wear Property of Nano-montmorillonite Modiifed PF Reinforced Composite Material

Improving the rheological properties of water-based calcium bentonite drilling fluids using water-soluble polymers in high temperature applications

Temperature effect on mechanical strength and frictional properties of polytetrafluoroethylene‐based core‐shell nanocomposites

Improved Tribological Properties of Poly(methyl methacrylate) Based Composites by the Synergistic Effect of Incorporating Ultra-High Molecular Weight Polyethylene and Heat Treatment

Influence of Bentonite Dosage on Strength of Porous Ceramic with Quartz Sand

Thermoresponsive Bentonite for Water-Based Drilling Fluids

Effects of Vermiculite on the Tribological Behavior of Pi-Matrix Friction Materials

Effect of the Thermal Conductivity of Mated Materials on the Wear Intensity of a Polymerpolymer Friction Pair

Influence of Calcination and Cation Exchange (APTES) of Bentonite-Modified Reinforced Basalt/Epoxy Multiscale Composites' Mechanical and Wear Performance: A Comparative Study

The Effect of Powder and Emulsion Binders on the Tribological Properties of Particulate Filled Glass Fiber Reinforced Polymer Composites

Study on Preparation of Polymer-Modified Bentonite and Sand Mixtures Based on Osmotic Pressure Principle

Characterization and Tribological Performance of Polyethersulfone/PTFE Compound Filled with Na-Montmorillonite

Preparation and Tribological Behaviors of Antigorite and Wollastonite Mineral Dual-Phase-Reinforced Polytetrafluoroethylene Matrix Composites