Abstract:Micro TiB and nano La2O3 particles hybrid reinforced difficult-to-deformation Ti-6Al-4V titanium matrix composites (TMCs) were processed by severe plastic deformation of equal-channel angular pressing (ECAP). The effect of ECAP temperature on microstructure, formation mechanism of ultrafine grains and mechanical properties was studied by SEM, TEM and room temperature tensile test. The results show that ultrafine-grained (UFG) structure forms in ECAPed matrix, and ECAP temperature has significant impact on the formation mechanism. Plenty of dislocation pile-ups and tangling contribute to cell structures of hundreds of nanometers in matrix at lower ECAP temperature, while dynamic recrystallization occurs at higher ECAP temperature, which promotes the formation of a large number of new ultrafine grains (100 similar to 500 nm). The ultimate tensile strength of ECAPed TMCs at 800 degrees C is up to 1128.01 MPa, which is 18% higher than that of unECAPed ones. In addition, micro-nano reinforcements induce continuous dynamic recrystallization in the interface microdomain, resulting in further refined grains. However, the average aspect ratio of ECAPed TiB whiskers decreases with the increase of ECAP temperature, which makes TiB tend to debond with matrix and be disabled to play a load-bearing role. It results in the inapparent effect of ECAP temperature on ultimate tensile strength. And the voids in matrix formed by debonding induce stress concentration, cause crack easily and reduce ductility of TMCs.

INFLUENCE OF ECAP TEMPERATURE ON THE MECHANICAL PROPERTIES OF PURE TI

Effect of Temperature on Microstructure and Mechanical Properties of ECAPed (tib + La2O3)/Ti-6Al-4V Composites

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF TiB + TiC REINFORCED TITANIUM ALLOY BY ECAP

Evolution of microstructure, macrotexture and mechanical properties of high strength biomedical TA4 pure titanium during multi-pass ECAP

Effect of ECAP numbers on microstructure and properties of titanium matrix composite

Effect of Post-ECAP Annealing on the Microstructure and Mechanical Properties of Commercially Pure Titanium

Microstructural Evolution and Properties of Particle Reinforced Titanium Matrix Composites Processed by Severe Plastic Deformation

Residual stress, fatigue behavior, and mechanical properties of equal-channel angular pressed commercial pure titanium

Microstructure Characteristics of ECAP-processed (tib + La2O3)/Ti-6Al-4V Composites

Preparation of UFG-Ti by ECAP at the Normal Temperature and Research of Mechanical Properties

The Effect of Severe Plastic Deformation on the Microstructure and Mechanical Properties of (tib+tic) Reinforced Titanium Matrix Composites

Strain Uniformity Footprint on Mechanical Performance and Erosion-Corrosion Behavior of Equal Channel Angular Pressed Pure Titanium

Effect of Equal-Channel Angular Pressing on the Microstructure and Superelastic Behavior of Ti-25 At. % Nb Shape Memory Alloy

Microstructures and electrochemical corrosion properties of commercially pure titanium processed by multi-pass equal channel angular extrusion

Mechanical And Microstructure Evaluation Of In-Situ Titanium Matrix Composite Processed By Severe Plastic Deformation

Effect of Solution-ECAP-Aging Treatment on the Microstructure and Properties of TB8 Titanium Alloy

Ultrafine Processing of (tib+tic)/tc18 Composites Processed by ECAP Via Bc Route

Microstructure Evolution and Mechanical Properties of a Ti–35Nb–3Zr–2Ta Biomedical Alloy Processed by Equal Channel Angular Pressing (ECAP)

Microstructure evolution and mechanical properties of TiB2/Cu composites processed by equal channel angular pressing at elevated temperature

Properties of Commercial Pure Titanium under Self-Heating and High-Pressure Heating Treatment

3D FEM Simulation of Multipass ECAP Ti-50.8%Ni at Various Temperatures