Abstract:With the increasing demand of the electricity, an efficiency improvement and thereby a reduced CO2 emission of the coal-fired plants are expected in order to reach the goal of the Kyoto protocol. In the medium term, increase of thermal efficiency of the steam cycle can be achieved by a rise of the process parameters. Currently, live steam pressures and temperatures up to 300 bar and 923 K are planned as a next step. This means an increase of 50-100 K in comparison to plants presently under operation. Such a large increase will only be possible, if all thermally high loaded components of the plant are made of new materials and/or new technologies for cooling and thermal insulation are applied.Closed circuit steam cooling of blades and vanes in modern steam turbines is a promising technology in order to establish elevated live steam temperatures in future steam turbine cycles. Due to the cooling of the components, materials can be used, which are common in todays application. In this paper, a steam-cooled test vane in a cascade with external hot steam flow is analysed numerically by applying a Conjugate Calculation Technique. The boundary conditions of the hot steam are derived from the planned inlet parameter of the HP steam turbine in a medium term and a long term in order to show the application potential of such a cooling technique. The supply steam parameters of the cooling are set equal to those of the outlet steam from the HP steam turbine.The results show that the steam cooling technique can reach necessary cooling effectiveness in the steam turbine by using only minor amounts of cooling steam. The internal pan of the vane is cooled homogeneously in both investigated cases. Basic features and phenomena of the steam cooling technique in steam turbines are discussed in the paper with respect to future application. It has been found that the trailing edge region of the steam-cooled vane is less critical with respect to high thermal load than in gas turbine application with the same configuration. At the leading edge of the vane, high thermal load can be detected because of the direct impingement of the hot steam. Improvement of the leading edge cooling is recommended by increasing cooling steam amount for the leading edge channel. Thus, a larger diameter of the channel can increase internal cooling efficiency for the leading edge. Due to the different heat transfer characteristics on the suction side and pressure side, the suction side shows also a higher temperature distribution in the investigated cases.

Cooling performance contrast analysis of turbine vane by air and steam coolant

Experimental Study on Comparison of Cooling Effectiveness Between Steam and Air for a Gas Turbine Nozzle Guide Vane

Comparative Experiment of Cooling Performance in a Turbine Blade Cooled by Steam and Air Flow

Cooling performance analysis of steam cooled gas turbine nozzle guide vane

An Experimental Research on the Cooling Performance of the Turbine Vane with an Advanced Duplex-Medium Combined Cooling

Numerical Investigation On The Cooling Effectiveness Among Air And Steam And Mist/Steam For A Gas Turbine Vane

Cooling Performance Of The Steam-Cooled Vane In A Steam Turbine Cascade

Experimental study on cooling performance of a steam-cooled turbine blade with five internal cooling smooth channels

Numerical Investigation Of Heat Transfer And Flow Characteristics In A Steam-Cooled Square Ribbed Duct

Numerical Study on Flow and Heat Transfer of a Cooled First Stage Vane of a Gas Turbine

Investigation of the Steam-Cooled Blade in a Steam Turbine Cascade

Heat Transfer Comparison Investigation of Mist/steam Two-Phase Flow and Steam in a Square Smooth Channel

Comparative Study Of Impinging Jet Array Heat Transfer On A Flat Plate Cooled By Superheated Steam And Air

Numerical Study on Cooling Performance of a Steam-Cooled Blade Based on Response Surface Method

Flow and Heat Transfer Characteristics in Middle Pressure Turbine Stage in Supercritical Steam Turbines

Conjugate Heat Transfer Analysis of a High Pressure Turbine Vane with Radial Internal Cooling Passages

Flow and Heat Transfer Characteristics in Rotating Two-pass Channels Cooled by Superheated Steam

Numerical Investigations on the Steam Cooling Performance of the First Two Middle Pressure Turbine Stages for Ultra-Supercritical Steam Turbines

An Experimental Investigation of Heat Transfer Characteristics in a Steam-Cooled Square Channel with Rib Turbulators

Experimental investigation on the combined cooling methods of jet impingement and film cooling for the pressure surface of the turbine vane leading cavity

Effect of cooling on the aerodynamic performance in the intercooled compressor vanes