Abstract:The downsized boosted direct-injection spark-ignition (DISI) has become one of the most promising technique to improve engine fuel economy. However, the geometric compression ratio of downsized boosted engines is often lower than that of naturally aspirated engines because of the higher knocking tendency resulted from high boosting ratio, which deteriorates the fuel economy of boosted DISI engines. It has been proved that Miller cycle has the potential to decrease the effective compression ratio, which can ease or solve the knocking issue. In this paper, the effects of VVT coupled Miller cycle strategies on thermal efficiency was investigated on a 2.0 L boosted DISI engine over a wide range of engine operating conditions. Miller cycle strategies are realized by two different camshaft structures, which are late intake valve closing (LIVC) and early intake valve closing (EIVC) camshafts. A large map of engine experiments were conducted, in which the engine speed spans 1000 rpm to 2500 rpm with the load ranging from low to high. Comparing different Miller cycle strategies with the reference case (using base camshaft), it was found that an up to 9.56% reduction of fuel consumption was achieved. Also, experimental results show that, at high load, the fuel consumption decreased with the delay of intake valve opening (IVO) under LIVC; whereas that under EIVC first declines and then increases. At part load, brake specific fuel consumption (BSFC) for EIVC monotonically decreases as the retard of IVO; while BSFC for LIVC rises first and then decreases. In order to fully understand the mechanism of fuel consumption, contributing factors to thermal efficiency were quantified under both part load and high load conditions. It was found that the degree of constant volume heat release and mechanical efficiency are the first order of importance to thermal efficiency for both LIVC and EIVC under high and part loads, respectively, despite of the different trend of IVO effects.

Influences of Engine LIVC on Fuel Economy and Soot Emission

The Miller Cycle Effects on Improvement of Fuel Economy in a Highly Boosted, High Compression Ratio, Direct-Injection Gasoline Engine: EIVC Vs. LIVC

Numerical Analysis of the Fuel Economy and Dynamic Performance of a GDI Engine Using EGR Coupled High Expansion Ratio Cycle

Quantitative Analysis of the Influence Saliency of VVA and EGR on the Fuel Economy and Mixture Combustion Characteristics of a Turbocharged Spark Ignition Engine

Experimental Research on Knock Suppression of Turbocharged DI Gasoline Engine Based on LIVC and Dual-VVT Technology

Soot emission reduction using cooled EGR for a boosted spark-ignition direct-injection (SIDI) engine

Experimental study on combustion and emission characteristics of LIVC Miller cycle with asynchronous intake valves

Anatomy of the Cooled Egr Effects on Soot Emission Reduction in Boosted Spark-Ignited Direct-Injection Engines

Numerical Investigation of the Influence of Intake Valve Lift Profile on A Diesel Premixed Charge Compression Ignition Engine with A Variable Valve Actuation System at Moderate Loads and Speeds

Impacts of VVT Coupled Miller Cycle Strategies (LIVC and EIVC) on Thermal Efficiency in a Boosted DISI Engine

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Numerical Investigation of the Effect of Late Intake Valve Closing on Diesel HCCI Combustion and Emissions

Full Engine Cycle CFD Investigation of Effects of Variable Intake Valve Closing on Diesel PCCI Combustion and Emissions

Influence of Valve Overlap Angle on GDI Engine Performance and Particulate Emission

Multi-objective Optimization of the Combustion of a Heavy-Duty Diesel Engine with Low Temperature Combustion (LTC) under a Wide Load Range: (II) Detailed Parametric, Energy, and Exergy Analysis

Research on the Potential of Exhaust Variable Valve Lift Coupled with Ignition Timing Strategy on Improvement Energy Saving and Reduce Emissions of Methanol Engine

Study on improvement of fuel economy and reduction in emissions for stoichiometric gasoline engines

Improving the Partial-Load Performance and Emission of GDI Engine by Combining Injection Strategy and Exhaust Variable Valve Timing Technology

Experimental Study on Improvement of Air-dilution Combustion Performance of Methanol Engine by Adjusting Intake Guide Flappers, Exhaust Variable Valve Timing and Split Injection

Combined effects of cooled EGR and a higher geometric compression ratio on thermal efficiency improvement of a downsized boosted spark-ignition direct-injection engine