Abstract:At partial load, traditional automotive gasoline engines have high pumping losses due to the throttling of the intake charge for load control. Variable Valve Timing (VVT) and the introduction of externally cooled EGR could reduce the pumping losses but only with a very limited effect. On the other hand, in the medium to full load range, the engine cannot utilize a high compression ratio due to limitations in knocking. A variable displacement, variable compression ratio device which utilizes an asymmetric camshaft to realize the different closure times of the two intake valves is discussed in this paper. The large-scale change in the intake valve timing leads to the large-scale change in the effective cylinder volume at the intake valve closure, which realizes a variable cylinder volume and a variable effective compression ratio. The device is utilized to reduce the pumping losses and to increase the in-cylinder thermal efficiency at the same time. Engine dyno test results indicate that, in the low to medium load range, a later closure of the intake valve could reduce the effective cylinder volume, and the intake pressure could be significantly increased, and therefore pumping losses reduced. However, the reduced effective cylinder volume due to a later intake valve closure would lead to reduction in the effective compression ratio (ECR) and a drop in in-cylinder thermal efficiency. Therefore, there is a balance point between the pumping loss reduction and the drop in in-cylinder thermal efficiency. On the other side, in the medium to full load range, when avoiding knocking becomes the major controlling factor of the combustion phasing (degree of constant-volume combustion) and the effective expansion ratio (EER), too high of an effective compression ratio would lead to significant drop in the effective expansion ratio EER and also the in-cylinder thermal efficiency. Therefore, there exists a best compromise between the ECR and EER, and the best system would be one with a moderate ECR but an EER as high as possible. The quantitative equations which include both ECR and EER in the thermal efficiency calculations captured the above observations pretty well and can be utilized to optimize for the best compromise of IVC, EVO, ECR, EER and engine performances during the concept stage and/or the calibration stage of an engine.

Experimental Research on Knock Suppression of Turbocharged DI Gasoline Engine Based on LIVC and Dual-VVT Technology

Experiment Study and Numerical Analysis of Suppressing Knock with Scavenging for Turbocharged GDI Engine

Influences of Engine LIVC on Fuel Economy and Soot Emission

Experimental study on the optimization of operating conditions for hybrid powertrain gasoline engines

Experimental Study on Suppressing Knock of Turbocharged GDI Engine with Scavenging

Numerical and Experimental Study on Knock Sources in Spark Ignition Engine with Electromagnetic Valve Train

Experimental Research on Knocking Suppression Using Stratified Stoichiometric Mixture in a GDI Engine

Super-knock Suppression for Highly Turbocharged Gasoline Engines Using Lean Mixture Control Strategy with the Same Energy Density

Experiment and Simulation Research on Super-Knock Suppression for Highly Turbocharged Gasoline Engines Using the Fuel of Methane

Suppression of Super-Knock in TC-GDI Engine Using Two-Stage Injection in Intake Stroke (TSII)

Quantitative Analysis of the Influence Saliency of VVA and EGR on the Fuel Economy and Mixture Combustion Characteristics of a Turbocharged Spark Ignition Engine

Simulation Research on the Effect of Cooled EGR, Supercharging and Compression Ratio on Downsized SI Engine Knock

The Miller Cycle Effects on Improvement of Fuel Economy in a Highly Boosted, High Compression Ratio, Direct-Injection Gasoline Engine: EIVC Vs. LIVC

Experimental study of knock combustion and direct injection on knock suppression in a high compression ratio methanol engine

Progressive strategies to avoid and exploit knock limit for optimal performance and stoichiometric operation of a DI hydrogen engine with high CR at WOT conditions

Effect of a novel mechanical CVVL system on economic performance of a turbocharged spark-ignition engine fuelled with gasoline and ethanol blend

Experimental and Numerical Investigation on Knock for a Heavy-Duty Spark Ignition Methanol Engine

Development and Validation of a Variable Displacement Variable Compression Ratio Miller Cycle Technology on an Automotive Gasoline Engine

Optimization of Piston Bowl and Valve System in Compression Ignition Engine Fueled with Gasoline/diesel/polyoxymethylene Dimethyl Ethers for High Efficiency

Impacts of VVT Coupled Miller Cycle Strategies (LIVC and EIVC) on Thermal Efficiency in a Boosted DISI Engine

Knocking suppression by stratified stoichiometric mixture with two-zone homogeneity in a DISI engine