Abstract:In recent years, oxy-fuel combustion in coal-fired plants has become one of the most promising technologies for carbon capture and storage (CCS). Compared with air-fired combustion, high concentrations of CO2 and H2O in the flue gas cause a remarkable change in the pulverized coal combustion and heat transfer characteristics in furnace. In this study, improved models for the gas radiative properties and chemical reaction mechanisms were incorporated into the computational fluid dynamics (CFD) code to simulate a 200 MWe tangentially fired utility boiler, which is expected to operate at full load under both conventional air-fired and oxy-fuel combustion. Different flue gas recycle patterns: dry recycle and wet recycle, were also investigated. The results indicate that, stable combustion is achieved by a compatible burner design in both air-fired and oxy-fuel combustion. In the oxy-fuel combustion, the flue gas peak temperature and wall heat flux decrease and high CO concentration appears in the burner region, resulted from higher heat capacity of CO2 and chemical effect of CO2 (Liu et al., 2003, Glarborg and Bentzen, 2008). Based on the comparison of the wet recycle and dry recycle, it shows the wet recycle has more advantages than dry recycle. This study indicates a slight increase in total heat transfer, when the oxygen concentration in oxidant increases from 23% to 29%, consistent with the results of Vattenfall and Callide pilot scale oxy-combustion plant. Thus, compared with air-fired combustion, the full load of a boiler may decrease by 5-10% under oxy-fuel combustion. (C) 2014 Elsevier Ltd. All rights reserved.

Numerical Simulation of Combustion and Pollution in a 330MW Opposed Firing Boiler

Numerical Investigation on Oxy-Combustion Characteristics of a 200 MWe Tangentially Fired Boiler

Study on coal combustion characteristics in a 350MW supercritical tangentially boiler

Numerical Simulation of the Combustion and Pollution Emissions from a 75/th Circulation Fluidized Bed Boiler of Power Plant

Numerical Simulation of the Flow and Combustion Processes in a Three-Dimensional, W-Shaped Boiler Furnace

Numerical Simulation Of The Combustion Processes In A W-Shaped Boiler Furnace Under Different Operating Conditions

Numerical Simulation of O2／CO2 Recycled Flue Gas Combustion in a 300 MW Boiler

Numerical Simulation of Combustion Process for an 1000MW Ultra-Supercritical Boiler at Different Air Distribution Proportions

Numerical Investigation of Different Burner Arrangement on A Coal-Fired Boiler

Numerical and experimental investigation on the reduction of NOx emission in a 600 MW utility furnace by using OFA

Numerical Simulation of Combustion in 35 t/h Industrial Pulverized Coal Furnace with Burners Arranged on Front Wall

Numerical Simulations On The Effect Of Over-Fire Air To The Combustion Performance In A 2950 T/H Tangential-Fired Boiler

Prediction on pulverized coal combustion process in the boiler using computer simulation

E305 NUMERICAL SIMULATIONS ON THE EFFECT OF OVER-FIRE AIR TO THE COMBUSTION PERFORMANCE IN A 2950 T/H TANGENTIAL-FIRED BOILER(Boiler-1)

Numerical and experimental investigations on the performance of a 300 MW pulverized coal furnace

Numerical Simulation of Combustion Process for a Slag Tapping Boiler

Numerical simulation on effects of over fire air on the combustion characteristics in an ultra-supercritical boiler

STUDY ON NUMERICAL SIMULATION OF DECREASING NOx EMISSION FROM COAL-FIRED BOILERS BASED ON BFA AND OFA

Numerical simulation of the two-phase flow and combustion in the tangential-firing boiler furnace by using the ALE algorithm and trajectory model

Experimental Research and Numerical Simulation on Combusting CWS in 410t/h Six-corner Tangentially Firing Boiler

Modeling of Coal Combustion and NOx Formation in a W-shaped Boiler Furnace