Abstract:The Molten Salt Reactor (MSR) is one of the six Generation IV systems capable of breeding and transmutation of actinides and long-lived fission products, which uses the liquid molten salt as the fuel solvent, coolant and heat generation simultaneously. The MSR neutronics, such as the distribution of the delay neutron precursors (DNP), is significantly influenced by the fluid flow, which is quite different from the conventional reactors. Therefore, it is very important to do some research on MSR, especially in accident conditions. The present paper studies the natural convection through which the heat generated by the fuel is removed out of the core region (simply a square cavity in this paper).The neutronic theoretical model is founded based on the conservation law, which consists of two-group neutron diffusion equation for the fast and thermal neutron fluxes and that for one-group DNP, in which the convection terms are included to reflect the fuel salt flow. The SIMPLER numerical method was used to calculate the natural convection heat transfer to the molten salt inside a closed cavity for which the boundary temperature was spatially uniform. The equations were discretized by finite volume method based on collocated grids, in which QUICK defect correction was adopted for the convection terms and the central difference was for the diffusion terms. The discretization equations were calculated by ADI (Alternative Direction Implicit) with block-correction technique.The distributions of the dimensionless temperature, the dimensionless velocity, the fluxes and the DNP in the cavity were obtained. The calculated results showed that: a) the distribution of the DNP was correlated both with that of the fluxes and with the fuel salt flow and when Rayleigh number increased, the latter one was of much more importance; b) the distribution of the local Nusselt number varied with different Rayleigh numbers; c) the distribution of the dimensionless velocity and the dimensionless temperature were also closely related to Rayleigh number; d) the maximum dimensionless temperature decreased as Rayleigh number increases.

Temperature field analysis for the main shielding of the 2-MW thorium-based molten salt experimental reactor

Preliminary Neutronic and Thermal-Hydraulic Analysis of a 2 MW Thorium-based Molten Salt Reactor with Solid Fuel

Radiation dose distribution of liquid fueled thorium molten salt reactor

Steady Thermal Hydraulic Analysis for a Molten Salt Reactor

Three-dimensional thermal hydraulic analysis of a transportable fluoride-salt-cooled high-temperature reactor

Transient Analysis For Liquid-Fuel Molten Salt Reactor Based On Morel2.0 Code

Thermal-hydraulic Design and Analysis of a Small Modular Molten Salt Reactor (MSR) with Solid Fuel

The Influence of Lower Plenum and Distribution Plates to Thermal Hydraulics Characteristics of MSR

Thermal-Hydraulic Analyses of Transportable Fluoride Salt–Cooled High-Temperature Reactor with CFD Modeling

Coupled Neutronic and Thermal-Hydraulic Analysis of TMSR-SF1 at Steady State

Radiation Damage Simulation and Analysis of TMSR-LF1 Functional Channel Alloy Sleeves Based on Monte Carlo Method

Core and blanket thermal–hydraulic analysis of a molten salt fast reactor based on coupling of OpenMC and OpenFOAM

Numerical Analysis for a Molten Salt Reactor in the Presence of Fissile Lump

Transient Analysis of Tritium Transport Characteristics of Thorium Molten Salt Reactor with Solid Fuel

Steady Thermal Hydraulics Analysis for A Graphite-Moderated Channel Type Molten Salt Reactor

Neutron/Gamma Radial Shielding Design of Main Vessel in a Small Modular Molten Salt Reactor

Transient Safety Analysis of A Transportable Fluoride-Salt-Cooled High-Temperature Reactor Using Relap5-3d

Thermal Hydraulics Analysis of the Fluoride-Salt-Cooled, High-Temperature Reactor

Natural Convection With Non-Uniform Heat Generation In Molten Salt Reactor

Analysis of Radioactive Effect in Molten Salt Reactor

ICONE19-43445 Investigating Thermal-Hydraulic Characteristic of Molten Fluoride Salt in A Circular Pipe Using A CFD Methodology