Abstract:China is accelerating the development of sodium-cooled fast reactor technology.For nuclear reactors,whether it is a pressurized water reactor or a fast reactor,core flow distribution is a key concern,which directly determines whether the reactor can operate safely and reliably.Sodium-cooled fast reactor core adopts a three-stage flow distribution method consisting of diagrid,distribution headers and assemblies.Distribution headers are installed on diagrid,and various types of assemblies are installed on distribution headers.Pressure drop of the core is composed of distribution header pressure drop and assembly pressure drop.The distribution header pressure drop itself affects the flow distribution of the assemblies,thereby affecting the safety of the core.Therefore,it is of great significance to study the impact of distribution header pressure drop on the flow distribution of assemblies for the sodium-cooled fast reactors.In order to reduce the flow distribution deviation of assemblies caused by the distribution header pressure drop,it is necessary to carry out a reasonable assembly pressure drop design.Based on the mechanism of flow distribution deviation of assemblies caused by distribution header pressure drop,a theoretical calculation model was proposed,and an optimized design of assembly pressure drop was carried out for the China Experimental Fast Reactor(CEFR)core.Based on the actual layout of CEFR core,the maximum deviation of flow distribution of fuel assemblies was obtained,and the optimization direction of nominal assembly pressure drop was determined,indicating that optimization design of nominal assembly pressure drop should be carried out for the first five rings.After adjusting the nominal pressure drop of the first five rings of assemblies from 250 kPa(the original nominal pressure drop)to 249 kPa,248.5 kPa,and 248 kPa,respectively,the maximum deviation of flow distribution of fuel assemblies firstly decreases from-0.99％to-0.95％,and then increases to-1.02％and-1.08％,which indicates that nominal assembly pressure drop should be elaborately determined to obtain a minimum flow distribution deviation of fuel assemblies.In conclusion,when conducting core thermal hydraulic design for sodium-cooled fast reactors,it is necessary to analyze the optimization direction of nominal assembly pressure drop based on actual core layout,and sensitivity analysis should be conducted to finally determine the nominal assembly pressure drop to reduce the impact of distribution header pressure drop on flow distribution of assemblies to the lowest extent.

Impact of CEFR Core Assembly Installation on Flow Rate Distribution among Core Assemblies

Steady-state Simulation of Core-Annulus Flow in a Circulating Fluidized Bed (CFB) Riser

Effect of Distribution Header Pressure Drop on Flow Distribution of Assembly for Sodium-cooled Fast Reactor

Numerical Simulation of Compact Fuel Assembly in Fast Reactor

Frequency Measurement Test on Fuel Assembly of China Experimental Fast Reactor

Numerical investigation on the core thermal hydraulic behavior of pool-type sodium-cooled fast reactor (SFR)

CFD Investigation of Thermal-Hydraulic Behaviors in Full Reactor Core for Sodium-Cooled Fast Reactor

CFD Simulation of a 61-pin Wire-wrapped Fuel Subassembly for Sodium Cooled Fast Reactor

Flow Distribution in a Pool Type Nuclear Reactor Core with Planar Fuel Assemblies

Research of Calculation Method of Assembly Equivalence with Boundary Flow Response Matrix

Development a Methodology for Evaluating Inter‐assembly Heat Transfer Effect Through Reactor Core in System Safety Analysis of Sodium‐cooled Fast Reactor

NUMERICAL AND EXPERIMENTAL INVESTIGATION ON CORE ASSEMBLY THERMAL-GRADIENT-INDUCED DEFORMATION OF SODIUM-COOLED FAST REACTOR

High Fidelity Core Flow Measurement Experiment for an Advanced Research Reactor Using a Real Scale Mockup

Numerical Simulation and Analysis on Thermal-hydraulic Behavior of Fuel Assembly for Sodium-cooled Fast Reactor

CFD investigation for a 7-pin wire-wrapped fuel assembly with different shapes of fuel duct wall

Coupled Neutronics and Thermal–Hydraulics Analysis of Annular Fuel Assembly for SCWR

Numerical investigation of flow blockage accident in SFR fuel assembly

Theoretical Analysis for Coupled Thermal Deformation Behaviors of Subassemblies in a Single Row in Sodium-Cooled Fast Reactors

Single-phase Flow in Helical Cruciform Fuel Assembly with Conjugate Heat Transfer

CFD Simulation on the Flow Characteristics in the PWR Lower Plenum with Different Internal Structures

CFD analysis for full vessel upper plenum in Maanshan Nuclear Power Plant