Research Status of HVDC XLPE Cable

WangYa,Zepeng Lv,Kai Wu,Xia Wang,Tong Liu,Ruihai Li

DOI: https://doi.org/10.3969/j.issn.1009-9239.2014.01.006

2014-01-01

Abstract:The international application of high voltage direct current(HVDC) transmission cable was pre-sented. The research situation of space charge and test methods of the HVDC cable was summarized, and the development direction of the HVDC cable materials and test methods were prospected.

What problem does this paper attempt to address?

Investigation on Dielectric Insulation Properties of ±525 Kv HVDC XLPE Material for High Temperatures Applications

Ziwei Zhao,Muhammad Awais,Yuantao Zhao,Qi Tang,Feng Xia,Xiangrong Chen

DOI: https://doi.org/10.1109/hvdc62448.2024.10723025

2024-01-01

Abstract:With the increasing demand of long-length and large-capacity power transmission around the world, the $\pm 525$ kV high voltage direct current (HVDC) Cross-Linked Polyethylene (XLPE) cable system has been widely recognized as the potential technology for power transmission. To further enhance the HVDC cable transmission capacity at a more economical level, the high conductor operation temperature is indispensable. However, higher temperature is more dangerous for XLPE cable insulation especially under HVDC stress. Therefore, it is recommended by Cigre TB 852 [1] that the high temperature performance of insulation material should be examined. Various dielectric insulation tests at different temperatures are performed on sliced XLPE samples from real HVDC cable. The testing results are carefully analyzed and can provide guidance for the efficient design of insulation system for high temperature $\pm 525\text{kV}$ HVDC cable system applications.
Analysis of Thermo-electric Coupled Simulation for 10 Kv AC XLPE Cable under Different DC Topologies and Laying Modes

Yicheng Mao,Qilong Wang,Jingzhe Yu,Ashish Paramane,Guangyuan Yao,Xiangrong Chen

DOI: https://doi.org/10.1109/aeero52475.2021.9708110

2021-01-01

Abstract:This research aims to provide a theoretical reference for the 10 kV AC cable under the DC operation. To study the DC operation parameters of the AC cable in different laying methods and DC topologies, the temperature field, flow field, and electric field coupled simulation models are developed according to the parameters of the typical 10 kV three-core XLPE cable. The temperature field, flow field, steady electric field, and transient electric field of the cable under DC operation are obtained by simulation. The cable-laying methods consisting of soil, pipeline, and trench under the bipole, monopole, and triple DC topologies are analyzed. The results show that the cable in the trench and tripole DC operation has the highest ampacity, while the cable in the pipeline and monopole DC operation has the lowest ampacity. The range of the DC voltage levels of the cable in the aforementioned laying modes and DC topologies is ±10~11 kV. The maximum transmission power of the cable in the trench and monopole DC operation is the highest, while that of the cable in the pipeline and bipole DC operation is the lowest. The maximum transmission power of the AC cable significantly increases under DC operation.
Development of High Voltage Direct Current Extruded Cables

ZHONG Lisheng,REN Haiyang,CAO Liang,ZHAO Wei,GAO Jinghui

DOI: https://doi.org/10.13336/j.1003-6520.hve.20171031001

2017-01-01

Abstract:High voltage direct current (HVDC) extruded cable is one of the key power devices for realizing the flexible interconnection of large power grids,the power transmission with long distance and large capacity,and large-scale utilization of renewable energy.We review the progress of HVDC extruded cables from aspects including the development of insulating materials,accessory technologies,testing methodologies,cable measuring and detecting techniques as well as main projects worldwide.In particular,we analyze recent studies on DC conductivity and space charge properties of various insulation materials for DC cables,type and prequalification tests of DC cable systems as well as measurement methods of space charge and DC partial discharge on full-size cables.Moreover,we put forward urgent questions need to be solved in HVDC extruded cable technology,for instance,studying DC conductivity and space charge characteristics as well as long-term aging behavior and mechanism of existing insulation,developing new materials for higher voltage DC cables and accessories,optimizing the structural design of cable accessories,improving the space charge measurement and DC partial discharge detection technologies for full-size cables,and revising corresponding standards and regulations for HVDC extruded cable systems.Hopefully,the research will provide a reference for designing,manufacturing,testing,operating,and maintaining of HVDC extruded cables in China.
Study on Space Charge Characteristic of New XLPE Insulation Material for HVDC Cable

Xi Chen,Kai Wu

DOI: https://doi.org/10.3969/j.issn.1009-9239.2015.05.009

2015-01-01

Abstract:The temperature gradient effect during operation of HVDC cables will lead to field distortion greatly of the outer insulation layer, which would lead to the electric strength and lifetime of cable insu-lation decrease. Based on the polyethylene nanocomposites, a new HVDC cable insulation material was prepared by adding crosslinking agent and antioxygen, and its mechanical properties and electrical proper-ties were tested, and then its space charge accumulation and field distortion characteristic were compared with foreign XLPE HVDC cable insulation material. The results show that the properties of the new HVDC cable insulation material are superior to the foreign cable material, and the new HVDC cable insu-lation material is expected to be used in the production of HVDC cables.
Development and Outlook of Insulating Materials for High Voltage Direct Current Cables

张翀,查俊伟,王思蛟,巫运辉,闫轰达,李维康,陈新,党智敏

DOI: https://doi.org/10.16790/j.cnki.1009-9239.im.2016.02.001

2016-01-01

Abstract:The basic principle, application status, and technical bottlenecks of high voltage direct current (HVDC) cables were introduced according to the history of HVDC cables, and the necessity and urgency for developing HVDC cables were pionted out in China. The future development direction of HVDC cables was prospected.
Research Status of High Temperature Superconducting Power Cable

Zhe Wang,Zhining Lv,Peng Yu,Zhonghang Li,Bangzhu Wang

DOI: https://doi.org/10.1109/eebda53927.2022.9745003

2022-02-25

Abstract:High temperature superconducting (HTS) power cable has the merits of low transmission loss, massive power capacity, small site corridor, and environmental friendliness. And it has the unique ability to transmit large currents at low voltage, which makes it an alternative competitor to high voltage transmission. After about three decades, HTS power cable has moved from the laboratory to practical applications, which may reshape the traditional electrical energy transmission methods and even the power grid architecture. The paper reviews the current research status of HTS cable technology throughout the world over the past decade and representative demonstration projects are introduced. From the R&D activities we can conclude that HTS power cable can be characterized by a marked increase in maturity, more focused application scenarios, and greater reduction on system costs. Technical breakthroughs under applications such as power supply in urban area and interconnection of substations have been made. We believe that the important works ahead are to improve the long-term operational flexibility, reliability, and simplicity.
Research Progress and Path Analysis of Insulating Materials Used in HVDC Cable

LI Shengtao,WANG Shihang,LI Jianying

DOI: https://doi.org/10.13336/j.1003-6520.hve.20180430002

2018-01-01

Abstract:DC power transmission has become more and more important in power grid construction, and the HVDC cable is one of the most important power devices. However, due to long-time monopoly by foreign firms, China has no enough ability in mass production of stable and reliable HVDC cable insulating materials and shielding materials at present, thus it is urgently needed to develop new cable materials with independent intellectual property rights in our country. From the aspect of technical requirements, we review the research path and future development, research progress and path analysis of HVDC cable materials. Firstly, we discuss the technical requirements including dielectric strength, electric field distribution, and space charge transport. Then, we analyze the present situation, advantages and disadvantages, trap characteristics, and the development direction of cable materials including high purity cable materials, nanocomposite cable materials, blended composite cable materials, grafting cable materials, and shielding materials. Finally, we forecast the future development. The co-relationship between DC insulation characteristics is established using the charge trap theory. The effect of charge trap behavior on DC insulation characteristics is obtained. The trap characteristics and adjusting methods for various paths are summarized. This research can provide a theoretical support for the development of new DC cable materials.
Effect of Thermal Ageing on Space Charge Behavior of HVDC XLPE Materials

Chao Dai,Linwei Yu,Chen Jiang,Xiangrong Chen,Hao Zhou,Yasuhiro Tanaka

DOI: https://doi.org/10.1109/icempe.2019.8727292

2019-01-01

Abstract:The aim of the paper is to present the influence of thermal ageing on the space charge characteristics, DC conductivities and trap energy levels of DC XLPE materials. A commercial compound for 320 kV HVDC XLPE cables was used for sample preparations. XLPE films were made by a heating press method in the laboratory. The samples were placed in a thermal oven and thermally aged at 130 □ up to 21 days. Space charges were measured by a pulsed electro-acoustic (PEA) method setup developed in the high voltage laboratory. The results showed that the reference samples had limited hetero charge accumulations near both electrodes in the samples. The homo-charge accumulation was appeared with an increase of the aged time. The electric field increased gradually with the appearance of the homo-charge accumulation in the samples. The conductivity of the sample aged for 21 day increased three orders of the magnitude from 30 °C to 60 °C. It was found that a turning point of the conductivity appeared for the aged sample at 40 °C, 50 °C and 60 °C, respectively. An increase of the trap energy density and a reduction of the trap level could facilitate the homo charge accumulation in the sample aged for 21 days. The bipolar homo-charge accumulation was elucidated as an essential characteristic in the thermally aged samples.
Analysis of Influence Factors on Space Charge Accumulation Characteristics of 320 kV XLPE Cable

Cai, Xinjing

DOI: https://doi.org/10.1134/S0965545X22700316

2022-09-22

Polymer Science Series A

Abstract:The development of high voltage direct current (HVDC) transmission technology in China has put forward higher requirements to the properties of HVDC cable, the cross-linked polyethylene (XLPE) materials have drawn extensive attention for their excellent properties, and its interface space charge accumulation as well as field distribution have become a hot topic. Aiming at revealing the transport characteristics of space charge in 320 kV XLPE cable, the bipolar charge transport model has been extended to a cylindrical configuration with several modifications, featuring charge injection, trapping, detrapping and recombination. Furthermore, by setting parameters such as trap coefficient, trap depth, injection barrier height, and mobility related to material cross-linking, cable thermal aging, and nanoparticle doping, the space charge transport characteristics are simulated. The results show that the space charge density at the electrodes is decreased by the low trapping coefficient, shallow trap depth, high injection barrier, and high mobility. Therefore, the design of cable can be guided by the selection of cross-linked materials, thermal aging resistance and doping nanoparticles.
Investigation of space charge behavior of HVDC XLPE cables using PEA method

Shuqi Li,Li Lan,Jiandong Wu,Yi Yin

DOI: https://doi.org/10.1109/ISEIM.2014.6870726

2014-01-01

Abstract:Space charge accumulation is a key factor concerning the safe operation of HVDC cables. In order to investigate space charge behavior of HVDC cross-linked polyethylene (XLPE) cables, degassed specimens as well as fresh specimens obtained from HVDC XLPE cables before and after type tests were tested by PEA measuring system. The measurement was performed under DC electric fields of 10kV/mm, 20kV/mm, 30kV/mm and 50kV/mm at room temperature with both stressing and short-circuit time of 1800s. A large quantity of hetero-charges were observed in the vicinity of the electrodes in fresh specimens while only a small quantity of hetero-charges appeared under 50kV/mm in degassed specimens. The field enhancement factors (defined as FEF) of fresh specimens were also higher than that of degassed specimens. These phenomena lead to discussions on the effect of degassing. Meanwhile, assessment is also made of the aging extent caused by type tests. It is demonstrated by data analysis that hetero-charge density is closely associated with crosslinking byproducts. Degassing can effectively reduce byproduct levels and thus reduce space charge accumulation. For specimens obtained from the central section of the cables, changes in space charge distribution before and after type tests are not distinct. Therefore, the aging extent of the central section of the cable after type tests is rather minor.
Numerical Analysis of Thermo-Electric Field for AC XLPE Cable in DC Operation Based on Conduction Current Measurement.

Xiangrong Chen,Jingzhe Yu,Linwei Yu,Hao Zhou

DOI: https://doi.org/10.1109/access.2018.2890157

IF: 3.9

2019-01-01

IEEE Access

Abstract:With rapid development of renewable energies and dc loads in distribution grids, converting ac distribution grids into dc operation has become a promising method to utmost utilize the present ac distribution grid in large cities. This paper reports a numerical investigation of thermo-electric fields of a three-core 10-kV ac cross-linked polyethylene (XLPE) cable and cable joint in the dc operation. DC conduction current for the XLPE and silicon rubber (SiR) was evaluated at different temperatures and electric fields. The thermo-electric field simulation was performed by COMSOL Multiphysics according to the measured data. The obtained result showed that the threshold of XLPE at 65 °C is 3.1 MV/m, whereas the threshold of SiR at 60 °C is 2.2 MV/m. It was found that the maximum electric field of the cable operated in dc voltage up to 12.5 kV was below the threshold of 3.1 MV/m. The maximum electric field in the cable joint appeared at the high voltage screen tube, whereas the maximum electric field at the high voltage screen tube was less than the threshold of SiR at a temperature difference of 25 °C. Moreover, the maximum transmission power of the three-core 10-kV AC XLPE cables running at the ±10-kV bipolar dc operation was 1.36 times of the power in the ac operation. It was elucidated that the three-core ac 10-kV XLPE cable could be operated reliably at ±10 kV in bipolar dc topology with sufficient safety margin. It is beneficial to upgrade the ac distribution grid to the dc distribution grid.
Thermo‐electric Field Analysis of AC XLPE Cable in Monopole, Bipole, and Tripole DC Operation Modes

Xiangrong Chen,Jingzhe Yu,Hao Zhou

DOI: https://doi.org/10.1049/iet-gtd.2019.0064

2019-01-01

IET Generation Transmission & Distribution

Abstract:This paper presents a numerical analysis of thermo-electric fields of 10 and 35 kV AC XLPE cables in monopole, and tripole DC operating modes based on conduction current measurements. DC conductivities and electric field thresholds of the space charge accumulation for XLPE materials were estimated at different temperatures and electric fields. The result showed that the electric field threshold of the space charge accumulation for the materials reduced with an increase of the temperature. DC currents of the cables were increased with the increase of the operating temperatures in the three DC operation modes. The maximum DC operation voltage of the cables increased with the decline of the operation temperature in the three DC operation modes. The maximum transient electric fields were below the threshold of the space charge accumulation for the cables in the tripole DC operation. The maximum transmission power of the 10 kV XLPE cable in the DC operation modes was at 60 degrees C, whereas the maximum transmission power of the 35 kV XLPE cable was at 50 degrees C. It was elucidated that the 10 kV AC XLPE cable could have more advantages than the 35 kV AC XLPE cable in the three DC operation modes.
Review of Field Test Methods of High Voltage Direct Current XLPE Submarine Cable

Qiang Kang,Sen Qian,Yang Xu,Shuai Hou,Mingli Fu,Ye Tian

DOI: https://doi.org/10.3969/j.issn.1009-9239.2015.08.002

2015-01-01

Abstract:With the rapid increase of installed capacity of off-shore wind power, the high voltage direct current cross-linked polyethylene(XLPE) submarine cables have got fast development in Europe and China. However, there is no international standard or technical specification concerning about the preven-tive test of submarine cable up to now. It is very necessary for the power grid company to guide the preventive tests according to standards or technical specifications. This paper reviewed the preventive test methods of HVDC submarine cables, which consisted of DC voltage withstand test, time domain reflec-tometry measurement, and some test mothods of cable accessory. Furthermore, the partial discharge charac-teristics under DC voltage were discussed. Finally, the application prospect of distributed optical fiber in monitoring temperature, stress and strain of submarine HVDC cables was introduced.
The Development of HVDC Transmission System

Zhou Yang,Zhuojiang Dao,Fenwang Yu

DOI: https://doi.org/10.1109/icdma.2012.214

2012-01-01

Abstract:The ever increasing process of high-voltage high-power fully controlled semiconductor technology has promoted the flexible ac transmission systems ahead significantly. Developments advance both the HVDC power transmission and the flexible ac transmission system technologies. In this paper, an overview of HVDC power transmission systems is provided. Recent advanced technology in this area is presented. Advantage and disadvantage of typical topologies are studied and compared. It is confirmed that HVDC transmission systems have great prospects in the future.
Polymeric insulation for high-voltage dc extruded cables: challenges and development directions

Zhonglei Li,Boxue Du

DOI: https://doi.org/10.1109/mei.2018.8507715

IF: 2.939

2018-11-01

IEEE Electrical Insulation Magazine

Abstract:High-voltage DC (HVDC) power transmission plays a key role in the global power grid today and will continue to play a key role in the future, particularly for high-voltage, large-capacity, long-distance power transmission and regional power grid interconnection [1]. HVDC was first developed in the 1930s as a reliable technology that can effectively convert AC electricity produced at the point of generation to DC electricity for transmission. In 1954 the world's first commercial HVDC project connected the Swedish mainland and the Island of Gotland with a ±100 kV mass-impregnated cable with a power rating of 20 MW [2], [3]. Since the 1960s the number of HVDC systems has grown rapidly with the maturation of thyristor and transistor technologies. Two main technologies were developed in the past half century:

engineering, electrical & electronic
Simulation and Analysis of Magnetic Field in HVDC Transmission Cable

Zhan Xiong,Ji Fang,Bo Zhang

DOI: https://doi.org/10.1088/1757-899x/382/3/032041

2018-01-01

IOP Conference Series Materials Science and Engineering

Abstract:HVDC is well known for its high efficiency and controllability, which is the first choice when it comes to long-distance, colossal-power transmission. Currently, HVDC transmission is a worldwide concerned topic, especially for Australia, where the imbalance of electricity between populated areas and remote regions is a difficulty to be solved. For instance, Basslink, a brilliant HVDC transmission achievement gave a solution to this problem. At the same time, the magnetic and electrical field produced by HVDC is totally different from traditional AC transmission, which, is a special topic worth researching. This paper will investigate the HVDC transmission cable magnetic field’s characteristics and its interaction with the nearby cables. The scope of our topic are: the analysis of the magnetic field; how the magnetic field of one cable influences others; what are the advantages and disadvantages of the interactions; the comparison between HVDC transmission and common AC transmission with the grid; use ANSYS to simulate the possible situations of the magnetic field of HVDC Transmission Cable that would happen in the real world; the human exposure to magnetic field are investigated considering different laying configurations, conductor dispositions, and supply conditions.
Simulation Analysis of Temperature Field and Electric Field for 10 kV AC XLPE Cable in DC Operation

Jingzhe YU,Yijing SU,Hao ZHOU,Liexiang HU,Xiaoming HUANG,Feng XU

DOI: https://doi.org/10.13336/j.1003-6520.hve.20171031021

2017-01-01

Abstract:After the AC cable distribution line is transformed into DC operation,the use of the original line's power supply capacity can be maximized by designing the operation parameters of the cable accurately.We established a simulation model for the temperature and the electric field coupling according to the parameters of the typical three-core XLPE cable widely used in 10 kV AC distribution network by using the finite element analysis software ANSYS.The temperature field and the transient and steady state electric field were simulated and analyzed for the cable in DC bipolar operation.The results show that,for the selected typical cable,when it lays in the 40 ℃ air and the long-term working temperature of the conductor is 70 ℃,the current carrying capacity of the cables is about 440 A.Meanwhile,in order to avoid the effect of the space charge,the DC voltage range of the selected cable is ±10～±20 kV,and its maximum transmission power is 1.3～2.6 times before reconstruction.The conclusions as well as the design conditions and procedures can provide some references for the related engineering.
Key Technical Analysis and Prospect of High Voltage and Extra-high Voltage Power Cable

周远翔,刘睿,张云霄,赵健康,陈铮铮

DOI: https://doi.org/10.13336/j.1003-6520.hve.2014.09.001

2014-01-01

Abstract:All aspects, such as the expansion of power industry, the increasing diversity of power transmission, and the needs in urban power consumption, hydropower transmission and undersea transmission, and environmental protection, lead to the increasing application of power cables in both amount and types, for instance even gas insulated pipeline(GIL) is getting close to practical application. We summarized the characteristics, development and present practical application of power cables worldwide, and made prospects about the main trends of power cable development in the future. Moreover, we discussed the main topics about power cables such as high performance dielectric material, aging of electrical tree, space charge accumulation, design of insulation structure, and operation detection. It is concluded that the application of DC cables will be an important part in power transmission, but it has to overcome some key problems such as space charge accumulation. The needs for power cables are closely related to the requirements in aspects of society, economy, and environment. A hybrid transmission line model of overhead transmission, power cable and gas insulated pipeline is adopted to solve the bottleneck of power transmission in the future due to altitude limit, sea crossing, and ecology issues. It is concluded that, due to the increases of energy demand, city scale, and working condition's complexity, a significant rise in the application scale of AC and DC power cables is expected. Power cable and GIL will become more and more important in the power industry, and the main restriction will be their reliability and economy.
Research progress of semiconductive shielding layer of HVDC cable

Yanhui Wei,Wang Han,Guochang Li,Qingquan Lei,Mingli Fu,Chuncheng Hao,Guanjun Zhang

DOI: https://doi.org/10.1049/hve.2019.0069

IF: 4.967

2020-01-20

High Voltage

Abstract:As an indispensable part of high‐voltage direct current (HVDC) cable, the semiconductive shielding layer plays the role of uniforming electric field in the cable. However, cable shielding materials >35 kV mainly rely on foreign imports in China, which belongs to the technical weak issues in the field of electrical materials. At present, there are few systematic reports on semiconductive shielding material of HVDC cable. In the work, the mechanisms of charge conduction and thermal conduction of semiconductive material have been introduced. Effect of raw material, carbon black content and the second conductive filler on the resistance characteristics of the semiconductive layer, the charge accumulation characteristics of the insulating layer and the interface characteristics have been studied. A kind of semiconductive layer as a high voltage terminal charge emission method has been proposed to study charge emission from the semiconducting layer to the insulation layer. This work can provide theoretical guidance for the research of semiconductive shielding materials.

engineering, electrical & electronic
Development and Properties of Home-Made 110 kV XLPE Cable Material

CAI Jian-chao,LIU Mei-bing,HE Jun,FENG Ben-qing,TU De-min

DOI: https://doi.org/10.3969/j.issn.1672-6901.2012.06.009

2012-01-01

Abstract:The research and development of home-made YJ-110 kV HV XLPE cable material are presented.The content covers the development of base material and the improvement of its properties,the application of late absorbability technology,the hierarchy of cross-linking,the process flow of production technology,the depuration measure,the production equipments and the impurity measuring apparatus on line.Finally,it is shown by test that the properties of YJ-110 HV XLPE cable material accord with the technique target.

Research Status of HVDC XLPE Cable

Investigation on Dielectric Insulation Properties of ±525 Kv HVDC XLPE Material for High Temperatures Applications

Analysis of Thermo-electric Coupled Simulation for 10 Kv AC XLPE Cable under Different DC Topologies and Laying Modes

Development of High Voltage Direct Current Extruded Cables

Study on Space Charge Characteristic of New XLPE Insulation Material for HVDC Cable

Development and Outlook of Insulating Materials for High Voltage Direct Current Cables

Research Status of High Temperature Superconducting Power Cable

Research Progress and Path Analysis of Insulating Materials Used in HVDC Cable

Effect of Thermal Ageing on Space Charge Behavior of HVDC XLPE Materials

Analysis of Influence Factors on Space Charge Accumulation Characteristics of 320 kV XLPE Cable

Investigation of space charge behavior of HVDC XLPE cables using PEA method

Numerical Analysis of Thermo-Electric Field for AC XLPE Cable in DC Operation Based on Conduction Current Measurement.

Thermo‐electric Field Analysis of AC XLPE Cable in Monopole, Bipole, and Tripole DC Operation Modes

Review of Field Test Methods of High Voltage Direct Current XLPE Submarine Cable

The Development of HVDC Transmission System

Polymeric insulation for high-voltage dc extruded cables: challenges and development directions

Simulation and Analysis of Magnetic Field in HVDC Transmission Cable

Simulation Analysis of Temperature Field and Electric Field for 10 kV AC XLPE Cable in DC Operation

Key Technical Analysis and Prospect of High Voltage and Extra-high Voltage Power Cable

Research progress of semiconductive shielding layer of HVDC cable

Development and Properties of Home-Made 110 kV XLPE Cable Material