Abstract:Acetic acid lignin (AAL) obtained from Bagasse was used as a partial substitute of polyols for polyurethane (PU) adhesive due to the presence of reactive sites, i.e. aliphatic and aromatic hydroxyl groups, in its structure. To improve its reactivity, lignin is partly demethylated before the copolymerization with polyisocyanate. The demethylation, catalyzed by hydrobromic acid solution under heating conditions, resulted in a decrease of methoxy groups on the phenyl ring and the increase of phenolic hydroxyl groups. It is found that 120 ℃ is the preferred temperature for the demethylation resulted in a 36.5 % increase in hydroxyl content of lignin up to 5.25 mmol/g. Lignin-based polyurethane adhesives were prepared in two steps including preparing a prepolymer based on mixtures of toluene-2,4-diisocyanate (TDI) and unmodified or demethylated lignin, and then the polymerization was completed by adding polyethylene glycol (PEG). The mass ratio (1:1) of TDI: (lignin + PEG) in the compositions was here investigated. The results indicated that the presence of lignin (with and without demethylation) in polyurethane adhesives increased the glass transition temperature, Young’s modulus, and elongation at break. Particularly, the tensile strength was increased by 15–36 MPa with the addition of 10–30 wt% of lignin. Lignin with higher amount of hydroxyl groups prepared by partly demethylation is better integrated into the three-dimensional cross-linking networks of the covalent polymer as a substitute of polyols. Compared to those PU adhesives based on the raw AAL, the adhesives prepared by demethylated lignin have higher tensile strength and thermal stability. It indicates that the demethylation is effective and it is a good strategy to prepare lignin-based PU adhesive with favorable mechanical properties.

Preparation and properties of polyurethane adhesive from liquefied rice husk polyols

The Preparation of Solvent-Free Polyurethane Laminating Adhesive with Mixed-Polyols

Preparation of Polyurethane Foam from Liquefied Rice Straw

Liquefaction of Banana Pseudo-stem and Preparation of Polyurethane Adhesive from Liquefied Products

Signally improvement of polyurethane adhesive with hydroxy-enriched lignin from bagasse

Facile synthesis of polyester-polyether block copolyols for the sustainable high-performance polyurethane reactive hot melt adhesives

Mechanical Properties of Polyurethane Foams Prepared from Liquefied Corn Stover with PAPI.

Preparation of Waterborne Polyurethane Adhesives Based on Macromolecular-Diols Containing Different Diisocyanate

Improvement of Preparation Process and Characterization of Liquefied Rice Straw Based Polyurethane Foam

Polyurethane wood adhesive from palm oil-based polyester polyol

Preparation of bio-polyols by liquefaction of hardwood residue and their application in the modification of polyurethane foams

A facile strategy for synthesizing isosorbide-based polyurethane structural adhesives and core–shell rubber

Preparations and Properties of Polyurethane Adhesives Modified by Corn Straw Lignin

Synthesis and Characterization of Waterborne Polyurethane Adhesive from MDI and HDI

Polyurethane Adhesives Based on Oxyalkylated Kraft Lignin

Preparation, mechanical properties of waterborne polyurethane and crosslinked polyurethane‐acrylate composite

Synthesis and Characterization of Novel Polyurethane Acrylates Based on Soy Polyols

Preparation of Contamination Free Polyurethane Adhesive Based on Biopolymer Castor Oil

Study on the Properties of Polyurethane–Urea Elastomers Prepared by TDI/MDI Mixture

Preparation and Characterization of Heterogeneous Crosslinked Polyurethane

Preparation of Semirigid Polyurethane Foam with Liquefied Bamboo Residues