Abstract:In the past 3 decades, there has been great advancement in the preparation of microcellular thermoplastic polymer foams. However, little attention has been paid to thermoplastic elastomers. In this study, microcellular poly(ethylene-co-octene) (PEOc) rubber foams with a cell density of 2.9 x 10(10) cells/cm(3) and a cell size of 1.9 mu m were successfully prepared with carbon dioxide as the physical blowing agent with a batch foaming process. The microcellular PEOc foams exhibited a well-defined, closed-cell structure, a uniform cell size distribution, and the formation Of unfoamed skin at low foaming temperatures. Their difference from thermoplastic foam was from obvious volume recovery in the atmosphere because of the elasticity of the polymer matrix. We investigated the effect Of the molecular weight on the cell growth process by changing the foaming conditions, and two important effect factors on the cell growth, that is, the polymer matrix modulus/melt viscoelastic properties and gas diffusion coefficient, were assessed. With increasing molecular weight, the matrix modulus and melt viscosity tended to increase, whereas the gas solubility and diffusion coefficient decreased. The increase in the matrix modulus and melt viscosity tended to decrease the cell size and stabilize the cell structure at high foaming temperatures, whereas the increase in the gas diffusion coefficient facilitated cell growth at the beginning and limited cell growth because most of the gas diffused Out Of the polymer matrix during the long foaming times or at high foaming temperatures. (C) 2010 Wiley Periodicals, Inc. J Appl Polym Sci 116: 1994-2004, 2010

Study on Microcellular Foaming of Poly(phenylene sulifde)/Poly(ether ether ketone) Blends Using Supercritical Carbon Dioxide

Tailored Morphologies and Properties of High-Performance Microcellular Poly(phenylene Sulfide)/poly(ether Ether Ketone) (PPS/PEEK) Blends

Microcellular foaming of poly(phenylene sulfide)/poly(ether sulfones) blends using supercritical carbon dioxide

Effects of Processing Parameters and Thermal History on Microcellular Foaming Behaviors of PEEK Using Supercritical CO2

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Microcellular Foams of Glass-Fiber Reinforced Poly(phenylene Sulfide) Composites Generated Using Supercritical Carbon Dioxide

Microcellular Foaming Of Polypropylene/Polystyrene Blends Using Supercritical Fluid

Preparation of Microcellular Polypropylene/Poly(octene-ethylene) Foams by Using Supercritical Carbon Dioxide

Microcellular Foaming of Polysulfones in Supercritical CO2 and the Effect of Co-Blowing Agent

Study on Extrusion Foaming of Polypropylene/Polydimethylsiloxane Blends

Physical Properties of Microcellular Polymeric Foams with Supercritical CO2

Preparation of Microcellular Poly(Ethylene-Co-Octene) Rubber Foam with Supercritical Carbon Dioxide

Preparation of Microcellular Polypropylene/polystyrene Blend Foams with Tunable Cell Structure

Introduction of Stereocomplex Crystallites of PLA for the Solid and Microcellular Poly(lactide)/poly(butylene Adipate-Co-terephthalate) Blends

Preparation and Density Control of Pmma Microcellular Foams Via Supercritical Carbon Dioxide Foaming

Microcellular foaming of PP/PE blends with different viscosity and elasticity

Synergistic effects of in situ fibrillated polytetrafluoroethylene and polystyrene–butadiene block on the microcellular foaming behaviors of polyphenylene oxide modified by high‐impact polystyrene

Preparation and Cell Structure of Microcellular Polycarbonate

Preparation of Biodegradable PBST/PLA Microcellular Foams under Supercritical CO2: Heterogeneous Nucleation and Anti-Shrinkage Effect of PLA

Improving of Cell Structure of Microcellular Foams Based on Polypropylene/High-density Polyethylene Blends

Preparation and characterization of microcellular injection molded foams from high-performance blends based on PPS-modified PPBESK