Abstract:<p>Developing efficient and compact heat exchangers is of important significance to improve the energy utilization efficiency of entire society. 3D finned-tubes, as a kind of passive enhanced heat exchange technology, are widely used for improving the thermal-hydraulic performance of the heat exchanger. In the numerical study of 3D finned-tube heat exchanger, on account of the limit by computing capacity, it is very hard to carry out the full-size numerical simulation, so the method based on porous media model becomes a common approach for numerical simulation of the heat exchanger. In the present study with the discrete 3D finned-tube heat exchanger as the study object, a kind of approach based on the porous media model under the cylindrical coordinate system is proposed. In this approach, only the fin region on the surface of base tube is simplified to the annular porous media zone while the region beyond the fin tips is still regarded as the pure gas flow region. The resistance coefficients of annular porous media, which are used to represent the retardation effects of the fin on the fluid motion, are given under the cylindrical coordinate system. Based on serialized numerical simulations of the fin configuration model seen by the air when it flows in the circumferential, axial and radial direction, the viscous resistance coefficients and inertial resistance coefficients of the annular porous media zone in each direction are obtained through fitting. Through comparison of simulated values between the porous media model and 3D finned-tube practical physical model, it is found that the pressure drop calculated by the method based on porous media model proposed in this study agree well with that based on the real physical model. The pressure drop predicted by the porous media model also agree well with the experimental results. In the approach based on porous media model, the grid number and calculation cost are smaller than those in practical physical model. Especially in case of tube bundles, number of grids applied in the simulation based on porous media model is far less than the grid quantity in the practical physical model simulation, but the pressure drop obtained by the porous media model is almost equal to the result obtained from the practical physical model. Besides, in the present method, only the fin zone is deemed as the porous media, so the flow field in the region beyond the fin tips will still be solved as same as that in the full-size simulation. Thus more flow details within the heat exchanger can be captured. The approach based on porous media model under the cylindrical coordinate system proposed can be used in the simulation study of the internal flow field of 3D finned-tube heat exchangers in actual scale. On this basis, this approach can contribute to optimization design of the 3D finned-tube heat exchanger.</p>

Model for calculating water bridge volume retained between vertical fins

Flow and Heat Transfer Analysis of Perforated Fin in Compact Heat Exchanger

Simulations of Interaction Between Flow and a Thin Elastic Beam Using Cip-Based Model with Adaptive Mesh

Simplified heat exchange model of fan coil in wet cooling conditions

Airside Fin Efficiencies for Finned-Tube Heat Exchangers with Forced Convection

Three-Dimensional Numerical Simulation on the Laminar Flow and Heat Transfer in Four Basic Fins of Plate-Fin Heat Exchangers

A thermal calculation model for tubular condensing heat exchanger

Thermal-hydraulic performance evaluation of airside of wavy fin compact heat exchangers under wet conditions

Condensation in Horizontal Smooth Tubes: A New Heat Transfer Model for Heat Exchanger Design

A Three-Zone Analytical Model For Performance Prediction Of A Brazed Aluminum Evaporator Operating Under Dehumidifying Condition - Part 1 - Analysis Method

Numerical investigation of condensation characteristics of a moist air-to-air plate-fin heat exchanger and experimental validation

An approach based on the porous media model for numerical simulation of 3D finned-tubes heat exchanger

Review of experimentation and modeling of heat and mass transfer performance of fin-and-tube heat exchangers with dehumidification

Visualization experiment and numerical simulation on behaviors of gas-liquid falling film flow on the air-side of two-row plain finned-tube heat exchanger

Experimental Study of the Air Side Performance of Fin-and-Tube Heat Exchanger with Different Fin Material in Dehumidifying Conditions

Simulation of Fin-and-tube Heat Exchanger Based on Two-phase Fluid Network

A modeling study of spatial and temporal frost growth on the edge of windward fins for a tube-finned heat exchanger

Effect of partially wet-surface condition on the performance of fin-tube heat exchanger

Experimental and numerical study and comparison of performance for herringbone wavy fin and enhanced fin with convex-strips in fin-and-tube heat exchanger

Numerical simulation of heat transfer and flow characteristics for plate fin-and-tube heat exchanger with ring-bridge slit fins

Numerical investigation of heat transfer and flow resistance characteristics of interpenetrated flying-wing finned tubes