Abstract:The frost-free air-source heat pump (ASHP) with integrated liquid desiccant dehumidification is a more promising energy-saving alternative to the conventional ASHP unit. The performance of spray-type finned-tube heat exchanger (FTHE), as one of the key equipment of this frost-free ASHP system, is affected by a combination of various factors including wall wettability, liquid film flow pattern, liquid film thickness, velocity distribution in a liquid film, interface wave, interface velocity and so on. To provide a theoretical basis for the operation, design and optimization of high-performance spray-type FTHE, a visualization experiment system and a three-dimensional (3D) numerical model are employed to study the behaviors of counter-current gas-liquid falling film flow on the air-side of two-row plain FTHE under different parameters in the present paper. According to the experimental results, the flow pattern of liquid film on the finned-tube surface is a mixture flow composed of the rivulet flow and the thin falling film flow, demonstrating that the assumption of the uniform distribution for liquid film thickness proposed in previous studies is not completely consistent with the actual situation. Meanwhile, the numerical results indicate that the transient-average film thickness on the surface of two-row plain finned-tube is significantly 18.3% – 32.5% higher than that on the vertical plate calculated by Nusselt's model. After that, the critical gas and liquid Reynolds numbers of the flow pattern transition for the liquid film are obtained, and it is pointed out that the wall contact angle of 10° is more conducive to the formation of complete film flow on the air-side of the two-row plain FTHE within the fin pitch range of 4.8 – 6.0 mm. The changes of the falling liquid film and gas-liquid interface characteristics are fundamentally attributed to the drag effect of the interfacial shear force. Furthermore, there is a cubic curve relationship between average interface shear force and gas Reg. A quadratic curve relation exists between average wall shear stress and gas Reg. At the same time, the velocity of falling film fluid at the bottom region of laminar flow is reduced, resulting from the inhibiting effect of the interfacial shear force.

Numerical investigation of condensation characteristics of a moist air-to-air plate-fin heat exchanger and experimental validation

Thermal Design of Large Plate-Fin Heat Exchanger for Cryogenic Air Separation Unit Based on Multiple Dynamic Equilibriums

Numerical Analysis of Heat Transfer Characteristics of a Falling Film Type Plate-Fin Condenser/Reboiler

Experimental Study of the Air Side Performance of Fin-and-Tube Heat Exchanger with Different Fin Material in Dehumidifying Conditions

Numerical study on hydrodynamic characteristics of plate-fin heat exchanger using porous media approach

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Influence of Surface Modification on the Transient Dehumidification Performance of Fin-and-tube Heat Exchanger

Numerical and experimental study on intermittent spray cooling for plate-fin heat exchanger

Numerical Simulation of Heat Transfer in Finned Tube of Heat Recovery Unit Using Fluid-Solid Coupled Method

Numerical Simulation on Heat and Mass Transfer of Plate Evaporative Condenser

Effects of Experimental Parameters on Condensation Heat Transfer in Plate Fin Heat Exchanger

Review of experimentation and modeling of heat and mass transfer performance of fin-and-tube heat exchangers with dehumidification

Effect of flow maldistribution on heat transfer performance and temperature field of plate-fin heat exchangers

Visualization experiment and numerical simulation on behaviors of gas-liquid falling film flow on the air-side of two-row plain finned-tube heat exchanger

Numerical investigation on acid vapor condensation characteristics of honeycomb H-type finned tube heat exchangers with hexagonal fins

Experiment on Forced Convection-Condensation Heat Transfer Characteristics Based on Finned Plate Configuration

Study On The Performance Of Heat And Mass Transfer Of Cross Flow Dehumidifier In An Industrial Plant

RESEARCH ON THE HEAT AND MASS TRANSFER PERFORMANCE AND FLOW-PATI'ERN COMPARISON OF THE INTERNALLY-COOLED LIQUID DESICCANT DEHUMIDIFIERS

An experimental study of falling film evaporation in vertical channels with perforated fins of a plate-fin heat exchanger

Numerical analysis on heat and mass transfer of the planar membrane dehumidifier