Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Structural Optimization of Condensers with Refrigerant Blends Based on Heat Transfer and Pressure Drop Coupling

Thermodynamic optimization analysis of a tube-in-tube helically coiled heat exchanger for Joule-Thomson refrigerators

Initial Ratio Optimization for the Ejector Cooling System with Thermal Pumping Effect (ECSTPE)

Thermodynamic Performance Prediction Of Pulse Tube Refrigeration With Mixture Fluids

Theoretical Investigations on the Cycle Performance of a Single-Pressure Diffusion Absorption Heat Transformer with LiBr–H2O-R134a-TEGDME

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Performance of a Single-Stage Linde-Hampson Refrigerator Operating with Binary Refrigerants at the Temperature Level of −60 °C

Numerical simulation of condensation heat transfer and pressure-drop performance of R22 and R407C in horizontal microfin tube

Condensation heat transfer and pressure drop characteristics inside smooth and enhanced tubes with R410A and R32

Effect of Mixed Refrigerant Composition on Performance of an Auto-Cascade Refrigeration System Using R600a/R1150/R14

An Experimental Study of R410A Condensation Heat Transfer and Pressure Drops Characteristics in Microfin and Smooth Tubes with 5 Mm OD

Entropy Generation of R513A Condensation Flow Inside the Horizontal Microfin Tubes

Condensation Heat Transfer Experiments of R410A and R32 in Horizontal Smooth and Enhanced Tubes

Condensation of R134a and R22 in Shell and Tube Condensers Mounted with High-Density Low-Fin Tubes

Study on Refrigerant Circuitry Design for Condensers

Influence of refrigerant circuitry on performance of R410A condensers

Condensation heat transfer and pressure drop of r134a in horizontal micro-scale enhanced tube

Supercritical Heat Transfer Characteristics and System Performance Analysis of R744 and Its Two Azeotropic Blends

A New Structural Optimization Method for Distributors in R290 Air Conditioner with Small Diameter Copper Tubes

Performance Analysis of a New Transcritical R744 Refrigeration Cycle with Expander-Mechanical Overheating

Development of Small-diameter Tube Heat Exchanger : Circuit Design and Performance Simulation