Abstract:This paper introduces adsorption processes with scaled sizes for post-combustion carbon capture, pre-combustion carbon capture, and direct air capture (DAC). Technical characteristics, separation performances, and operating energy consumptions of adsorption-based pilot plants for carbon capture are analyzed. Opportunities and challenges of adsorption-based carbon capture processes in future development are illustrated. Adsorption-based post-combustion carbon capture is a relatively mature technology, which can be applied to retrofitted power plants. However. in order to commercialize this technology, quantities of research and development resources are still needed. Researches on adsorption-based post-combustion carbon capture should focus on the following three aspects: (1) Low-temperature adsorbents with excellent CO2 working capacities, kinetics, and stabilities, (2) low energy consumption cycles using steam purge, and (3) contactors with low gas-solid mass transfer resistances. The warm gas clean-up technology based on pressure swing adsorption (PSA) is a research hotspot for pre-combustion carbon capture. At present, many warm gas clean-up pilot plants are being built worldwide, and in the meantime, some bottlenecks appear. First. the CO2 working capacities of elevated temperature adsoibents are still lower than those of low temperature adsorbents. The recently reported molten salt-promoted magnesium oxide achieves a very high working capacity through the bulk phase chemical absorption, but a carbon capture prototype needs to be established to verify its cyclic stability. Achieving both high purity and high recovery of warm gas clean-up consumes a large amount of high temperature steam. Although multi-train PSA configuration can reduce the energy consumption. it also increases the operating complexity and equipment investment. In addition to CO2 the removal of other impurities such as H2S, COS, HCl, and heavy metals in syngas/reforming gas should be considered. The sorption enhanced reforming with oxy-fuel regeneration process based on high temperature adsorbents can achieve CO2 enrichment in the regeneration reactor. However, pilot plants for this technology are currently lacking, and so detailed techno-economic analysis is still needed to assess its capture cost. Although DAC is a relatively new concept and is still in the early stage for large-scale commercial application, the synergy between DAC and conventional carbon capture technologies can mitigate climate change effects in the long run. The development of DAC technologies needs to pay special attention to the pressure drop problems. Novel gas-solid contactors using structural adsorbents can effectively reduce the power consumption of the fan. Steam purge under subatomospheric pressures reduces the regeneration temperature of DAC, and thus makes the utilization of renewable energy and industrial waste heat for regeneration becoming possible. When steam purge is used, the cyclic stability of the adsoibents should be concerned. For instance. polyamine impregnated adsoibents are prone to amine leakage in the presence of steam. Therefore. the development of hydrothermally stable DAC adsorbents is significantly important.

Practical Experience in Post-combustion CO2 Capture Using Reactive Solvents in Large Pilot and Demonstration Plants

Reducing Aerosol and Ammonia Emission in Post-Combustion CO2 Capture: Additives As Key Solutions

Recent technological developments in post combustion CO2 capture amine scrubbing process in commercial plants

Development and testing of a new post-combustion CO2 capture solvent in pilot and demonstration plant

The Advances of Post-combustion CO2 Capture with Chemical Solvents: Review and Guidelines

Recent Advances and Challenges in Ionic Materials for Post-Combustion Carbon Capture

Aqueous Ammonia Based Post Combustion Capture: Results from Pilot Plant Operation, Challenges and Further Opportunities

Post-Combustion CO2 Capture Demonstration Using Supported Amine Sorbents: Design and Evaluation of 200 Kwth Pilot

Phase Change Solvents for Post-Combustion CO2 Capture: Principle, Advances, and Challenges

Advances in Post‐Combustion CO 2 Capture by Physical Adsorption: From Materials Innovation to Separation Practice

Recent Progress of Amine Modified Sorbents for Capturing CO2 from Flue Gas

Pilot-Scale Experimental Study on the CO2 Capture Process with Existing of SO2: Degradation, Reaction Rate, and Mass Transfer

Recent progress in carbon dioxide capture technologies: A review

Ammonia-based post-combustion CO2 and SO2 integrating capture using multi-stage solvent circulation process

The Latest Advances in Carbon Dioxide Capture Technologies

Research progress of pre-combustion CO2 capture

Experimental Study of the Absorption and Regeneration Performance of Several Candidate Solvents for Post-Combustion CO2 Capture

Research Progress on CO2 Capture and Utilization Technology

Large-scale Applications and Challenges of Adsorption-Based Carbon Capture Technologies

Membrane technology for CO2 capture: From pilot-scale investigation of two-stage plant to actual system design

Experimental Study on Postcombustion Systems Including a Hollow Fiber Membrane and a Packed Column