Abstract:Homemade nano-agglomerated powders 8YSZ powders for PS-PVD were prepared by the spray drying, then calcination processes at four different temperatures (500 °C, 700 °C, 900 °C and 1100 °C) were carried out on the spray-dried powders. Checked by laser particle sizer, scanning electron microscope (SEM) and X-ray diffraction (XRD), the physical properties, microstructure and phase constitutions of the calcined powders were investigated. The results show that the size of powders calcined at 500 °C is increased relative to the spray-dried powder, whereas the powders calcined at 700 °C, 900 °C and 1100 °C possess smaller size. The binding force of the primary particles tend to rise with the increase of calcination temperature. When the temperature was up to 900 °C and above, it was found that the sintering neck indicating with strong binding was formed between the primary particles. In parallel, the powders underwent an m-ZrO2 to t-ZrO2 transition as the calcination temperature rose. It is also found that the PS-PVD prepared coatings which were obtained by using the above powders undergo a transformation from a feather-like to a dense laminate structure as the calcination temperature rises. It is noteworthy that the coating obtained by the powders calcined at 700 °C have a special three-layer composite structure of near dense surface layer, columnar intermediate layer and dense sub-layer. The composite structural coating has excellent adhesion and thermal shock resistance, with a bonding strength of 81MPa and no major spalling when water quenched 100 cycles at 1100 °C.

Preparation and Characteristics of Sm2Zr2O7Agglomerated Powders for Plasma Spraying

Preparation and characterization of nanostructured La2Zr2O7 feedstock used for plasma spraying

Optimization of Yb2O3-Gd2O3-Y2O3 Co-Doped ZrO2 Agglomerated and Calcined Powders for Air Plasma Spraying

Preparation and Properties of ZrB2-MoSi2-glass Composite Powders for Plasma Sprayed High Temperature Oxidation Resistance Coating on C/SiC Composites

Research Progress of the Preparation of Zirconia Hollow Sphere Powder and the Performance of Its Coating

Fabrication and characterization of spray dried Al2O3–ZrO2–Y2O3 powders treated by calcining and plasma

Preparation and characterization of rare earth modified nanocrystalline Al2O3/13 wt%TiO2 feedstock for plasma spraying.

Plasma Characteristics and Coating Microstructures of Yttria Stabilized Zirconia During Plasma Spray Physical Vapor Deposition

Deposition Characteristics, Sintering and Cmas Corrosion Resistance, and Mechanical Properties of Thermal Barrier Coatings by Atmospheric Plasma Spraying

Fabrication and Characterization of Novel Powder Reconstitution Derived Nanostructured Spherical La2(Zr0.75Ce0.25)2O7 Feedstock for Plasma Spraying

Study on Wear Resistance and Spraying Process of Nano-ZrO2 Powder Plasma Spraying Coating

Deposition Characteristics of SrZrO3 Thermal Barrier Coating Prepared by Solution Precursor Plasma Spray Process

Microstructural study of nanostructured Zro 2 based thermal barrier coatings fabricated by high efficiency supersonic plasma spraying

Optimization of Alumina Slurry Properties and Drying Conditions in the Spray Drying Process and Characterization of Corresponding Coating Fabricated by Atmospheric Plasma Spray

Preparation of ZrO2 microspheres by spray granulation

Research on the Structure of Nanostructured Zirconia Coatings Deposited by Plasma Spraying

Microstructure and Deposition Mechanism of Suspension Plasma Spraying Thermal Barrier Coatings

Nanostructured Yttria Stabilized Zirconia Coatings Deposited by Air Plasma Spraying

Very low-pressure plasma-sprayed dense yttria-stabilized zirconia coatings using an axial bi-cathode plasma torch

Effect of calcination temperature on the microstructure, composition and properties of nanometer agglomerated 8YSZ powders for plasma spray-physical vapor deposition (PS-PVD) and coatings thereof

Influence of Plasma Spray Parameters on the Microstructure and Property of ZrO2-7 wt%Y2O3 Coating