Abstract:To improve the anti-oxidation ability of graphite, Al2O3 and SiC as additives, a uniform SiC coating was prepared on the surface of HTR graphite spheres by the pack cementation and sintering process. The microstructure of SiC coating was characterized by XRD, Raman spectroscopy, scanning electron microscopy, and the effect of Si/C ratio, Al2O3 and SiC content in the starting powder, sintering process conditions on the microstructure of SiC coating was also analyzed. The results show that the SiC coating on the surface of spherical graphite sample can be obtained with Si/C ratio higher than 3: 1, and the SiC coatings with different raw materials possess different microstructure and phase constitutes. The SiC coating is a kind of clear porous microstructure, while the main composition of the coating is β-SiC with some α-SiC and unreacted graphite. It is found that the content of Al2O3 has a significant influence on the penetration into the SiC coating, while the SiC content has a great influence on the microstructure between SiC coating and the substrate. When Al2O3 content is 10%, the bonding between the SiC coating and the substrate is better. When SiC content is 20%, the SiC coatings obtained have good densification and less lamellar accumulation of on the surface of the coatings. The SiC coatings sintered in Ar gas at 1750 °C have larger thickness and porous porosity microstructure, and the maximum thickness, about 400 ∼ 600 μm, can be achieved with the 2h of sintering time. The obtained SiC coatings sintered in vacuum at 1750 °C have a plate-like dense microstructure, in which the main composition of the coating is free Si, α-SiC and β-SiC, and the transitional area between SiC coating and the substrate is not obvious.

The Inlfuence of Water Content on the Property and Structure of SiC Honeycomb Ceramic by Extrusion Molding Technology

Preparation and Pore Structure Characteristics of SiC Honeycomb Ceramics with Macroporous Walls

Preparation and properties of SiC honeycomb ceramics by pressureless sintering technology

Preparation of Porous SiC Ceramic Using Bamboo Charcoal and Silica Sol As Pore-Forming Agents

Fabrication and Mechanical Properties of SiCw(p)/SiC-Si Composites by Liquid Si Infiltration using Pyrolysed Rice Husks and SiC Powders as Precursors

Effect of Different Particle Sizes and Pore-Making Agent Ratio on Properties of SiC Porous Ceramics

Fabrication, Structure and Properties of Porous SiC Ceramics with High Porosity and High Strength

Microstructure Evolution and Performance Improvement of Silicon Carbide Ceramics via Impregnation Method

Effects of Sintering Additives on Microstructure and Properties of Porous SiC Ceramics with High Porosity

Microstructures, Mechanical Properties and Electromagnetic Wave Absorption Performance of Porous SiC Ceramics by Direct Foaming Combined with Direct-Ink-Writing-Based 3D Printing

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

Porous SiC Ceramics with Controllable Porosity Achieved by Micro-sized Powder through Recrystallization Sintering

Influence of polycarbosilane composition on the properties of SiC/SiC composite fabricated by precursor infiltration and pyrolysis process

Microstructure and mechanical properties of continuous carbon fiber-reinforced SiC ceramic composite fabricated by direct ink writing

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Additive manufacturing of Csf/SiC composites with high fiber content by direct ink writing and liquid silicon infiltration

Effects of carbon content on microstructure and mechanical properties of SiC ceramics fabricated by SLS/RMI composite process

Effect of SiC content on the mechanical behaviour of a three-dimensional needled C/SiC composite

Preparation and mechanical properties of SiCw-reinforced WC-10Ni3Al cemented carbide by microwave sintering

Porous SiC using polycarbosilane/camphene solutions: Roles of freeze casting parameters

EFFECT OF AL(2)O(3) AND SIC CONTENT IN PACK CEMENTATION POWDERS ON THE MICROSTRUCTURE OF SIC COATINGS ON HTR GRAPHITE SPHERES