Abstract:Particulate emissions from homogeneous charge compression ignition (HCCI)engines are often considered as negligible and the measurement of particulate matter (PM) with HCCI combustion systems has been rare. An earlier publication in the literature and the authors' own recently published work suggest that PM emissions from gasoline direct injection (DI) HCCI engines should not be neglected. It has been shown that PM emissions from HCCI engines, although generally lower, can be similar to spark ignition (SI) levels for certain engine conditions, especially in the accumulation mode. The present work shows that although injection timing is effective for control of HCCI, it can have a significant impact on PM emissions. Engine speed also appears to have an impact on PM emissions for the HCCI combustion mode. Typically for HCCI operating at 1500 r/min, the total mass and total number of the PM emissions could be up to six times higher when the fuel is injected during the recompression period compared with the case for injection during the inlet valve open period. Similarly, when the engine was operated in SI mode, an attempt to inject fuel close to induction top dead centre (TDC) made the PM emission noticeably higher, reaching unacceptable levels. The split injection strategy for HCCI mode has been investigated for its effect on PM emissions. It has been found that the PM. number concentration for split injection lies between the maximum concentration measured for very early injections (near TDC at recompression) and the minimum concentration measured for the latest injections used (at crank angles near to the inlet valve maximum opening time), with the magnitude of number density varying approximately from 0.2 to 1.2 million/cm(3). It is also observed that for split injection the number of particulates in nucleation mode varies less, while the number in accumulation mode level varies within a limit of one order of magnitude; both are dependent on the injection strategy. The shape of the PM distribution is such that the nucleation mode exceeds the number concentration of 1 x 10(7) (dN d log D-p) and the accumulation mode falls parabolically to approximately 1 x 10(6). For comparison, it can be said that the PM number concentration measured in the authors' engine is approximately one order of magnitude lower in accumulation mode than the level for a typical modern diesel engine.

Effect of injection timing on PM emissions from DMCC engine

Study on injection characteristics of diesel and DME

Effect of diesel late-injection on combustion and emissions characteristics of diesel/methanol dual fuel engine

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Effects of injection timing on combustion performance and emissions in a diesel engine burning biodiesel blended with methanol

Experimental investigations of the effects of pilot injection on combustion and gaseous emission characteristics of diesel/methanol dual fuel engine

Effects of diesel pre-injection on the combustion and emission characteristics of a common-rail diesel engine fueled with diesel-methanol dual-fuel

Effect Of Injection Timing On Gasoline Homogeneous Charge Compression Ignition Particulate Emissions

The effect of diesel pilot injection strategy on combustion and emission characteristic of diesel/methanol dual fuel engine

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Effect of Injection Strategy on Emission Characteristics of Compression Ignition Engine Fueled with Blended Fuel

Effect of injection strategy on a diesel/methanol dual-fuel direct-injection engine

Effect of Post-Injection on Combustion and Exhaust Emissions in DI Diesel Engine

An optical study on the cross-spray characteristics and combustion flames of automobile engine fueled with diesel/methanol under various injection timings

Numerical Investigation of the Effect of Injection Timing on the In-Cylinder Activity of a Gasoline Direct Injection Engine

Effects of injection and spark timings on combustion, performance and emissions (regulated and unregulated) characteristics in a direct injection methanol engine

Experimental Investigation on the Effects of Direct Injection Timing on the Combustion, Performance and Emission Characteristics of Methanol/Gasoline Dual-Fuel Spark Turbocharged Ignition (DFSI) Engine with Different Injection Pressures under High Load

Study of the Influence of Methanol/f-T Diesel Combustion Particle Materiality Parameters on the Deposition Process in Diesel Particulate Filter Trap Units

Effects of Methanol Addition on the Combustion Process of the Methanol/Diesel Dual-Fuel Based on an Optical Engine

Numerical Investigation on the Influence of Injection Location and Injection Strategy on a High-Pressure Direct Injection Diesel/Methanol Dual-Fuel Engine

A comparative study on operating range and combustion characteristics of methanol/diesel dual direct injection engine with different methanol injection timings