Abstract:Tip clearance has great influence on the performance of multistage axial compressors including efficiency, pressure rise, mass flow, as well as matching. This paper reports a study into the influence of tip clearance on the performance and matching of a 5-stage axial compressor by a numerical method. Different tip clearances from 0% to 5.0% span which represents the typical range of tip clearance in modern multistage axial compressors were simulated and analyzed. The results show that as tip clearance increases from 0% to 5.0% span, the choked mass flow decreases by about 21.8%, the peak pressure ratio decreases by about 43.1% and the peak efficiency decreases about 14.3 percents. As tip clearance increases, the efficiency of the whole compressor decreases in a parabolic manner not linearly as previous suggested, which is partially attributable to the cantilevered stators considered in this paper and primarily due to the mismatching of different stages. It is of great importance to control the tip clearance. When tip clearance increases, the front stage tends to work near surge condition and the rear stage tends to work near choke condition, which leads to lower efficiency than in the middle stages. A weight was defined to evaluate each stage's contribution to the whole compressor's efficiency deficit caused by the increase of tip clearance. Front and rear stages contribute more to the efficiency deficit than the middle stages, which indicates that more attention should be paid on front and rear stages to improve the performance of multistage axial compressors. In order to evaluate the matching of multistage axial compressors with a quantified method, a new parameter named "Peak Efficiency Deviation (PED)" was defined based on the difference between each stage's operating efficiency and its peak efficiency. The mass flow of multistage axial compressors should be well considered to make the PED parameter to be close to zero as possible. In the most commonly used range of tip clearance from 0.5% to 3.0% span, the PED varies little within 0.4 percent, which is only about 8.4% of the peak efficiency deficit at 1.5% span tip clearance. So, the PED could be small within a wide range of tip clearances if the matching of the compressor is perfect at design tip clearance.

Research on Influence of Tip Clearance Effects on Transonic Compressor Performance

Numerical investigation on the influence of nonuniform tip clearance on rotor tip-clearance flow field structure

Effect of Nonuniform Tip Clearance on the Performance of Transonic Axial Compressors

Vortex structure control based bleed in axial compressor cascade with tip clearance using large eddy simulation

Quantification Of Performance Uncertainty For A Transonic Compressor Rotor Using An Adaptive Nipc Method

Effect of Tip Clearance on Compressor Performance

AERODYNAMIC ANALYSIS OF A 7-STAGE AXIAL COMPRESSOR WITH VARIOUS TIP CLEARANCES IN ROTOR

Numerical Simulation Of A Transonic Centrifugal Compressor Blades Tip Clearance Flow Of Vehicle Turbocharger

Research on Transonic Centrifugal Compressor Blades Tip Clearance Distribution of Vehicle Turbocharger

Influence Of Tip Clearance On The Performance And Matching Of Multistage Axial Compressors

Effects of Circumferentially Non-Uniform Clearance on the Spanwise Flow Characteristics in a Transonic Compressor Rotor

Investigation on the Interaction of Tip Leakage Flow/ Shock Wave/ Boundary Layer in a Transonic Compressor Stage

Effects of tip clearance on flow field and performance of a centrifugal compressor

Research on the effect of centrifugal compressor blade tip clearance distribution on conbustion engine turbocharger performance

A numerical study on the tip clearance in an axial transonic compressor rotor

Influence of the Tip and Axial Clearances on the Aerodynamic Performance of a Helium Compressor

Numerical investigation of the unsteady tip leakage flow and rotating stall inception in a transonic compressor

Numerical investigation of tip clearance effects on rotating instability of a low-speed compressor

Influence of Tip Clearance on Performance of A Contra-Rotating Fan

An 11-Stage Axial Compressor Performance Simulation Considering the Change of Tip Clearance in Different Operating Conditions

Influence of Blade Tip Surface Roughness on the Performance of a Single-Stage Axial Flow Compressor