A numerical study on the tip clearance in an axial transonic compressor rotor

Xiaodong Ren,Chun-wei Gu

DOI: https://doi.org/10.1016/j.applthermaleng.2016.04.082

IF: 6.4

2016-01-01

Applied Thermal Engineering

Abstract:•An improved blockage indicator is proposed to quantify the blockage.•Tip clearance flow has a significant influence on the blockage in the rotor.•Tip clearance flow in the transonic rotor can be divided into two parts.

What problem does this paper attempt to address?

Effects of tip clearance flow on aerodynamic performance of transonic axial compressor rotor

Yuanyuan LI,Chuhua ZHANG,Junfeng XIAO,Song GAO,Bo SHANGGUAN,Feilong YU

DOI: https://doi.org/10.3969/j.issn.1002-3364.2014.12.072

2014-01-01

Abstract:On the basis of a time-marching code in house,the internal three-dimensional turbulent flow field of a transonic axial compressor Rotor3 7 with seven tip clearances is numerically studied.The effects of tip clearance flow on aerodynamic performance of the transonic axial compressor rotor are investigated.The re-sults show that,with a decrease in the tip clearance,the aerodynamic efficiency and pressure ratio increase and the stable operation area enlarges significantly.The relationship between the aerodynamic performance and the tip clearance deviates far away from the linear function and appears the curve characteristics.For this rotor,the optimal tip clearance 0.178 mm is a compromise between aerodynamic and structural require-ments.
The Influence of Blade Root Fillet and Blade Tip Clearance on the Aerodynamic Performance of a Transonic Axial Compressor

MAO Ming-ming,SONG Yan-ping,WANG Zhong-qi

DOI: https://doi.org/10.3969/j.issn.1001-2060.2005.05.005

2005-01-01

Abstract:Through the numerical simulation of the flow field of a single-stage transonic axial compressor a study was conducted of the impact of rotating-blade root fillet and tip clearance on the flow field aerodynamic performance.The results of the study indicate that the blade tip clearance will lead to a flow blockage at the top zone and increase the separation loss at that zone.The blade root fillet will decrease the flow turning angle at the blade root,decrease work-performing capacity and enlarge the blade root separation zone.This will lead to a decrease in flow rate and an increase in separation loss at the root zone.In view of the above,the rotating blade tip clearance and the blade root fillet should be taken into account in order to enhance the accuracy of the numerical simulation.
Numerical investigation on the influence of nonuniform tip clearance on rotor tip-clearance flow field structure

Guochen Zhang,Zhipeng Li,Zhiyuan Cao,Zhihui Xu,Weihang Liu

DOI: https://doi.org/10.1016/j.heliyon.2024.e25296

IF: 3.776

2024-02-01

Heliyon

Abstract:A numerical study was conducted on an axial compressor, the NASA Stage 35, with three nonuniform tip clearances to understand the effect of a different shape tip clearances rotor on the compressor's performance. The results demonstrated that by modifying the traditional parallel tip clearance to sine-type tip clearance (STC), hump-type tip clearance (HTC), and concave-type tip clearance (CTC), the compressor's peak efficiency showed remarkable improvement and the SMI was significantly improved. In comparison to the design rotor, the SMI of STC, HTC, and CTC increased by 3.102 %, 2.672 %, and 0.645 %, respectively. The leakage distribution at the tip-clearance region from LE to TE exhibited an inverse pattern to that of the tip curve. The leakage's magnitude could not reflect the TLF's intensity, and the leakage in the middle of the blade tip had a role in the size of the TLV. Leakage at the tip's TE influenced the corner separation's scale in the casing. The STC and HTC schemes' total pressure ratio improved, the low-velocity zone's area, high-entropy area, and high absolute vorticity area at the LE of rotor's PS decreased, the detached shock moved backward, the leading-edge spillage flow decreased, the shock action position of the rotor suction surface moved forward, the BLS increased, the TPL in the stator channel decreased, and the CTC exhibited the opposite trend. A nonuniform tip clearance was achieved by reducing the leakage and TLV intensity, thereby reducing the size of the TLV, induced vortex, or CSV in rotor passage and increasing the compressor's SMI.
Effect of Tip Clearance Size on the Performance of a Low-Reaction Transonic Axial Compressor Rotor

Wei Zhu,Songtao Wang,Longxin Zhang,Jun Ding,Zhongqi Wang

DOI: https://doi.org/10.1177/0957650919856541

2020-01-01

Abstract:This study aimed to enhance the understanding of flow phenomena in low-reaction aspirated compressors. Three-dimensional, multi-passage steady and unsteady numerical simulations are performed to investigate the performance sensitivity to tip clearance variation on the first-stage rotor of a multistage low-reaction aspirated compressor. Three kinds of tip clearance sizes including 1.0τ, 2.0τ and 3.0τ are modeled, in which 1.0τ corresponds to the designed tip clearance size of 0.2 mm. The steady numerical simulations show that the overall performance of the rotor moves toward lower mass flow rate when the tip clearance size is increased. Moreover, energy losses, efficiency reduction and stall margin decrease are also observed with increasing tip clearance size. This can be mostly attributed to the damaging impact of intense tip clearance flow. For unsteady simulation, the result shows periodical oscillation of the tip leakage vortex and a “two-passage periodic structure” in the tip region at the near-stall point. The occurrence of the periodical oscillation is due to the severe interaction between the tip clearance flow and the shock wave. However, the rotor operating state is still stable at this working point because a dynamic balance is established between the tip clearance flow and incoming flow.
NUMERICAL SIMULATION STUDY ON THE EFFECT OF TIP CLEARANCE ON PERFORMANCE OF A TRANSONIC AXIAL FAN

JIANG Bin,WANG Song-Tao,SUN Xi-Miao,WANG Zhong-Qi

DOI: https://doi.org/10.3321/j.issn:0253-231X.2008.10.009

2008-01-01

Journal of Engineering Thermophysics

Abstract:A numerical study on the effect of different tip clearance size on the performance of a low aspect ratio transonic fan with tandem cascade has been carried through.Five different levels of relatively tip clearances are 0%,0.132%,0.396%,0.66%,1.32% respectively.The result indicates that with the increase of tip clearance size,the performance of fan stage changes obviously.Tip clearance influences shock and interaction between shock and boundary layer near the tip for transonic fan/compressor.The block and loss at tip region has great important relation with the leakage flow.
Influence of Tip Clearance on Flow Characteristics of Axial Compressor

Moru Song,Hong Xie,Bo Yang,Shuyi Zhang

DOI: https://doi.org/10.3390/pr8111445

IF: 3.5

2020-01-01

Processes

Abstract:This paper studies the influence of tip clearance on the flow characteristics related to the performance. Based on full-passage numerical simulation with experimental validation, several clearance models are established and the performance curves are obtained. It is found that there exists an optimum clearance for the stable working range. By analyzing the flow field in tip region, the role of the tip leakage flow is illustrated. In the zero-clearance model, the separation and blockage along the suction side is the main reason for rotating stall. As the tip clearance is increased to the optimum value, the separation is suppressed by the tip leakage flow. However, with the continuing increasing of the tip clearance, the scale and strength of the tip clearance vortex is increased correspondingly. When the tip clearance is larger than the optimum value, the tip clearance vortex gradually dominates the flow field in the tip region, which can increase the unsteadiness in the tip region and trigger forward spillage in stall onset.
An Improved Model for Tip Clearance Loss in Transonic Axial Compressors

Shubo Ye,Qingjun Zhao,Weiwei Cui,Guang Xi,Jianzhong Xu

DOI: https://doi.org/10.1177/0957650917736453

2017-01-01

Proceedings of the Institution of Mechanical Engineers Part A Journal of Power and Energy

Abstract:An improved compressible model for estimating tip clearance loss in transonic compressors is presented with the emphasis on the effects of blade tip loading distribution and double leakage flow. Tip clearance flow is treated as three parts along the chord and the progressive relations from upstream to downstream part is revealed to be responsible for the formation of tip clearance flow. Control volume method is applied to simplify the mixing process and calculate the mixed-out loss for the three parts, separately. Computational study shows that mass flow of the incoming flow entering the control volume is consistent with that passing through an equivalent area of about half of tip leakage vortex region. The new model reveals that the second part of tip clearance flow has a larger mixed-out loss capacity than the two other parts. This difference is attributed to two factors: larger injection flow angle and more enrolled incoming flow, and both factors tend to increase the mixed-out loss. The success of the model implies that blade design or flow control strategies turning the tip clearance/main flow interface’s arrival onto blade tip pressure side downstream and the shock’s impingement point onto blade tip suction side upstream may be beneficial in desensitizing compressor performance to tip clearance size, without trading off pressure rise.
Numerical Study of the Flow in Axial Cascade with Tip Clearance

李巍,王国强

DOI: https://doi.org/10.3321/j.issn:1006-2467.2000.12.028

2000-01-01

Abstract:An artificial compressibility approach was applied for the numerical simulation of the turbulent flow field in an axial cascade with tip clearance. The numerical results indicate that the process of the tip vortex formation is delayed with the decreasing of the tip clearance. Its strength weakens rapidly. The range of its influence becomes smaller. The core of the tip vortex moves from the suction surface to the pressure surface along the direction of the flow. The coefficient of the pressure at the blade surface is reduced to some extent due to the existence of the tip clearance, especially near the tip of the blade. The effect of the vortex becomes smaller at the region of center and the root of the blade when the clearance decreases. The existence of clearance will result in the decreasing of the main stream and increasing of the secondary velocity near the tip of the blade obviously. The significant influence upon the characeteristics of the flow occurs when the clearance is from 2% chord to 5% chord.
Numerical Simulation of tip clearance flow inside turbine rotors

NIU Mao-sheng,ZANG Shu-sheng,HUANG Ming-hai

DOI: https://doi.org/10.3969/j.issn.1009-2889.2008.04.007

2008-01-01

Abstract:Tip clearance flow is one of the most important resources of losses in turbine rotors,but it's difficult to measure detailed flows and the distribution of static pressure inside the gap,due to the tiny size and the flow direction which is same with the direction of blade rotation.This paper presents a numerical simulation of the designed condition of the LISA 1.5-stage axial turbine,using the measurement results to validate the simulation and obtaining the distribution of pressure and flows inside the gap,meanwhileanalyzing effect of tip gap height on flows inside gap.
Numerical Investigations on Aerodynamic Blockage Characteristics and Exit Blockage Prediction Model for Transonic Centrifugal Impellers

ZHANG Chaowei,DONG Xuezhi,LIU Xiyang,GAO Qing,TAN Chunqing

DOI: https://doi.org/10.33737/gpps19-bj-173

2019-01-01

Abstract:This paper investigates the effect of the exit flow coefficient, rotational speed and tip clearance size on the exit aerodynamic blockage. An improved model is established to predict the exit aerodynamic blockage for transonic centrifugal impellers. The goal of numerical analysis and modeling is to supply an effective means of estimating exit aerodynamic blockage for use in the performance prediction stage. The numerical results show that decreased exit flow coefficient, enhanced rotational speed, and increased tip clearance size can increase the exit aerodynamic blockage. The inlet blockage contributes to the exit blockage and it is mainly affected by the interaction of the shock wave with the tip leakage vortex. The improved model considers the interaction of the shock wave with the tip leakage vortex, based on the conventional model. Compared with the conventional model, the improved model shows better accuracy, with an average relative error below 9.79%.
Tip Injection in Transonic Axial Compressor Rotor

Wen-sheng MA,Chun-wei GU

DOI: https://doi.org/10.3321/j.issn:1001-4055.2009.03.009

2009-01-01

Abstract:Tip injection with circumferential groove is adopted for investigating its effect on performance and inner flow feature in an axial transonic compressor rotor.Numerical simulation results indicate that tip injection can significantly improve the compressor stall margin,at the same time,result in an efficiency penalty.The comparison of various injection flow rates and angles shows that tip injection with 0.5% choke mass flow and at about 0° injection angle is most inspiring,which brings the stall margin increase by 10% and an acceptable efficiency penalty less than 0.5%.Through more analysis in flow field,the mechanism of tip injection for controlling the tip region flow,improving the stall margin and resulting in efficiency penalty is revealed.
Numerical Investigation of Tip Clearance Flow in a Variable Geometry Turbine with Non-Uniform Partial Clearance

Yueqi Liu,Shaowen Chen,Songtao Wang

DOI: https://doi.org/10.1515/tjj-2023-0063

2024-01-01

Abstract:In variable geometry turbine vanes, tip clearance height and shape vary with the rotation of the vane, which affect the aerodynamic performance significantly. However, these issues are rarely considered in published studies. The current paper investigated the flow field features of transonic variable geometry turbine vanes with non-uniform partial clearance induced by the vane rotating. The results show that: The influence of guide vane rotation on the clearance height and its distribution cannot be ignored. At the same turning angle, the maximum clearance difference is up to 0.79 mm (0.8 % vane height). The height and shape variation of the non-uniform clearance leads to the change in the leakage flow rate, secondary flow structure, and aerodynamic loss of the variable guide vane. Under the combined effect of pressure difference on both sides of the clearance, axial and circumferential non-uniformity of clearance height, the total pressure loss coefficient is up to 9.44 % when the turning angle is -10 degrees. The effect of the pivot on the clearance flow was also analyzed. The pivot increases the pressure in the gap flow field and reduces leakage flow velocity. However, a backflow region appears at the suction side of the pivot, which increases the aerodynamic losses.
Effect of Different Tip Clearance Treatments on Performance of an Axial-flow Compressor

Li WANG,Ming-min ZHU,Shao-peng LU,Jin-fang TENG

DOI: https://doi.org/10.3969/j.issn.1671-1815.2018.05.055

2018-01-01

Abstract:Different tip clearance treatments were studied on a typical axial compressor by means of CFD simu-lation to improve efficiency and stability. An innovated slope trench tip gap was designed and implemented besides traditional trench and stepped tip gap. The results showed that there existed backflow regions near the head of both trench and stepped tip gap as well as in the midstream of rotor tip,in addition,higher entropy increment was wit-nessed upstream from the tail of stepped tip gap. The newly designed slope trench tip gap was able to eliminate the backflow regions near the head of the trench and stepped tip gap;optimum peak position of the slope trench dimin-ished the backflow region in the midstream of rotor tip and further reduced loss. Design efficiency improved by 0.12% and stall margin improved by 8.3% when the slope trench was implemented, whose depth was 0.2 mm, penetration depth of the rotor tip was 0,and peak position was 6% axial chord length downstream from the leading edge of rotor tip.
Effects of Circumferentially Non-Uniform Clearance on the Spanwise Flow Characteristics in a Transonic Compressor Rotor

Weiwei Cui,Yuqiang Liu,Xinyuan Chen,Changlong Ruan,Fei Yao,Xinglu Wang,Laishun Yang,Cuiping Wang,Guangxi Yue

DOI: https://doi.org/10.1016/j.ast.2023.108162

IF: 5.457

2023-01-01

Aerospace Science and Technology

Abstract:The circumferentially non-uniform clearance has significant effect on the overall performance and operation safety of high loading compressor rotors. However, both the variation rules and mechanism of flow characteristic in the circumferential, radial and streamwise directions caused by the asymmetric clearance are not fully clarified, which restricts the performance degradation assessment and rubust design of high loading compressors. Therefore, different types of asymmetric tip clearance were designed in this paper to reveal the circumferential fluctuation laws and induced mechanism of key characteristic parameters in full-channel domains of compressor rotor with circumferentially non-uniform clearance. It is shown that the circumferentially non-uniform clearance has less effect on the total pressure ratio and efficiency of compressor rotor, while it causes an obvious deterioration of the stall margin. Furthermore, the circumferentially non-uniform clearance causes the circumferential fluctuations of performance parameters, and the fluctuation amplitude has been affected by the eccentricity ratio and operating condition of rotor directly. In addition, the leakage flow originated from a single channel may pass through about three adjacent channels in rotor with uniform clearance, while it covers almost seven adjacent channels in the rotor with circumferentially non-uniform clearance. In consequence, it is precisely the difference of strength variation of leakage flow in tip region caused by the circumferential distributions of tip clearance that produces an alternated variation of low-velocity zone in rotor prototype and a concentrated distribution of low-velocity zone in the range of 270° to 360° of rotor with non-uniform clearance. Due to the serious blockage appearing in this range, the rotating stall of transonic rotor with circumferentially non-uniform clearance has occurred in advance, even with a maximum drop of 35.94% in stall margin.
Numerical Simulation Of A Transonic Centrifugal Compressor Blades Tip Clearance Flow Of Vehicle Turbocharger

Gongda Guo,Yangjun Zhang,Jianzhong Xu,Xinqian Zheng,Weilin Zhuge

DOI: https://doi.org/10.1115/GT2008-50957

2008-01-01

Abstract:Flow induced by blade tip clearance is important for centrifugal compressor, especially for the high charging ratio transonic centrifugal compressor of the vehicle. Based on three-dimensional CFD method, the evolution and mechanism of tip clearance flow for the high charging ratio transonic centrifugal compressor are investigated. It is verified that shock waves have important effect on blade tip clearance flow. The original position and strength of leakage vortices depend on the position and intensity of shock waves. The tip leakage vortex (TLV) evolution is influenced by the evolution of passage vortex (PV), corner vortex (CV) and separated vortex (SV). Shock wave, adverse pressure gradient and casing boundary layer accelerate the leakage vortices breakdown. Leakage vortex loss is the most important factor of impeller loss. The research on the blades tip leakage flow of transonic centrifugal compressor for vehicle lays a foundation for transonic centrifugal compressor flow control.
Role of Tip Leakage Flow in an Ultra-Highly Loaded Transonic Rotor Aerodynamics

Longxin Zhang,Songtao Wang,Site Hu

DOI: https://doi.org/10.1016/j.energy.2023.129596

IF: 9

2023-01-01

Energy

Abstract:Tip clearance size is a very critical design parameter for the modern transonic rotor. This investigation attempts to reveal the role of tip leakage flow in an ultra-highly loaded low reaction transonic rotor (loading coefficient equals to 0.782) aerodynamics. Flow fields in the rotor with varied tip clearance sizes, ranging from 0 to 3 times of the datum case, are discussed at length. Both performance variation and stall mechanisms involved are elaborated. As a result, the rotor performance presents a continuous decline with the increased tip clearance size as a result of the additional secondary flow loss induced by the tip leakage flow. While for stall margin, an optimal tip clearance size exists, and it happens to be the datum case. The tip leakage flow is found to have the ability to blow away the low-energy flow accumulated in the rotor tip suction side. Specially, the forward portion of tip leakage flow plays the dominate role in extending the rotor stall margin. However, as the tip clearance size exceeds the datum case, the shock-tip leakage vortex interaction causes the tip leakage vortex breakdown and the stall margin is hence narrowed.
Study on the Effect of Rotor Tip Fillet Edge in Axial Compressor

Song Mo-Ru,Wang Yue-Heng,Zhou Rui,Li Zixuan,Yang Bo

DOI: https://doi.org/10.1177/09576509221086462

2022-01-01

Abstract:The compressor flowfield is sensitive to the small geometry in the tip region. The blade tip edge, which was usually idealized as “sharp” edge in the numerical simulation, had been actually filleted during the process of machining, coating, and wearing. However, the fillet edge was completely neglected in the compressor performance estimation. Thus, in this paper, the effect of the fillet edge is evaluated by establishing several models with tip fillet edges as well as tip sharp edge in a transonic axial compressor. By the comparison of the flowfield between models with fillet edge and sharp edge, it was found that the tip fillet edge can eliminate the separation bubble at the pressure side of the tip clearance. Also, it can affect the tip clearance outflow by changing the reversed flow. As a result, the leakage flow is increased and the compressor performance is decreased in efficiency and pressure ratio. The local leakage mass flow rate along the camber line can be increased up to 40% when the fillet radius is as much as 20% of the tip clearance size. The flowfield in the downstream is also affected by the fillet edge. By the comparing among the models with different working conditions, it is found that the sensitivity of the performance to the fillet edge is different between design and off-design conditions. Furthermore, the effect of the tip fillet edge on the leakage flow is qualified and compared with the effect of the tip clearance.
Some Effects of Non-Axisymmetric Tip Clearance Layout on Axial Compressor Aerodynamics

Haohao Zhang,Haowan Zhuang,Jinfang Teng,Mingmin Zhu,Xiaoqing Qiang

DOI: https://doi.org/10.1177/09576509211047002

2022-01-01

Abstract:A steady and unsteady numerical research is carried out to explore some effects of a specific non-axisymmetric tip clearance layout on the overall performance and stability of an axial compressor stage. For a 4-stage low-speed research compressor (LSRC) in Shanghai Jiao Tong University (SJTU), one-eighth annulus of the inlet guide vane and the first stage rotor was modeled for this study. After the validation for the uniform tip clearance case, a specific non-axisymmetric tip clearance layout is chosen from several random cases generated by the Gaussian Probabilistic Density Function method. Unsteady time-averaged results at the near stall condition show that the chosen non-axisymmetric layout can improve the isentropic efficiency by 1.3% and extend the stall margin by 4%. Detailed analyses on flow fields are carried out to interpret the performance improvement. Due to the circumferential layout of clearance sizes, the inlet mass flow and incidence are redistributed in both the radial and circumferential directions. It leads to blade loading and tip leakage flow varying with the tip clearance size. The quantification of blockage manifests that the blockage arising from the tip leakage flow is significantly alleviated in the non-axisymmetric layout, which leads to improvements in overall performance and stall margin. Transient flow fields at the rotor tip are also analyzed at the near stall condition. For the non-axisymmetric layout, low-momentum regions originating from larger clearance sizes oscillate and develop downstream in one blade passage period.
Experimental and Numerical Investigations of Tip Injection on Tip Clearance Flow in an Axial Turbine Cascade

Maosheng Niu,Shusheng Zang

DOI: https://doi.org/10.1016/j.expthermflusci.2011.04.009

IF: 3.2

2011-01-01

Experimental Thermal and Fluid Science

Abstract:This investigation presents detailed experimental measurements of an active tip-clearance control method based on tip injection in a high-turning axial turbine cascade. Besides that, numerical investigations are also conducted to study phenomena which are not easily measured in the experiments. It aims to study the influence of tip injection on tip clearance flow, with emphasis on the effects of injection locations. Detailed flow field measurements were made downstream of the cascade using a three-hole probe. Static pressure distributions were also measured on the blade surface at 50% and 97.5% span, respectively. The results suggest that tip injection can weaken tip clearance flow, reducing the tip clearance mass flow and its associated losses. Meanwhile, the heat transfer condition on the blade tip surface can be also improved significantly. It also can be found that injection chordwise location plays an important role in the redistribution of secondary flow within the cascade passage. When the same number of injection holes and injection mass flow are applied, holes located in the aft part of blade can perform much better than that in the front part.
Influence of Tip Clearance Size on Flow Characteristics of a Vaneless Counter-Rotating Turbine

Qingjun Zhao,Jiafei Qiao,Huishe Wang,Xiaolu Zhao,Jianzhong Xu

DOI: https://doi.org/10.2514/6.2009-4836

2009-01-01

Abstract:In this paper, three-dimensional multiblade row Navier-Stokes simulations have been performed to investigate the effects of tip clearance size on the flow characteristics of a vaneless counter-rotating turbine. The tip clearance sizes studied in this paper are 0.0mm (without rotor tip clearance), 0.5mm (0.65% high-pressure turbine rotor height, 0.52% low-pressure turbine rotor height), 1.0mm, 1.5mm, 2.0mm, 2.5mm and 3.0mm, individually. The numerical results indicate that the air mass flow rate of the vaneless counter-rotating turbine and the ratio of specific work of the high-pressure turbine to that of the low-pressure turbine increase when the rotor tip clearance size is increased. While the isentropic efficiency, the expansion ratio and the power of the vaneless counter-rotating turbine decrease as the tip clearance size is increased. The results also show that the existence of the tip clearance trends to decrease the Mach number at the high-pressure turbine outlet, and increase the Mach number at the low-pressure rotor outlet, especially at near the blade tip region, the extents of the decrease and increase of the Mach number are more remarkable. When the tip clearance size is increased, the Mach number decreases at the outlet of the high-pressure turbine, while increases at the outlet of the low-pressure rotor. The numerical results also illustrate that the existence of the tip clearance trends to decrease the flow angle at the high-pressure turbine outlet, especially at near the blade tip region, the extent of the decrease of the flow angle is more prominent. And the flow angle decreases with the increase of the tip clearance size at the high-pressure turbine outlet. Compared with the results at the high-pressure turbine outlet, the effects of the tip clearance on the flow angle are more complicated at the low-pressure rotor outlet. Along the low-pressure rotor span, the outlet flow angle shows several different evolution laws with the increase of the tip clearance size.

A numerical study on the tip clearance in an axial transonic compressor rotor

Effects of tip clearance flow on aerodynamic performance of transonic axial compressor rotor

The Influence of Blade Root Fillet and Blade Tip Clearance on the Aerodynamic Performance of a Transonic Axial Compressor

Numerical investigation on the influence of nonuniform tip clearance on rotor tip-clearance flow field structure

Effect of Tip Clearance Size on the Performance of a Low-Reaction Transonic Axial Compressor Rotor

NUMERICAL SIMULATION STUDY ON THE EFFECT OF TIP CLEARANCE ON PERFORMANCE OF A TRANSONIC AXIAL FAN

Influence of Tip Clearance on Flow Characteristics of Axial Compressor

An Improved Model for Tip Clearance Loss in Transonic Axial Compressors

Numerical Study of the Flow in Axial Cascade with Tip Clearance

Numerical Simulation of tip clearance flow inside turbine rotors

Numerical Investigations on Aerodynamic Blockage Characteristics and Exit Blockage Prediction Model for Transonic Centrifugal Impellers

Tip Injection in Transonic Axial Compressor Rotor

Numerical Investigation of Tip Clearance Flow in a Variable Geometry Turbine with Non-Uniform Partial Clearance

Effect of Different Tip Clearance Treatments on Performance of an Axial-flow Compressor

Effects of Circumferentially Non-Uniform Clearance on the Spanwise Flow Characteristics in a Transonic Compressor Rotor

Numerical Simulation Of A Transonic Centrifugal Compressor Blades Tip Clearance Flow Of Vehicle Turbocharger

Role of Tip Leakage Flow in an Ultra-Highly Loaded Transonic Rotor Aerodynamics

Study on the Effect of Rotor Tip Fillet Edge in Axial Compressor

Some Effects of Non-Axisymmetric Tip Clearance Layout on Axial Compressor Aerodynamics

Experimental and Numerical Investigations of Tip Injection on Tip Clearance Flow in an Axial Turbine Cascade

Influence of Tip Clearance Size on Flow Characteristics of a Vaneless Counter-Rotating Turbine