Abstract:Abstract Flow separation is a major parameter affecting the compressor performance. It reduces the compressor efficiency, limits static pressure rise capability and contributes to instability in compressors. In applied research, there is a lack of understanding of the nature and mechanism of the three-dimensional (3-D) flow separation in the axial compressor especially on the juncture of the endwall and blade corner region. In the present study, the 3-D flow field in an axial compressor cascade has been studied experimentally as well as numerically. For the experimental study part, a linear compressor cascade has been installed in an open loop wind tunnel. The experimental data was acquired for a Reynolds number Rec = 2.98 × 105 based on the blade chord and the inlet flow conditions. The total pressure loss progress through the blade passage has been measured by using calibrated five and seven-hole pressure probes connected to ATX sensor module data acquisition system. The static pressure distribution on the endwall has been measured employing static pressure taps connected to digital micromanometers. To investigate the loss mechanism through the cascade, the total pressure loss coefficient has been calculated from the measured data. The computational fluid dynamics (CFD) study of the flow field was performed to gain a better understanding of the flow features. Two turbulence models, Spalart-Allmaras (S-A) and shear stress transport SST (k-ω) were used. From both parts of study, the flow field development and total pressure loss progress through the cascade have been investigated and compared. Moreover, the received data demonstrated a good agreement between the experimental and computational results. The predicted flow streamlines by numerical calculations showed regions characterized by flow separation and recirculation zones that could be used to enhance the understanding of the loss mechanism in compressor cascades. All measurements taken by 5-hole and 7-hole pressure probes have been analyzed and compared. It was found that their readings were almost the same and there are no excellences for using 7-hole probe. Furthermore S-A turbulence model calculations showed more consistencies with experimental results than SST (k-ω) model.

Oil Flow Visualization and Numerical Calculation on End-Wall of Aspirated Compressor Cascade

An Experimental Study of Turbine Vane Film Cooling Using Endoscope-Based PSP Technique in a Single-Passage Wind Tunnel

Numerical Study On End-Wall Flow In Highly Loaded Supercritical Compressor Cascades

Effects of endwall boundary layer suction position on the flow field and load in a high-turning compressor cascade

Numerical Simulation of Effect of Blade End Slot on Performance of Compressor Cascade

Influence of Moving End-Wall on Tip Clearance Flow in an Axial-Flow Compressor Cascade

Flow quality improvement of the wind tunnel testing for a highly-loaded compressor cascade at high incidence

Study about flow field control of vane of HP centrifugal compressor by boundary layer suction

Study on Flow Structure of a Highly-Loaded Compressor Cascade Designed with Active and Passive Flow Control Methods

INVESTIGATION OF SEPARATION AND FLOW FILED STRUCTURE IN HIGH-LOADING COMPRESSOR CASCADES

Experimental and numerical investigation for flow in bowed compressor cascade with large turning angles

Effect of Boundary Layer Suction on Aerodynamic Performance of High-Turning Compressor Cascade

Experimental Analysis of Performance and Tip Dynamic Pressure in a Compressor Cascade with High-Speed Moving Endwall

Experimental and Numerical Investigations of Pressure Loss and 3-D Flow Separations in a Linear Compressor Cascade

Non-Axisymmetric Endwall Contouring in a Linear Compressor Cascade

Blade Aerodynamic Force and Tip Region Vortex Spatial-temporal Evolution Study of a Compressor Cascade

Numerical Simulation for Applying Boundary Layer Suction on End-wall to Improve the Aerodynamic Performance of Cascade

Effect of Blade Sweeping-Curving on the Endwall Flow Field of Compressor Cascade

A COMBINED APPLICATION OF NEGATIVE BOWED BLADE AND ENDWALL UNSTEADY PULSED HOLED SUCTION IN A HIGHLY LOADED COMPRESSOR CASCADE

Impact of End-wall Boundary Layer Suction on the Separation Structure in a Diffuser Cascade

Analysis of Leakage Flow and Loss in a Linear Compressor Cascade with Moving Endwall